Results
This SAE Standard provides test procedures for air and air-over-hydraulic disc or drum brakes used for on-highway commercial vehicles over 4536 kg (10000 pounds) GVWR. This recommended practice includes the pass/fail criteria of Federal Motor Vehicle Safety Standard No. TP-121D-01.
SCOPE IS UNAVAILABLE.
SCOPE IS UNAVAILABLE.
This specification covers a coating consisting of tungsten disulfide without binders and does not require a curing process.
This specification covers a magnesium alloy in the form of extruded bars, rods, wire, tubing, and profiles.
This specification covers an aluminum alloy in the form of hand forgings up to 8 inches (203 mm), inclusive, in nominal thickness and a cross-sectional area not over 256 square inches (1652 cm2) and rolled rings up to 3.5 inches (89 mm), inclusive, in nominal thickness and with an OD to wall thickness ratio of 10:1 or greater (see 8.6).
This specification covers a titanium alloy in the form of bars up through 3.000 inches (76.20 mm), inclusive, in diameter or least distance between parallel sides with a maximum cross-sectional area of 10 square inches (64.5 cm2) and forging stock of any size (see 8.7).
This specification covers a magnesium alloy in the form of plate 0.250 to 2.000 inches (6.35 to 50.80 mm), inclusive, in nominal thickness (see 8.5).
This SAE Aerospace Standard (AS) covers miniature, composite, high density, threaded coupling, self-locking, circular, environment-resistant, electrical connectors utilizing removable crimp contacts, and associated hardware, which are capable of continuous operation within a temperature range of -65 to +175 °C (-85 to 347 °F). These connectors are supplied under an AS9100 reliability assurance program. See 6.1 for intended use and applications.
This specification covers an aluminum alloy in the form of rolled or forged rings up to 6 inches (152 mm), inclusive, in nominal thickness at the time of heat treatment and having an OD to wall thickness ratio of 10 or greater (see 8.6).
This SAE Aerospace Recommended Practice (ARP) defines lightning strike zones and provides guidelines for locating them on particular aircraft, together with examples. The zone definitions and location guidelines described herein are applicable to Parts 23, 25, 27, and 29 aircraft. The zone location guidelines and examples are representative of in-flight lightning exposures.
This specification covers a magnesium alloy in the form of sand castings.
This specification covers an aluminum alloy in the form of wire, sheet, foil, pig, grains, shot, and chips.
This specification covers a carbon steel in the form of sheet and strip.
Compositions apply to the finished bearing or bearing lining, not necessarily to the alloy at an intermediate processing stage. All values not given as ranges are maxima. (See Tables 1 through 5.)
This specification covers one weight and type of weave of aramid cloth.
This specification covers the requirements for electrodeposited tin-lead plating intended for use as a coating for corrosion protection and as a base for soldering.
This specification covers cotton-fabric-reinforced chloroprene (CR) rubber in the form of sheet.
This specification covers a silver brazing flux in the form of paste.
This specification covers a premium aircraft-quality, high-alloy steel gas-atomized and HIP-consolidated in the form of bars, wire, forgings, and forging stock.
This specification covers an aircraft-quality, low-alloy steel in the form of seamless tubing.
This specification covers an adhesive compounded from modified epoxy resins in ready-to-use film supplied in rolls or sheets, either supported by mat or by woven monofilaments or unsupported.
This specification covers a corrosion and heat-resistant cobalt alloy in the form of welding wire.
This specification covers cored and uncored open cell latex foam rubber sheets, molded and hand- built shapes having good shock-absorbing, vibration-damping, and comfort cushioning characteristics (see 6.1).
This specification covers a nitrile (NBR) rubber in the form of sheet, strip, tubing, extrusions, and molded shapes.
This specification covers one type of organic fiber in the form of yarn. The product shall be formed as a multiplicity of filaments drawn together and gathered into an approximately parallel arrangement.
This specification covers the requirements for identification of finished parts.
This specification covers the specific requirements for seamless tube drawn from aluminum alloy 6061.
This specification covers an aluminum alloy in the form of extruded bars, rods, wire, profiles, and tubing.
This specification covers one type of epoxy-resin-impregnated organic fibers in the form of woven cloth.
This specification and its supplementary detail specifications covers organic fibers in the form of continuous, multifilament yarn and roving.
This specification covers a room-temperature-vulcanizing, elastomeric silicone compound.
This specification covers a corrosion and heat resistant vacuum melted nickel alloy in the form of investment castings.
This specification covers one type of organic fiber in the form of yarn. The product shall be formed as a multiplicity of filaments drawn together and gathered into an approximately parallel arrangement.
This specification covers established inch/pound manufacturing tolerances applicable to low-alloy steel sheet, strip, and plate ordered to inch/pound dimensions. These tolerances apply to all conditions unless otherwise noted. The term “excl” is used to apply only to the higher figure of the specified range.
This specification covers alumina-silica, glass, and other ceramic fiber thermal insulation in the form of felt and fabric flat sheets, rolls, or molded non-pliable blocks. Nominal thickness is 0.1 to 2.0 inches (3 to 51 mm) and nominal density is 2 to 24 pounds mass per cubic foot (32 to 384 kg/m3).
This specification covers a nitrile (NBR) rubber in the form of sheet, strip, tubing, extrusions, and molded shapes.
This specification covers an aluminum alloy in the form of sheet clad on both sides with a different aluminum alloy.
This specification covers epoxy-resin-impregnated glass laminates in the form of sheets clad on one or both sides with electrolytic copper foil.
This specification covers dense, ultra-high alumina in the form of moldings and extrusions.
This specification covers a beryllium aluminum alloy in the form of investment castings.
This specification covers a premium aircraft-quality, high-alloy steel gas-atomized and HIP-consolidated in the form of bars, wire, forgings, and forging stock.
Items per page:
50
1 – 50 of 215736