Results
This AIR provides information about the specific requirements for missile hydraulic pumps and their associated power sources.
This specification covers an aluminum alloy in the form of rolled or forged rings up to 6 inches (152 mm), inclusive, in thickness (see 3.3.1.1.1) and an OD to wall thickness ratio of 10 or greater (see 8.5).
This specification covers a nitriding grade of premium aircraft-quality, low-alloy steel in the form of bars, forgings, mechanical tubing, and forging stock. AMS6496 and AMS6497 cover UNS K23280 with other quality levels.
This specification covers a magnesium alloy in the form of investment castings (see 8.6).
This specification covers a copper-zinc alloy (brass) in the form of sheet, strip, and plate (see 8.6).
This specification covers an aluminum alloy in the form of sheet from 0.063 to 0.249 inch (1.60 to 6.30 mm) in nominal thickness (see 8.6).
This SAE Recommend Practice establishes for passenger cars, light trucks, and multipurpose vehicles with GVW of 4500 kg (10000 pounds) or less, as defined by the EPA, and M1 category vehicles, as defined by the European Commission:
This specification covers a low-alloy steel in the form of sheet, strip, and plate 4.00 inches (101.6 mm) and under in thickness.
This SAE Aerospace Recommended Practice (ARP) provides the user with standardized guidelines for the measurement of effective intensity of short pulse width strobe anticollision lights for aircraft in the laboratory, in maintenance facilities, and in the field. A common source of traceability for calibration of the measurement systems, compensation for known causes of variation in light output such as the use of colored lenses, and recommendations which minimize sources of errors and uncertainties are included in this document. Estimates of uncertainty and error sources for each class of measurement are discussed.
This specification covers a magnesium alloy in the form of investment castings (see 8.6).
This procedure describes a method of measuring the resistance to wet color transfer of materials such as textiles, leather, and composites.
The published SAE J2954 standard established an industry-wide specification that defines acceptable criteria for interoperability, electromagnetic compatibility, EMF, minimum performance, safety, and testing for wireless power transfer (WPT) for light-duty plug-in electric vehicles. This SAE Information Report, SAE J2954/2, defines new power transfer levels in the higher power ranges needed for heavy-duty electric vehicles. This document addresses the requirements based on these charge levels and different vehicle applications as a first step in the process of completing a standard that the industry can use, both for private (fleet) and public wireless power transfer, including for charging electric vehicle batteries. This document is the first step in a process towards HD static and dynamic WPT. This document lacks specific requirements and solutions, for which field data is needed. This document is not intended to be a guideline to enable manufacturers to design systems with minimal
This SAE Recommended Practice provides test procedures, requirements, and guidelines for the system of optical warning devices used on emergency vehicles.
This SAE Standard provides test procedures, requirements, and guidelines for motorcycle turn signal lamps. It does not apply to mopeds.
This SAE Information Report J2931/6 establishes the requirements for physical and data link layer communications between Plug-in Electric Vehicles (PEV) and the Electric Vehicle Supply Equipment (EVSE).
This SAE Standard establishes test methods for the evaluation of devices and equipment in vehicles against transient transmission by coupling via lines other than the power supply lines. The test methods demonstrates the immunity of the instrument, device, or equipment to coupled fast transient disturbances, such as those caused by switching of inductive loads, relay contact bouncing, etc. Four test methods are presented in SAE J1113-12: the capacitive coupling clamp (CCC) method the direct capacitive coupling (DCC) method the inductive coupling clamp (ICC) method the capacitive/inductive coupling (CIC) method
This SAE Standard defines and provides a means for the control of colors employed in motor vehicle external lighting equipment, including lamps and reflex reflectors. The document applies to the overall effective color of light emitted by the device in any given direction, and not to the color of the light from a small area of the lens. It does not apply to pilot, indicator, or tell-tale lights.
This SAE Recommended Practice provides minimum performance target and uniform laboratory procedures for fatigue testing of wheels and demountable rims intended for normal highway use on trucks, buses, truck-trailers, and multipurpose vehicles. Users may establish design criteria exceeding the minimum performance target for added confidence in a design. The cycle target noted in Tables 1 and 2 are based on Weibull statistics using two parameter, median ranks, 50% confidence level and 90% reliability, and beta equal to two, typically noted as B10C50. For other wheels intended for normal highway use and temporary use on passenger cars, light trucks, and multipurpose vehicles, refer to SAE J328. For wheels used on trailers drawn by passenger cars, light trucks, or multipurpose vehicles, refer to SAE J1204. For bolt together military wheels, refer to SAE J1992. This document does not cover other special application wheels and rims.
This SAE Standard covers the general requirements and the test requirements for a flashing warning lamp for agricultural equipment.
This specification covers one type of epoxy-resin-impregnated organic fibers in the form of woven cloth.
This specification covers one type of polyether-type urethane (EU) resin and hardener which, when mixed and cured, produce elastomeric polyurethane products.
This specification covers one type of epoxy-resin-impregnated organic fibers in the form of woven cloth.
This specification covers one type of organic fiber in the form of roving. The product shall be formed as four ends of 1140 denier (1270 d tex) yarn (AMS3901/3) collected into an approximately parallel arrangement without twist.
This specifications covers thirteen classes of para-aramid tape and webbing of a single width and with varying weights.
This specification covers one type of organic (para-aramid) fiber in the form of yarn. The product shall be formed as a multiplicity of filaments drawn together and gathered into an approximately parallel arrangement.
This specification covers thermal radiation resistant material in the form of tape with pressure-sensitive adhesive.
This specification covers one type of organic fiber in the form of yarn. The product shall be formed as a multiplicity of filaments drawn together and gathered into an approximately parallel arrangement.
This specification covers the requirements for an aluminum brazing flux in granular form.
This specification covers one type of epoxy-resin-impregnated organic fibers in the form of woven cloth.
This specification covers one class of para-aramid tape and webbing of a single width and with varying weights.
This specification covers methyl alcohol in the form of a liquid.
This specification covers an unfilled, room-temperature-polymerizing epoxy resin formulation with a polyamide hardener, supplied as a two-component system.
This specification covers one type of epoxy-resin-impregnated carbon fibers in the form of tape and sheet.
This specification covers one type of nylon in the form of webbing.
This specification covers one type of organic fiber in the form of roving. The product shall be formed as three ends of 2840 (3160 d tex) denier yarn (AMS3901/14) collected into an approximately parallel arrangement without twist.
This specification covers one type of epoxy-resin-impregnated organic fibers in the form of woven cloth.
This specification covers the specific requirements for seamless tube drawn from aluminum alloy 6061.
This specification covers three classes of para-aramid tape and webbing of a single width and with varying weights.
This specification covers one type of epoxy-resin-impregnated carbon fibers in the form of tape and sheet.
This specification covers one type of organic fiber in the form of yarn. The product shall be formed as a multiplicity of filaments drawn together and gathered into an approximately parallel arrangement.
This SAE Recommended Practice pertains to electrical systems of motorcycles both with and without batteries.
This specification covers one width and strength of nylon tape.
This specification covers three classes of para-aramid tape and webbing of a single width and with varying weights.
Items per page:
50
1 – 50 of 216072