Results
This AIR provides information about the specific requirements for missile hydraulic pumps and their associated power sources.
The purpose of this SAE Recommended Practice is to establish a uniform laboratory procedure for securing and reporting the friction and wear characteristics of brake linings. The performance data obtained can be used for in-plant quality control by brake lining manufacturers and for the quality assessment of incoming shipments by the purchasers of brake linings.
This SAE Recommended Practice establishes the test procedure, environment, and instrumentation to be used for measuring the exterior exhaust sound level for passenger cars, multipurpose vehicles, and light trucks under stationary conditions providing a continuous measure of exhaust system or simulated exhaust sound level over a range of engine speeds or simulated engine speeds. This document applies only to road vehicles equipped with an internal combustion engine or with an external sound system. The method is designed to meet the requirements of simplicity as far as they are consistent with reproducibility of results under the operating conditions of the vehicle. It is within the scope of this document to measure the stationary A-weighted sound pressure level during: Measurements at the manufacturing stage Measurements at official testing stations Measurements at roadside testing It does neither specify a method to check the exhaust sound pressure level when the engine is operated at
This document describes the 2-D computer-aided design (CAD) template for the HPM-1 H-point machine or HPD available from SAE. The elements of the HPD include the curve shapes, datum points and lines, and calibration references. The intended purpose for this information is to provide a master CAD reference for design and benchmarking. The content and format of the data files that are available are also described.
Most signal and marking lighting devices have light sources (bulbs), which can be based on either filament or LED technology. To assure field replacement, it is important that light source types employed be readily available in normal service channels. This document defines the physical, electrical, and photometric characteristics necessary to achieve a proper replacement for popular types of signal and marking light sources. Some of the design characteristics in this document are listed solely for the sake of standardization and are not intended to describe the performance of lighting devices (lamp assemblies) on the vehicle. Halogen filament light sources suitable for signal and marking lighting are specified in SAE J2560.
This SAE Recommended Practice provides test procedures, performance requirements, and guidelines for cleaners intended for use on motor vehicles.
This specification covers a polyalphaolefin/ester-blend fluid.
This specification covers one type of paper in the form of perforated tape of the width specified herein.
This specification covers a polytetrafluoroethylene (PTFE) resin filled with 40% bronze powder in the form of extruded or molded rods or tubes which are sintered after molding or, in the case of extrusions, sintered during the extrusion process.
This specification covers one type of nylon in the form of webbing.
This specification covers one width and strength of nylon tape.
This specification covers steel in the form of laminated sheet.
This specification covers one weight and strength of para-aramid thread.
This specification covers one width and strength of nylon tape.
This specification covers an unfilled grade of virgin polytetrafluoroethylene (PTFE) resin in the form of extruded or molded rods or tubes which are sintered after molding or, in the case of extrusions, sintered during the extrusion process.
In 1941, the SAE Iron and Steel Division in collaboration with the American Iron and Steel Institute (AISI) made a major change in the method of expressing composition ranges for the SAE steels. The plan, as now applied, is based in general on narrower ladle analysis ranges plus certain product (check) analysis allowances on individual samples, in place of the fixed ranges and limits without tolerances formerly provided for carbon and other elements in SAE steels (reference SAE J408). ISTC Division 1 has developed a procedure which allows for the maintenance of the grade list in this SAE Standard. This will involve conducting an industry-wide survey to solicit input. This survey will be conducted at a frequency deemed necessary by the technical committee. Criteria have been established for the addition to or deletion of grades from the grade table. A new grade will be considered if it meets standard SAE grade ranges, has a minimum usage or production of 225 tonnes/year (250 tons/year
This specification covers a silicone rubber sponge in the form of sheet, strip, extrusions, and molded shapes.
This specification covers one type of epoxy-resin-impregnated carbon fibers in the form of tape and sheet.
This specification covers one type of epoxy-resin-impregnated carbon fibers in the form of tape and sheet.
This specification covers one type of epoxy-resin-impregnated, non-woven, glass fiber in the form of tape for hand or machine layup and of flat sheet.
This specification covers one type of copper-beryllium alloy in the form of wire.
This specification covers the specific requirements for aluminum alloy 5083 bar, rod, shapes, tube, and wire produced by extrusion.
This specification covers the engineering requirements and process for brush plating of silver by electrodeposition. It shall be used, in conjunction with AMS2451, for silver deposits.
This specification covers one type of organic (para-aramid) fiber in the form of roving. The product shall be formed as a number of ends, tows, or strands collected into a parallel bundle with little or no twist.
This specification covers a copper-zinc alloy (brass) in the form of laminated sheet with nominal thickness 0.006 to 0.125 inch (0.15 to 3.18 mm) (see 8.5).
This specification covers procedures for identifying bars, wire, mechanical tubing, and extrusions of carbon and alloy steels and corrosion and heat-resistant steels and alloys.
This specification covers one weight and one weave of novoloid/aramid cloth.
This specification covers one type of organic (para-aramid) fiber in the form of roving. The product shall be formed as a number of ends, tows, or strands collected into a parallel bundle with little or no twist.
This SAE Standard provides general design performance requirements and related test procedures for composite lighting unit assemblies, other than signaling and marking devices, used on earthmoving and road building and maintenance off-road work machines as defined in SAE J1116.
This specification covers a premium aircraft-quality, corrosion-resistant steel in the form of sheet, strip, and plate.
SCOPE IS UNAVAILABLE.
The purpose of this Standard is to provide installation dimensions for shaft nuts and their companion keywasher. The Standard type typically shown on MS9951 and MS9952, but is also suitable for parts which are dimensionally equivalent.
Items per page:
50
1 – 50 of 216049