Results
This document defines the test procedures and performance limits of steady state and transient voltage characteristics for 12 V, 24 V, or 48 V electrical power generating systems used in commercial ground vehicles.
This specification covers a low-alloy steel in the form of bars, forgings, mechanical tubing, and forging or tubing stock.
This supplement forms a part of SAE Aerospace Specification AS85421. It shall be used to identify fitting standards citing this procurement specification.
This specification establishes the requirements for various types of identification sleeving that will shrink to a predetermined size upon the application of heat after it has been marked. Continuous operating temperature ratings range from -55° to 175°C (-67° to 347°F). (See 6.1).
The accompanying mounting and gear locations are applicable for all general installations of power take-off on the transmission gear box of motor trucks and tractors where the size of the transmission permits. The heavy-duty type opening can be adapted to the regular-duty type by the use of an adapter with 6.35 mm (0.25 in) flange thickness with appropriate bolt pattern and thread engagement. (See Figures 1 and 2.)
This specification covers an aluminum alloy in the form of plate.
CLARA identifies four functions: Data Space Generator, Truth Data Generator, Coefficient Generator, and Reconstructor. Together these four functions standardize the solution to the LAR problem. This ICD defines the logical interfaces of the four functions.
Shortly after World War II, as aircraft became more sophisticated and power-assist, flight-control functions became a requirement, hydraulic system operating pressures rose from the 1000 psi level to the 3000 psi level found on most aircraft today. Since then, 4000 psi systems have been developed for the U.S. Air Force XB-70 and B-1 bombers and a number of European aircraft including the tornado multirole combat aircraft and the Concorde supersonic transport. The V-22 Osprey incorporates a 5000 psi hydraulic system. The power levels of military aircraft hydraulic systems have continued to rise. This is primarily due to higher aerodynamic loading, combined with the increased hydraulic functions and operations of each new aircraft. At the same time, aircraft structures and wings have been getting smaller and thinner as mission requirements expand. Thus, internal physical space available for plumbing and components continues to decrease.
This specification covers a premium aircraft-quality, high-alloy steel gas-atomized and HIP-consolidated in the form of bars, wire, forgings, and forging stock.
This Aerospace Recommended Practice (ARP) outlines the causes and impacts of moisture and/or condensation in avionics equipment and provides recommendations for corrective and preventative action.
This specification covers an adhesive compounded from modified epoxy resins in ready-to-use film, supplied in rolls or sheets, either supported by mat or by woven monofilaments or unsupported.
This specification covers an aircraft-quality, low-alloy steel in the form of bars, forgings, and forging stock.
This specification covers an aluminum alloy in the form of castings.
This standard applies to pressure reducers for gaseous breathing oxygen systems and for all performance profiles without regard to particular inlet or outlet pressures. Attention is given, however, to construction requirements for reducers with maximum supply pressures to 2250 psig (155 bar) and reduced pressures of 50 to 150 psig (3.4 to 10.5 bar).
This specification covers a carbon steel in the form of sheet and strip.
This SAE Recommended Practice describes the test procedures for conducting quasi-static modular body strength tests for ambulance applications. Its purpose is to establish recommended test practices which standardize the procedure for Type I and Type III bodies, provide ambulance builders and end-users with testing procedures and, where appropriate, provide acceptance criteria that, to a great extent, ensures the ambulance structure meets the same performance criteria across the industry. Descriptions of the test set-up, test instrumentation, photographic/video coverage, and the test fixtures are included.
Wire and cable products progress through a series of handling or operational steps from the time they leave the manufacturer, and until a finished harness or assembly is ready for installation on a vehicle. Throughout these many steps, environmental or processing conditions may be present which can generate damage detrimental to the wire or cable and/or its intended application.
This SAE Aerospace Recommended Practice (ARP)4294 is directed at life cycle cost (LCC) analysis of aerospace propulsion systems and supplements AIR1939. Specific topics addressed by ARP4294 are listed below: a Propulsion system LCC element structure. b Information exchange and relationships with: (1) Aircraft manufacturer (2) Equipment suppliers (3) Customer c The relationship of the LCC element structure to work breakdown structures. d The relationship between LCC analysis and other related disciplines (e.g., technical (performance analysis, weight control, component lives), reliability, availability and maintainability (RAM), integrated logistic support (ILS), production and finance). e Classification of the accuracy and applicability of LCC assessments.
This AS covers Vertical Velocity Instruments which display the rate of change of pressure altitude of an aircraft, as follows: Type A - Direct reading, self-contained, pressure actuated Type B - Electrically or electronically operated, self-contained, pressure actuated Type C - Electrically or electronically operated, input from a remote pressure sensor
This document provides a recommended electrical performance testing guideline for LIBM, which makes up an xEV (Battery Electric Vehicles and Hybrid Electric Vehicles) battery pack system. This testing guideline may also be used for other applications, such as stationary, vessel, and aircraft. However, using the guideline for other applications should be determined by the users of this document. Users of this document may also be interested in conducting tests on battery cells and/or battery packs. To avoid conducting potentially redundant tests between cells, modules, and packs, this document does not specify which tests need to be conducted. Determination of which tests need to be conducted is at the user’s discretion and should be based on individual module applications. Rather than specifying which tests need to be conducted, this document describes how each test is to be conducted. This document provides a matrix of tests that can be selectively picked for the application
Items per page:
50
1 – 50 of 221567