Results
This SAE Information Report SAE J2836/6 establishes use cases for communication between plug-in electric vehicles and the EVSE for wireless energy transfer as specified in SAE J2954. It addresses the requirements for communications between the on-board charging system and the wireless EV supply equipment (WEVSE) in support of detection of the WEVSE, the charging process, and monitoring of the charging process. Since the communication to the charging infrastructure and the power grid for smart charging will also be communicated by the WEVSE to the EV over the wireless interface, these requirements are also covered. However, the processes and procedures are expected to be identical to those specified for V2G communications specified in SAE J2836/1. Where relevant, the specification notes interactions that may be required between the vehicle and vehicle operator, but does not formally specify them. Similarly, communications between the on-board charging sub-system and the on-board vehicle
This specification covers a blend of chromium carbide and a nickel-chromium alloy in the form of powder.
This document provides recommendations involving BEV battery data retention and battery design that enhance the potential for BEV battery reuse and serviceability and that can improve recyclability. These recommendations have been developed by a group of professionals skilled in the secondary-use of batteries and in the research, development, and manufacture of BEV batteries and battery systems.
The automotive air-conditioning service ports task force conducted a field survey with MACS (Mobile Air Climate Systems Association) in June 2021. The scope of this survey was to determine the types of failures reported primarily at member service shops related to automotive air-conditioning service ports.
This Information Report relates to a special class of automotive adaptive equipment which consists of modifications to the power brake booster systems provided as original equipment of motor vehicles. These modifications are generically called "Reduced Effort Power Brakes" (REPB) The purpose of the modification is to lower the amount of driver effort required to apply the brakes. Retention of reliability, ease of use and maintainability for disabled drivers, passengers, and the general public is of primary concern. Reduced Effort Power Brake modifications should be qualified by the tests referenced in the Recommended Test Procedure. The tests set forth in that procedure should be applied, and failure of a Reduced Effort Power Brake modification to meet those tests should disqualify the modification from the claim of meeting the specifications of this Information Report. Because this is an Information Report, the numerical values for performance measurements presented in this report and
This SAE Recommended Practice is intended to provide basic information on properties and characteristics of high-strength carbon and alloy steels which have been subjected to special die drawing. This includes both cold drawing with heavier-than-normal drafts and die drawing at elevated temperatures.
This document sets forth design and operational recommendations concerning the human factors issues and criteria for airborne terrain separation assurance systems. The visual and aural characteristics are covered for both the alerting components and terrain depiction/situation components. The display system may contain any one or a combination of these components. Although the system functionality assumed for this document exemplifies commercial aircraft implementation, the recommendations do not exclude other fixed wing aircraft types. Because of their unique operations with respect to terrain, rotorcraft will be addressed in a separate document. The assumptions about the system that guided and bounded the recommendations included: the system will have a human centered design based on the "lessons learned" from past systems; the system is not intended to replace the Ground Proximity Warning System (GPWS) function; the system is an on-board system that is not dependent on ground
All safety glazing materials used in motor vehicles and motor vehicle equipment operating on land highways should comply with the requirements of the American National Standard, ANSI/SAE Z-26.1. The American National Standard for Safety Glazing Materials for Glazing Motor Vehicles and Motor Vehicle Equipment Operating on Land Highways—Safety Standard, ANSI/SAE Z-26.1-1996 is the latest complete updated version and is referred to hereafter as “the safety standard.” This SAE Recommended Practice is not intended to preclude references to any governmental law, ordinance, or regulation which might apply to the glazing of motor vehicles and motor vehicle equipment operating on land highways.
This SAE Standard covers fittings intended for connecting service hoses, per SAE J2196, from Mobile Air-Conditioning Systems to service equipment such as manifold gauges, vacuum pumps and air conditioning charging, recovery and recycling equipment. (Figure 1)
The scope of this SAE Information Report is to provide general information relative to the nature and use of infrared techniques for nondestructive testing. The document is not intended to provide detailed technical information, but will serve as an introduction to the theory and capabilities of infrared testing and as a guide to more extensive references.
(These definitions were prepared by the Joint Committee on Definitions of Terms Relating to Heat Treatment appointed by the American Society for Testing and Materials, The American Society for Metals, the American Foundrymen's Association, and the SAE.) This SAE revision emphasizes the terms used in heat treating ferrous alloys, but also includes for reference some non-ferrous definitions at the end of the document. This glossary is not intended to be a specification, and it should not be interpreted as such. Since this is intended to be strictly a set of definitions, temperatures have been omitted purposely.
The design and location of rear-viewing mirrors or systems, and the presentation of the rear view to the driver can best be achieved if the designer and the engineer have adequate references available on the physiological functions of head and eye movements and on the perceptual capabilities of the human visual system. The following information and charts are provided for this purpose. For more complete information of the relationship of vision to forward vision, see SAE SP-279.
