Results
This AIR provides information about the specific requirements for missile hydraulic pumps and their associated power sources.
This SAE Recommended Practice applies to functions of motor vehicle signalling and marking lighting devices which use light emitting diodes (L.E.D.’s) as light sources. This report provides test methods, requirements, and guidelines applicable to the special characteristics of L.E.D. lighting devices. This Recommended Practice is in addition to those required for devices designed with incandescent light sources. This report is intended to be a guide to standard practice and is subject to change to reflect additional experience and technical advances.
This document addresses robustness of electrical/electronic modules for use in automotive applications. Where practical, methods of extrinsic reliability detection and prevention will also be addressed. This document primarily deals with electrical/electronic modules (EEMs), but can easily be adapted for use on mechatronics, sensors, actuators and switches. EEM qualification is the main scope of this document. Other procedures addressing random failures are specifically addressed in the CPI (Component Process Interaction) section 10. This document is to be used within the context of the Zero Defect concept for component manufacturing and product use. It is recommended that the robustness of semiconductor devices and other components used in the EEM be assured using SAE J1879 OCT2007, Handbook for Robustness Validation of Semiconductor Devices in Automotive Applications. The emphasis of this document is on hardware and manufacturing failure mechanisms, however, other contemporary issues
This standard covers low voltage primary cable intended for use at a nominal system voltage of 60 V DC (25 V AC) or less in surface vehicle electrical systems. The tests are intended to qualify cables for normal applications with limited exposure to fluids and physical abuse.
This engineering design specification provides design parameters and general requirements for School Bus Stop Arms equipped with alternately flashing lights. The stop arm is intended as an optional device which may be used in addition to, but not as a substitute for, school bus signal lamps covered by SAE J887(July, 1964). Decision for adoption of the recommendations presented in the Appendix is left to governmental units or other bodies who adopt this practice.
This SAE Standard provides installation requirements, test procedures, design guidelines, and performance requirements for backup/reversing lamps.
This SAE Recommended Practice provides test procedures, requirements, and guidelines for rear cornering lamps for use on vehicles less than 9.1 m in overall length.
This SAE Recommended Practice is intended as a guide toward standard practice and is subject to change to keep pace with experience and technical advances. This document provides standardized laboratory tests, test methods and equipment, and requirements for lighting devices covered by SAE Recommended Practices and Standards. It is intended for devices used on vehicles less than 2032 mm in width. Tests for vehicles larger than 2032 mm in overall width are covered in SAE J2139. Device specific tests and requirements can be found in applicable SAE technical reports.
This SAE Standard establishes minimum requirements for lighting and marking earthmoving construction machinery as defined in SAE J1116, 1.1 Self-Propelled Construction Machines—Earthmoving (excluding excavators). (Construction machinery is normally operated off-highway, and therefore this SAE document is not intended to be used as a basis for regulations by those having authority over on-highway motor vehicles.)
SCOPE IS NOT AVAILABLE.
This specification covers two types of thickened, water base temporary coating remover in the form of an alkaline liquid.
This SAE Recommended Practice provides for common test and verification methods to determine lead acid and nickel metal hydride electric vehicle battery module performance. The document creates the necessary performance tests to determine (a) what the basic performance of EV battery modules is, and (b) if battery modules meet minimum performance specification established by vehicle manufacturers or other purchasers. Specific values for these minimum performance specifications are not a part of this document.
This SAE Recommended Practice provides procedures and information to conduct vibration (impact) tests on lighting devices and their components as well as other safety equipment used on vehicles.
This SAE Standard provides test procedures, requirements, and guidelines for tail lamps (rear position lamps) intended for use on vehicles of less than, equal to, or greater than 2032 mm in overall width.
This SAE Recommended Practice provides test procedures, requirements, and guidelines for side turn signal lamps intended for use on vehicles 12 m or more in overall length, except pole trailers. Side turn signal lamps conforming to the requirements of this document may be used on other large vehicles such as trucks, truck tractors, buses, and other applications where this type of lighting device is desirable. It is not intended for use on shorter vehicles due to the higher intensity requirements of SAE J2039 compared to the SAE J914 devices.
This document provides design guidelines, test procedure references, and performance requirements for directional, single color, flashing optical warning devices used on authorized emergency, maintenance, and service vehicles. It is intended to apply to, but is not limited to, surface land vehicles.
This SAE Standard provides the minimum requirements for primary and auxiliary jumper cable plug and receptacle for the truck-trailer and converter dolly jumper cable systems for 12 VDC nominal applications. It includes the test procedures, design, and performance requirements.
This SAE Standard describes snowmobile and snowmobile cutter requirements for the installation of lamps, reflective devices, and associated equipment.
This SAE Recommended Practice provides test procedures, performance requirements, and guidelines for cleaners intended for use on motor vehicles.
This SAE Recommended Practice applies to motor vehicle signaling and marking devices which use light generated by a discharge source. This document provides test methods, requirements, and guidelines applicable to the unique characteristics of discharge lighting systems and their components. These are in addition to those required for signal and marking devices. This document is intended to be a guide to standard practice and is subject to change to reflect additional experience and technical advances.
This SAE Recommended Practice provides test procedures, requirements, and guidelines for rear cornering lamps for use on vehicles less than 9.1 m in overall length.
This SAE Recommended Practice provides test procedures, performance requirements, and guidelines for cargo lamps intended for use on vehicles under 5443 kg (12000 pounds) Gross Vehicle Weight Rating (GVWR).
