Results
This specification covers a blend of chromium carbide and a nickel-chromium alloy in the form of powder.
This SAE Information Report SAE J2836/6 establishes use cases for communication between plug-in electric vehicles and the EVSE for wireless energy transfer as specified in SAE J2954. It addresses the requirements for communications between the on-board charging system and the wireless EV supply equipment (WEVSE) in support of detection of the WEVSE, the charging process, and monitoring of the charging process. Since the communication to the charging infrastructure and the power grid for smart charging will also be communicated by the WEVSE to the EV over the wireless interface, these requirements are also covered. However, the processes and procedures are expected to be identical to those specified for V2G communications specified in SAE J2836/1. Where relevant, the specification notes interactions that may be required between the vehicle and vehicle operator, but does not formally specify them. Similarly, communications between the on-board charging sub-system and the on-board vehicle
This document provides recommendations involving BEV battery data retention and battery design that enhance the potential for BEV battery reuse and serviceability and that can improve recyclability. These recommendations have been developed by a group of professionals skilled in the secondary-use of batteries and in the research, development, and manufacture of BEV batteries and battery systems.
The automotive air-conditioning service ports task force conducted a field survey with MACS (Mobile Air Climate Systems Association) in June 2021. The scope of this survey was to determine the types of failures reported primarily at member service shops related to automotive air-conditioning service ports.
This Information Report relates to a special class of automotive adaptive equipment which consists of modifications to the power brake booster systems provided as original equipment of motor vehicles. These modifications are generically called "Reduced Effort Power Brakes" (REPB) The purpose of the modification is to lower the amount of driver effort required to apply the brakes. Retention of reliability, ease of use and maintainability for disabled drivers, passengers, and the general public is of primary concern. Reduced Effort Power Brake modifications should be qualified by the tests referenced in the Recommended Test Procedure. The tests set forth in that procedure should be applied, and failure of a Reduced Effort Power Brake modification to meet those tests should disqualify the modification from the claim of meeting the specifications of this Information Report. Because this is an Information Report, the numerical values for performance measurements presented in this report and
This SAE Recommended Practice is intended to provide basic information on properties and characteristics of high-strength carbon and alloy steels which have been subjected to special die drawing. This includes both cold drawing with heavier-than-normal drafts and die drawing at elevated temperatures.
This SAE Aerospace Standard (AS) contains a sample test plan for AS15531 or MIL-STD-1553B Remote Terminals (RT) that may serve several different purposes. This document is intended to be contractually binding when specifically called out in a specification, Statement of Work (SOW), or when required by a Data Item Description (DID). Any and all contractor changes, alterations, or testing deviations to this section shall be separately listed for easy review.
This specification establishes the common requirements for variable delivery electric motor driven, hydraulic pump units, suitable for use in aircraft hydraulic systems.
The purpose of this SAE Information Report is to provide general information relative to the nature and use of eddy current techniques for nondestructive testing. The document is not intended to provide detailed technical information but to serve as an introduction to the principles and capabilities of eddy current testing, and as a guide to more extensive references listed in Section 2.
The scope of this SAE Information Report is to provide general information relative to the nature and use of magnetic particles for nondestructive testing. The document is not intended to provide detailed technical information, but will serve as an introduction to the theory and capabilities of magnetic particle testing, and as a guide to more extensive references.
The scope of this SAE Information report is to provide basic information on ultrasonics, as applied in the field of nondestructive inspection. References to detailed information are listed in Section 2.
This specification covers a premium aircraft-quality maraging steel in the form of bars and forgings, 0.50 to 8.00 inches (12.7 to 203.2 mm) in nominal diameter or least distance between parallel sides, and forging stock of any size.
This report approaches the material selection process from the designer's viewpoint. Information is presented in a format designed to guide the user through a series of decision-making steps. "Applications criteria" along with engineering and manufacturing data are emphasized to enable the merits of aluminum for specific applications to be evaluated and the appropriate alloys and tempers to be chosen.
This test plan is broken into three major sections for the testing of bus controllers Electrical, Protocol and Noise tests.
This test plan defines the requirements of data bus components which comply with the requirements of MIL-STD-1553B, Digital Time Division Command/Response Multiplex Data Bus.
An enormous economic loss, as well as a waste of natural resources, is incurred world-wide as a result of wear of components and tools. Any effort expended in an attempt to reduce this loss is indeed worthwhile. The purpose of this SAE Information Report is to present the current state of knowledge of abrasive wear. This report, therefore, covers wear, or the undesired removal of metal by mechanical action, caused by abrasive particles in contact with the surface. It does not concern metal-to-metal wear or wear in the presence of an abrasive free lubricant. Abrasive wear occurs when hard particles, such as rocks, sand, or fragments of certain hard metals, slide or roll under pressure across a surface. This action tends to cut grooves across the metal surface, much like a cutting tool. Abrasive wear is of considerable importance in any part moving in relation to an abrasive. Tools in contact with the ground, such as plows, cultivators, scraper and bulldozer blades, are intended to
Items per page:
50
1 – 50 of 219706