Results
This document defines the test procedures and performance limits of steady state and transient voltage characteristics for 12 V, 24 V, or 48 V electrical power generating systems used in commercial ground vehicles.
SAE J448, Surface Texture, has been set up for precision reference specimens using a controlled surface profile to obtain reproducible roughness values. These specimens are for instrument calibration. Appropriate symbols for roughness, waviness, and lay have also been standardized (ASA B46.1-1962 and SAE J448). For production control, especially from one geographical location to another, means are required to facilitate the inspection of surface characteristics called for by specifications which include not only roughness but profile waviness and lay. In order to integrate the requirements of the designer with the actual production of surfaces, a second grade of control standards must be adopted which will be functional in nature for the specific product being manufactured. These control standards may be Calibrated Pilot Specimens (actual parts with satisfactory texture) or Roughness Comparison Specimens (ASA B46.1-1962). This SAE Recommended Practice describes the usage of these
This SAE Recommended Practice establishes methods to determine grade parking performance with respect to: a Ability of the parking brake system to lock the braked wheels. b The trailer holding or sliding on the grade, fully loaded, or unloaded. c Applied manual effort. d Unburnished or burnished brake lining friction conditions. e Down and upgrade directions.
The purpose of this SAE Recommended Practice is to describe the terms yield strength and yield point. Included are definitions for both terms and recommendations for their use and application.
This SAE Aerospace Standard (AS) defines the requirements for a heavy-duty polytetrafluoroethylene (PTFE) lined, metallic reinforced, hose assembly suitable for use in high temperature, high pressure, 4000 psi, aircraft and missile hydraulic fluid systems.
This specification covers a premium aircraft-quality, low-alloy steel in the form of bars, forgings, and forging stock.
This SAE Aerospace Information Report (AIR) provides data and general analysis methods for calculation of internal and external, pressurized and unpressurized airplane compartment pressures during rapid discharge of cabin pressure. References to the applicable current FAA and EASA rules and advisory material are provided. While rules and interpretations can be expected to evolve, numerous airplanes have been approved under current and past rules that will have a continuing need for analysis of production and field modifications, alterations and repairs. The data and basic principles provided by this report are adaptable to any compartment decompression analysis requirement.
The Gauge Evaluation Procedure Task Force was formed by the Non-Hydraulic Hose Committee to develop a gauge evaluation procedure to be used when evaluating the capability of gauges used for hose measurement. The use of a standard method for gauge evaluation will help users easily compare equipment capability. The information provided in this recommendation is based on the methods used to produce the data presented in SAE J1759 and J2605.
This Aerospace Information Report (AIR) outlines the design considerations and criteria for the control of water carryover from the environmental control system (ECS) with respect to causes and indicated corrective or preventative action. In addition, condensation on structure will be reviewed with possible preventative action described.
The test procedure per the applicable Engine Manual does require a vibration check for the low/intermediate and high speed rotor systems. Release of an engine with high vibrations can result in: On-wing vibration complaints, with subsequent troubleshooting Rotor system failures Premature engine removals Limits are provided for transient conditions and steady state data points. Troubleshooting recommendations are limited to verification of the proper signal input and tracking. This practice provides recommendations for: Correct cable and transmitter installation and connections Calibration Recorded data interpretation and data analysis
This standard covers the requirements for non-separable, airframe antifriction needle bearings and corrosion-resistant and traditional materials intended for use in flight vehicle control systems with radial loads.
A recommended pilot-system integration (i.e., crew interface and system integration) approach for concept development is described in Figure 1. The approach emphasizes the fundamental need for a top-down design methodology with particular focus on clear operational performance requirements and functional integration. While this document is primarily aimed at aircraft systems design and integration, the methodology is applicable to a wide range of design and integration situations. It is derived from well established human factors engineering design principles.
This specification covers continuous, multiple-strand, roving of Type "S-2" glass impregnated with a heat-curable epoxy resin matrix and processed to a "B" stage condition.
This SAE Recommended Practice is part of the SAE J2534-2/X_0500 set of documents that extends the SAE J2534-1_0500 API (version 05.00) specification. It defines the common data structures and constants that will be used to implement the extension to the SAE J2534 API. This document will only include the items that are used by the V05.00 API and that are NOT included in SAE J2534-1_0500. It will not include items from older API versions unless they are used by the V05.00 API.
This specification covers the general requirements for red and white individual instrument lights. This document has been streamlined. Appendix A to MIL-L-5057F lists those documents required for MIL-L-5057F acquisition and is a mandatory part of MIL-L-5057F. Those documents listed in Appendix A have the same status as those referenced directly in MIL-L-5057F (first tier documents). All other documents, referenced through tiering, may be used as guidance and information to supplement MIL-L-5057F. This document’s scope is limited to lamp source designs solely. Furthermore, the use of red lighting should not be considered for new design and included within this document to support requirements for existing military aircraft that still operate with this system of lighting.
SCOPE IS UNAVAILABLE.
This Aerospace Recommended Practice (ARP) provides recommendations for the design and test requirements for a hydraulic thermal relief valve. The thermal relief valve is intended for use in a civil or military aircraft hydraulic system with a rated system pressure up to 5000 psi (34500 kPa).
Items per page:
50
1 – 50 of 221567