Results
This SAE Standard establishes the test procedure, environment, and instrumentation for determining the sound levels of snowmobiles in the stationary test mode. This test method is intended to provide an accurate measurement of exhaust and other engine noise and may be used to evaluate new and in-use snowmobiles to determine compliance with noise control regulations. Sound level measurements obtained with this test method are not intended as an engineering determination of overall machine noise. For this purpose, the use of SAE J192 is recommended.
This specification covers an aluminum alloy in the form of welding wire.
This specification covers a mixture of liquid hydrocarbons and soluble additives.
SCOPE IS UNAVAILABLE.
This SAE Aerospace Recommended Practice (ARP) provides to the aerospace industry a procedure for the consistent and accurate calculation of fuel flow using turbine flowmeters during development, production, and post overhaul/repair gas turbine engine testing.
This SAE Aerospace Recommended Practice (ARP) contains methods used to measure the optical performance of airborne electronic flat panel display (FPD) systems. The methods described are specific to the direct view, liquid crystal matrix (x-y addressable) display technology used on aircraft flight decks. The focus of this document is on active matrix, liquid crystal displays (LCD). The majority of the procedures can be applied to other display technologies, however, it is cautioned that some techniques need to be tailored to different display technologies. The document covers monochrome and color LCD operation in the transmissive mode within the visual spectrum (the wavelength range of 380 to 780 nm). These procedures are adaptable to reflective and transflective displays paying special attention to the source illumination geometry. Photometric and colorimetric measurement procedures for airborne direct view CRT (cathode ray tube) displays are found in ARP1782. Optical measurement
This specification defines test methods and requirements for validation of solderless crimped connections. The purpose of this test is to simulate in the lab the stress seen in a typical life (15 years and 150000 miles) for a crimp connection and assure the crimp is mechanically strong and electrically stable. This specification was developed for use with stranded automotive copper wire. Only where specifically mentioned are other constructions or other core materials (aluminum, clad, steel core, etc.) applicable. This specification does not apply to wire types not mentioned, such as coaxial cable crimps, unless a USCAR-21 test is specifically referenced in the test specification for that wire type. This specification is based on accepted levels of environmental exposure for automotive applications. In any intended vehicle application, if the products covered by this specification are or may be subjected to conditions beyond those described in this document, they must pass special
This specification covers an aircraft-quality, low-alloy steel in the form of bars, forgings, mechanical tubing, and forging stock.
This SAE Recommended Practice is part of the SAE J2534-2/X_0500 set of documents that extends the SAE J2534-1_0500 API (version 05.00) specification, and defines how to implement fault-tolerant CAN (FT CAN) within the SAE J2534 API framework. This document details only the changes from SAE J2534-1_0500 and items not specifically detailed in this document are assumed to have not changed. An SAE J2534-2/8_0500 interface shall be compliant to fault-tolerant CAN (FT CAN) feature only when all the required functionality in this SAE Recommended Practice is implemented. Any functionality not required for compliance will be specifically marked as “optional” in this document. This document must be used in conjunction with the SAE J2534-2/BA_0500 and SAE J2534-2/RE_0500 documents.
This specification covers an aircraft-quality, low-alloy steel in the form of mechanical tubing.
This guideline is applicable to existing lead solder production products that will change to lead-free solder processes to meet the ELV Directive 2000/53/EC Annex II, exemption 8B requirements. This guideline is applicable to similar products used by multiple OEM's that have the same manufacturing processes / equipment. The intent is to streamline the supplier’s environmental testing via common qualification to reduce timing, quantities, and costs.
This specification covers a premium aircraft-quality alloy steel in the form of welding wire.
This specification establishes requirements for steel forgings of any shape or form from which finished parts are to be made (See 8.2, 8.3, & 8.4). This specification covers steel forgings suitable for use in the construction of aircraft/aerospace equipment
This interface standard applies to fuzes used in airborne weapons that use a 3-in fuze well. It defines: Physical envelope of the fuze well at the interface with the fuze. Load bearing surfaces of the fuze well. Physical envelope of the fuze and its connector. Mechanical features (e.g., clocking feature). Connector type, size, location and orientation. Retaining ring and its mechanical features (e.g., thread, tool interface). Physical envelope of the retaining ring at the interface with the fuze. Physical space available for installation tools. Torque that the installation tool shall be capable of providing. This standard does not address: Materials used or their properties. Protective finish. Physical environment of the weapon. Explosive interface or features (e.g., insensitive munitions (IM) mitigation). Charging tube. Torque on the retaining ring or loads on the load bearing surfaces. Each fuze and weapon combination should be evaluated to ensure that the weapon system will satisfy
This specification covers a premium aircraft quality, low-alloy steel in the form of bars, forgings, mechanical tubing, and forging stock.
The scope of this document is to aid in the selection of hose and hose assembly titles.
This SAE Information Report is the listing of recommendations for the proper packaging, storage, and shelf life limitations of new and unused hydraulic brake hose assemblies. The document embodies the testing, analysis, and experience of many users and manufacturers. Where specific manufacturer's recommendations are made, those recommendations shall supersede the recommendations of this document. This document describes the successful procedures and practices associated with brake hose assemblies usage by a wide cross section of manufacturers and users over several years. The practices are expected to be applicable to all brake hose assemblies which qualify under SAE J1401.
This specification covers the requirements for self-sealing, quick-disconnect couplings for fuel and oil system components.
This standard establishes the dimensional and visual quality requirements, lot requirements, and packaging and labeling requirements for O-rings molded from AMS7273 rubber. It shall be used for procurement purposes.
This interface standard applies to fuzes/fuzing systems (referred to as fuzing system hereafter) in airborne weapons that use a MIL-STD-1760 type interface. It defines the powers, the discrete signals and the serial data interface for the communications at the interface between the fuzing system and the remainder of the weapon, including the weapon control unit. The Class 1 interface is an electrical only interface that facilitates use of MIL-STD-1760 type platform store interfaces for the fuze to monitor intentional release and defines the fuze interface bus communications protocol to allow sending and receiving data from fuzing systems. Class 2 interfaces add a defined connector and additional interfaces to facilitate the exchange of compatible fuzing systems. Class 3 interfaces add further interface definitions to facilitate the exchange of AS5680A compatible fuzing systems components. The bus communications protocol provides a means by which the weapon may set mission parameters
This specification, in conjunction with the general requirements for steel heat treatment in AMS2759, establishes requirements for thermal stress-relief treatments of parts manufactured from the following materials: a Carbon and low-alloy steels b Tool steels c Precipitation-hardening, corrosion-resistant, and maraging steels d Austenitic corrosion-resistant steels e Martensitic corrosion-resistant steels
This specification covers steel forgings suitable for use in the construction of aircraft/aerospace equipment, special ordnance, and related accessories.
This document establishes the requirements for the sequencing of processes relating to parts fabricated from 300M or 4340 modified steel heat treated to, or to be heat treated to, 270,000 psi (1860 MPa) minimum ultimate tensile strength (UTS) and higher.
This specification covers an aircraft-quality, low-alloy steel in the form of sheet, strip, and plate.
This specification covers a premium aircraft-quality, low-alloy steel in the form of bars, forgings, mechanical tubing, and forging stock.
Items per page:
50
1 – 50 of 220040