Results
This AIR provides information about the specific requirements for missile hydraulic pumps and their associated power sources.
This test method outlines a standard procedure for performing cyclic reversing load testing on oscillating sliding bearings. The wear data from these tests is to be used for qualification requirements and to establish bearing design criteria.
This SAE Standard establishes the minimum construction and performance requirements for seven conductor 1/8-2/10-4/12 cable for use on trucks, trailers, and converter dollies for 12 VDC nominal applications. Where appropriate, the standard refers to two types of cables (Type F and S, described later in the standard), due to the variation in the performance demands of cables used in flexing and stationary applications. While the document’s title refers to ABS Power to differentiate the document from the SAE J1067 standard that it supersedes, the scope applies to both the primary green cable for powering ABS and lighting and the yellow auxiliary cable of the same construction.
This SAE Standard establishes the minimum performance requirements for electrical distribution systems for use in dollies and trailers in single or multiple configurations for 12 VDC nominal applications.
This SAE Recommended Practice specifies the design and/or evaluation with the specific equipment, conditions, and methods for distributorless battery ignition systems intended for use in various internal combustion engines including automotive, marine, motorcycle, and utility engine applications. The test procedures listed in this document are limited to measurements performed on a test bench only and do not include measurements made directly on engines or vehicles. This standard is not intended to supply information for battery ignition systems used in aircraft applications of any type.
This standard specifies the system requirements for an on-board vehicle-to-vehicle (V2V) safety communications system for light vehicles1, including standards profiles, functional requirements, and performance requirements. The system is capable of transmitting and receiving the SAE J2735-defined basic safety message (BSM) [1] over a dedicated short range communications (DSRC) wireless communications link as defined in the Institute of Electrical and Electronics Engineers (IEEE) 1609 suite and IEEE 802.11 standards [2] to [6].
This report revises ARD50015 document to the AIR format. This report, as was the original, is intended to complement ARP1420C and AIR1419C documents issued by the SAE S-16 Committee on spatial total-pressure distortion. These previous documents addressed only total-pressure distortion and excluded total temperature distortion. The subject of inlet total temperature distortion is addressed in this report with some background and identification of the problem area. The status of past efforts is reviewed, and an attempt is made to define where we are today. Deficiencies, voids, and limitations in knowledge and test techniques for total temperature distortion are identified.
This specification covers four series of electrical connectors (plugs and receptacles) with removable crimp contacts and accessories (see 6.1). AS81511 connectors are not recommended for new design. All AS81511 detail sheets that specified class D and/or H have been cancelled without replacement, therefore all class D and H requirements have been deleted from this specification. Electrical, mechanical and environmental features of these connectors include: Environment resisting at sea level and high altitude. Quick disconnect. RFI/EMI (Radio Frequency Interference/Electromagnetic Interference) protection (includes shell to shell grounding spring members). High density insert arrangements. Low level circuit capabilities. Scoop-proof. Fluid resistant class provided. High temperature class provided. Several voltage service ratings available. Individual contact release from the rear of the connector (series 3 and 4 only).
This specification covers an aircraft-quality, low-alloy steel in the form of seamless tubing.
This specification covers a low-alloy steel in the form of welding wire. Type 2 - copper coated wire was removed from this document (see 8.4).
This specification covers materials in the form of a liquid used to remove smut from aluminum surfaces treated with etch-type oxidation and corrosion removers.
This standard specifies the communications hardware and software requirements for fueling hydrogen surface vehicles (HSV), such as fuel cell vehicles, but may also be used where appropriate with heavy-duty vehicles (e.g., buses) and industrial trucks (e.g., forklifts) with compressed hydrogen storage. It contains a description of the communications hardware and communications protocol that may be used to refuel the HSV. The intent of this standard is to enable harmonized development and implementation of the hydrogen fueling interfaces. This standard is intended to be used in conjunction with the hydrogen fueling protocols in SAE J2601 and nozzles and receptacles conforming with SAE J2600 and ISO 17628. It may also be used with future hydrogen fueling protocols at the discretion of those fueling protocols.
This specification covers a beryllium aluminum alloy in the form of investment castings.
This document provides vehicle-level data collection, data analysis, and data verification procedures that may be used to verify that an instrument under test (IUT) satisfies the vehicle-level requirements specified in the SAE International (SAE) J2945/1 standard. For the purposes of this recommended practice, “vehicle-level requirements” primarily consist of those requirements which can be verified external to the vehicle. The IUT for these procedures is a configured dedicated short range communications (DSRC) vehicle-to-vehicle (V2V) device as defined in SAE J2945/1 and is installed on a light vehicle. While the IUT is conceptually separated from the vehicle it is installed on, the tests outlined in this document are primarily vehicle-level so the terms “vehicle” and “IUT” can generally be considered interchangeable. Additionally, non-vehicle-level complementary tests, not included in this document, are required to verify that the entire set of requirements specified in SAE J2945/1
This specification covers piston rings fabricated from cast iron.
This SAE Recommended Practice provides a system for marking thermoset rubber parts to designate the general type of material from which the part was fabricated.
This specification covers crimp-style aluminum lug terminals and conductor splices for aluminum aircraft wire. Lug terminals and conductor splices are hereafter called “terminals.”
This specification covers a chemically or mechanically expanded polyether urethane (EU) elastomeric foam material in the form of ready-to-use sheet.
This specification covers a chemically or mechanically expanded polyether urethane (EU) elastomeric foam material in the form of ready-to-use sheet.
This specification covers the specific requirements for aluminum alloy 7075 bar, rod, shapes, tube, and wire produced by extrusion.
This specification covers one type of thermoplastic, polysulfone resin-impregnated carbon fibers in the form of tape or sheet.
This specification covers one weight and one weave of nylon cloth.
This specification covers a fluorocarbon (FKM) rubber stock in the form of molded test slabs.
This document is offered to provide state-of-the-art information about design factors that must be considered in the design of new or significantly modified engine test cells used to test propeller equipped turboprop engines in either QEC or bare engine configurations. The report does not address design considerations for test cells designed to test turboprop engines with dynamometer type load absorption devices because they are essentially tested as turboshaft engines. Design considerations for those test cells are presented in AIR4989, Reference 2.1.
Items per page:
50
1 – 50 of 215879