Results
This AIR provides information about the specific requirements for missile hydraulic pumps and their associated power sources.
This document describes the major design drivers and considerations when designing a fuel system for a large commercial aircraft. While not intended as a design manual for individual system components, it does refer out to other SAE specifications where more detail on specific components and subsystems is given. It does include examples of a number of calculations associated with sizing of fuel systems, based on those given in NAVAIR 06-5-504, as well as an appendix summarizing basic fluid mechanical equations that are key for fuel system design. It is acknowledged that most of these calculations would today be performed by modeling tools rather than by hand, but it is considered important for the designer to understand the principles. Some details specific to military aircraft are included, but it is intended that later issues of this document will include appendices that give specific considerations for military aircraft, smaller commercial aircraft, and rotorcraft. Features unique
This SAE Aerospace Recommended Practice (ARP) is intended to be used for laser systems mounted on aircraft and propagated into navigable airspace. This does not include lasers onboard aircraft where the beam is contained within an enclosure so that the beam cannot enter into airspace, nor does it include lasers from satellites and spacecraft in outer space. It may be used in conjunction with AS4970, ARP5535, ARP5572, ARP5293, and the ANSI Z136 laser safety standards.
This document and the EUROCAE equivalent, ED-107, provides detailed information, guidance, and methods in support of the Federal Aviation Administration (FAA) Advisory Circular (AC) 20-158 and to the European Union Aviation Safety Agency (EASA) AMC 20-158. AC 20-158 provides a means, but not the only means, for demonstrating compliance with Title 14 of the Code of Federal Regulations (14 CFR) 23.1308 (Amendment 57 and lower), 23.2520 (Amendment 64 and higher), 25.1317, 27.1317, 29.1317, and applicable FAA HIRF special conditions addressing HIRF Protection. AMC 20-158 is applicable to Certification Specifications CS 23.1308 (Amendment 4 and lower), 23.2520 (Amendment 5 and higher), 25.1317, 27.1317, and 29.1317. It should be noted that this document is neither mandatory nor regulatory in nature and does not constitute a regulation or legal interpretation of the regulation. Therefore, an applicant may elect to establish an alternative method of compliance that is acceptable to the
SCOPE IS UNAVAILABLE.
This specification covers the requirements for electrodeposited gold plate.
This specification covers a corrosion- and heat-resistant nickel alloy in the form of sheet, strip, and foil 0.100 inch (2.54 mm) and under in nominal thickness.
This specification establishes the engineering requirements for the uphill quenching process of aluminum alloy product. Uphill quenching immerses product in liquid nitrogen followed by exposure to a high-pressure/high-velocity steam blast or boiling water.
This specification covers a copper alloy in the form of strip (see 8.6).
This specification covers a corrosion-resistant steel in the form of sand or centrifugal castings.
This specification covers a corrosion-resistant steel in the form of investment castings.
This specification covers a low-alloy steel in the form of investment castings.
This specification covers a corrosion-resistant nickel-copper alloy in the form of bars up to 3.00 inches (76.2 mm), inclusive, in thickness and forgings and forging stock of any size.
This specification covers a corrosion- and heat-resistant steel in the form of sheet, strip, and plate over 0.002 inch (0.051 mm) in thickness.
This SAE Aerospace Recommended Practice (ARP) is intended to cover all external lights on the tanker and fixed wing receiver airplanes used to accomplish aerial refueling. This ARP describes lights used for two basic types of aerial refueling: the probe and drogue, and the boom/receptacle method.
This appendix covers requirements for system and end item documentation and procedures used for the standard galley system.
This specification covers a corrosion- and moderate heat-resistant steel in the form of sheet, strip, and plate.
This specification covers a corrosion and moderate heat-resistant steel in the form of investment castings.
This specification covers a corrosion and moderate heat resistant steel in the form of investment castings.
The scope of this ARP is to provide general requirements for application of electroluminescence to Aerospace Vehicle Crew Station Area instruments and control panels. The design brightness and color recommendations stated in this ARP are intended to apply where a crew station has multiple usage of electroluminescence in both instruments and control panels and when different manufacturers may be involved. These recommendations may also be helpful for the design of individually used displays incorporating electroluminescence, however, this light source has extensive design versatility through variance of manufacturing and operating parameters and the numerous acceptable design recommendations will not be stated herein. Electroluminescence will herein be referred to as EL.
This ARP describes a gravimetric method for the determination of particulate contaminant in hydraulic fluids by the control filter technique. NOTE: With this method, detectable contamination levels down to 0.2 mg (7.0 × 10-6 ounces) per sample can be obtained with a standard deviation of ±0.1 mg (±3.5 × 10-6 ounces).
This SAE Aerospace Recommended Practice (ARP) covers the general requirements and test procedures recommended for use with white incandescent integrally lighted instruments. Its use should provide uniformity of illumination from instrument to instrument and legibility under daylight operation. An appendix is provided to familiarize the designer with some of the techniques used to obtain uniformity of color and illumination in various types of instruments.
This SAE Aerospace Standard (AS) establishes the requirements for straight threaded boss or flanged fluid connection fittings (see Section 6) for use in all types of fluid systems.
This SAE Standard defines the test conditions, procedures, and performance specifications for 6 V and 12 V stop lamp switches intended for use on motorcycles.
This SAE Aerospace Recommended Practice (ARP) defines the performance criteria and validation for tire circumferential movement on the rim, in the laboratory, by a static test, as well as a performance assessment in service. This document is applicable to braked wheel positions using both bias ply and radial aircraft tires.
This SAE Aerospace Recommended Practice (ARP) provides a guide for preparation of requirements for general design, performance, and testing of mechanical geared rotary actuators intended to be used for applications requiring motion control in response to manual or automatic power control system inputs.
This document summarizes the need for power take-off pads on gas turbine engines intended for helicopter power plant installations.
The purpose of this SAE Aerospace Recommended Practice (ARP) is to provide recommendations for marking wire and cable insulations to meet legibility requirements. This information is generic and applies to any type of wire marking system, such as an ultraviolet (UV) laser marking system or an inkjet or other ink based wire marking system. This ARP is limited to the legibility of human-readable characters and does not address bar code or other machine-readable symbols. In this ARP, the term wire refers to jacketed cables and fiber optic cables in addition to individual wires. This ARP defines the factors that affect the legibility of markings on wiring. Two generic types of variables affect legibility: stimulus variables and environmental variables. Stimulus variables are those factors involving the mark itself. This ARP establishes a set of guidelines for key stimulus variables that contribute to legibility and which should be taken into consideration in the course of specifying and
This document is intended to explain, in detail, the rationale behind the features and functions of the AS4074, Linear, Token-passing, Bus (LTPB). The discussions also address the considerations which a system designer should take into account when designing a system using this bus. Other information can be found in these related documents: AIR4271 - Handbook of System Data Communication AS4290 - Validation Test Plan for AS4074
This SAE Aerospace Information Report (AIR) supplies information on the flight control systems incorporated on various current and historic fixed wing, rotary wing, and tilt rotor aircraft. A brief description of the aircraft is followed by a description of the flight control system, some specific components, drawings of the internal arrangement, block diagrams, and schematics. System operation redundancy management is also presented.
Items per page:
50
1 – 50 of 219583