This SAE Recommended Practice establishes the instrumentation and procedure to be used in measuring the maximum exterior sound level for engine powered equipment under 14.7 kW (20 bhp). It is intended to include equipment such as lawn mowers, snow blowers, tillers, etc. It is not intended to include equipment designed primarily for operation on highways or within factories and buildings, or vehicles such as motorcycles, snowmobiles, and pleasure motor boats that are covered by other SAE Standards or Recommended Practices. This SAE Recommended Practice may also be used when measuring the maximum exterior sound level on similar equipment powered by electricity or other power sources.
This recommended practice is intended to serve as a design verification procedure and not a product qualification procedure. It may be used to verify design specifications or vendor claims. Test procedures, methods and definitions for the performance of the fuel processor subsystem (FPS) of a fuel cell system (FCS) are provided. Fuel processor subsystems (FPS) include all components required in the conversion of input fuel and oxidizer into a hydrogen-rich product gas stream suitable for use in fuel cells. Performance of the fuel processor subsystem includes evaluating system energy inputs and useful outputs to determine fuel conversion efficiency and where applicable the overall thermal effectiveness. Each of these performance characterizations will be determined to an uncertainty of less than ± 2% of the value. The method allows for the evaluation of fuel processor subsystems for two general cases. Compare fuel processors with different designs (e.g., catalytic partial oxidation
This SAE Recommended Practice covers electric speedometer systems for general on-road (passenger car, multi-purpose passenger vehicle, truck, and bus) applications.
The purpose of this SAE Information Report is to provide information on refrigerant issues of concern to the mobile air-conditioning industry.
The purpose of this SAE Standard is to provide equipment specifications for CFC-12 (R-12) recovery for return to a refrigerant reclamation facility that will process it to the appropriate ARI Standard (Air Conditioning and Refrigerant Institute) or allow for recycling of the recovered refrigerant in equipment that is certified to meet the requirements of SAE J1991. Under the existing rule, the U.S. EPA requires refrigerant removed from a mobile air-conditioning (A/C) system using recovery equipment certified to meet SAE J2209 can only be recycled using equipment meeting SAE J1991 that is owned by the same company or individual. It is not acceptable that the refrigerant removed from a mobile A/C system, with this equipment, be directly returned to a mobile A/C system. This information applies to equipment used to service automobiles, light trucks, and other vehicles with similar CFC-12 (R-12) systems.
This user’s manual covers the instrumented arm for the Hybrid III 5th Percentile Small Female dummy as well as the SID –IIs dummy. It is intended for technicians and engineers who have an interest in assessing arm injury from the use of frontal and side impact airbags. It covers the construction, disassembly and reassembly, available instrumentation, and segment masses.
This SAE Aerospace Recommended Practice (ARP) covers visible surface defects on aerospace hose assemblies which have been installed and are functioning within a working environment at the time of visual inspection.
This SAE Recommended Practice defines the set-up and procedure for conducting the SAE Single Tooth Bending Fatigue Test. The details of the test fixture to be used (referred henceforth as “the test fixture” in this document) and gear test sample and the procedures for testing and analyzing the data are presented in this document.
This SAE Recommended Practice presents recommendations for test fuels and fluids that can be used to simulate real world fuels. The use of standardized test fluids is required in order to limit the variability found in commercial fuels and fluids. Commercial fuels can vary substantially between manufacturers, batches, seasons, and geographic location. Further, standardized test fluids are universally available and will promote consistent test results for materials testing. Therefore, this document: a Explains commercial automotive fuel components b Defines standardized components of materials test fluids c Defines a nomenclature for test fluids d Describes handling and usage of test fuels e Recommends fluids for testing fuel system materials The test fluid compositions specified in Section 7 of this document are recommended solely for evaluating materials. They are not intended for other activities, such as engine development, design verification, or process validation unless agreed
This SAE Recommended Practice establishes a method of evaluating the structural integrity of the parking brake system of all new trucks, buses, and combination vehicles designed for roadway use in the following classifications: TRACTOR, TRAILER, TRUCK, AND BUS: over 4500 kg (10 000 lb) GVWR.
This SAE Recommended Practice establishes dimensions for wheels for demountable rims, demountable rims, and rim spacers. The dimensions given are those necessary to maintain serviceability and interchangeability of the demountable rims, rim spacers, and wheels for demountable rims. Special and less common applications are not covered in this recommended practice.
The force, torque, and power methods of measurement are all in common use and should yield the same test results. Effects of steering, traction, surface texture, and non-steady-state tire operations are excluded from the recommended practice because they are still in the research stage.
This recommended practice contains dimensions and tolerances for spindles in the interface area. Interfacing components include axle spindle, bearing cones, bearing spacer, and seal. This recommended practice is intended for axles commonly used on Class 7 and 8 commercial vehicles. Included are SAE axle configurations FF, FL, I80, L, N, P, R, U, and W.
This SAE Information Report should be used as a supplement to SAE J1383 (Reference 2.1.1). It is intended to provide additional information which is important to the automotive designer and engineer in the process of designing, developing, and engineering the headlamps of motor vehicles which will take into account the effects of the aging process on the driver.
Items per page:
50
1 – 50 of 219709