This SAE Standard covers unshielded cable, 22 gauge and larger, intended for use at a nominal system voltage up to 600 V or 1000 V (ACrms or DC). It is intended for use in surface vehicle electrical systems.
This SAE Recommended Practice applies to retroreflective sheeting materials that are used on truck tractors and trailers 2032 mm or more in overall width and with a gross vehicle weight rating (GVWR) over 4536 kg and school buses to improve vehicle conspicuity. The retroreflective sheeting materials for the truck tractors and trailers are super-high-intensity materials containing microprisms. The retroreflective sheeting materials for school buses may contain flexible non-exposed glass bead lenses or microprisms.
This SAE Standard outlines general procedures for the grounding of electrical components in 12- and 24-V systems, intended for light and heavy-duty on-highway trucks and their trailers; and off-road machinery applications as described in SAE J1116.
The purpose of this document is to provide performance requirements for hydrogen dispensing systems used for fueling 35 MPa heavy duty hydrogen transit buses and vehicles (other pressures are optional). This document establishes the boundary conditions for safe heavy duty hydrogen surface vehicle fueling, such as safety limits and performance requirements for gaseous hydrogen fuel dispensers used to fuel hydrogen transit buses. For fueling light-duty vehicles SAE J2601 should be used. SAE J2601-2 is a performance based protocol document that also provides guidance to fueling system builders, manufacturers of gaseous hydrogen powered heavy duty transit buses, and operators of the hydrogen powered vehicle fleet(s). This fueling protocol is suitable for heavy duty vehicles with a combined vehicle CHSS capacity larger than 10 kilograms aiming to support all practical capacities of transit buses. It is non-prescriptive in how to achieve a full fill or 100% state of charge (SOC) in the
This SAE Standard describes alternator physical, performance, and application requirements for heavy-duty electrical charging systems for off-road work machines, including those defined in SAE J1116.
This SAE Standard was developed to provide a method for indicating the direction of engine rotation and numbering of engine cylinders. The document is intended for use in designing new engines to eliminate the differences which presently exist in industry.
This SAE Recommended Practice is intended to describe the application of single-phase DC to AC inverters, and bidirectional inverter/chargers, which supply power to ac loads in Class heavy duty on-highway trucks (10K GVW). The document identifies appropriate operating performance requirements and adds some insight into inverter selection. This document applies to factory and after-market installed DC-to-AC inverter systems (Including inverter chargers) providing up 3000 W of 120 VAC line-voltage power as a convenience for operator and passenger use. Such inverters are intended to power user loads not essential to vehicle Operation or safety (e.g., HVAC, TV, microwave ovens, battery chargers for mobile phones or laptop computers, audio equipment, etc.). Systems incorporate the inverter itself as well as the input, output, control, and signal wiring associated with the inverter. Requirements are given for the performance, safety, reliability, and environmental compatibility of the system
SAE J2601-4 establishes process limits for ambient temperature hydrogen fueling of light-duty automotive vehicles, passenger cars, and trucks that use a compressed hydrogen storage system (CHSS) that meets SAE J2579, where ambient temperature hydrogen fueling is defined as a fueling event where the fuel delivery temperature is greater (e.g., warmer) than the precooled requirements of SAE J2601. Table 1 depicts the scope of SAE J2601-4 and potential work items for future revisions within this or other documents of the SAE J2601 series. SAE J2601 includes protocols that are applicable for two pressure classes (35 MPa and 70 MPa), three fuel delivery temperature categories (-40 °C, -30 °C, and -20 °C) and CHSS sizes from 49.7 to 248.6 L. Future versions of SAE J2601 may incorporate warmer fuel delivery temperatures (-10 °C and ambient) and smaller compressed hydrogen storage systems for motorcycles and other light-duty applications. Fueling protocols should be developed based on a set of
This glossary is intended to provide engineers, metallurgists, and production personnel with uniform definitions of commonly used carbon sheet and strip terms. The glossary serves to supplement information and photographs reported in SAE J810, J763, J877, J863, and J403. Many of the terms listed apply only to hot-dipped zinc-coated products or to uncoated products. The letter C following the term identifies a term applying to coated materials, while the letters NC identify a term applying to uncoated materials. Where no identification is provided, the term is common to both.
This information report provides a short glossary of rocket ignition and related terms.
This document provides an overview on how and why EGR coolers are utilized, defines commonly used nomenclature, discusses design issues and trade-offs, and identifies common failure modes. The reintroduction of selectively cooled exhaust gas into the combustion chamber is just one component of the emission control strategy for internal combustion (IC) engines, both diesel and gasoline, and is useful in reducing exhaust port emission of nitrogen oxides (NOx). Other means of reducing NOx exhaust port emissions are briefly mentioned, but beyond the scope of this document.
This document presents a glossary of many terms found in literature related to aviation oxygen systems and associated topics. Such a listing can never be all inclusive, but the majority of important terms are anticipated to be included for reference.
This specification covers an aluminum alloy in the form of sheet, clad on two sides.
This specification covers an aluminum alloy in the form of bars and rods 0.500 to 8.000 inches (12.7 to 203.2 mm) in nominal diameter or least difference between parallel sides and up to 50 square inches (322.6 cm2) in cross-sectional area (see 8.6).
The thermocouple design recommended herein is presented as one for which the correction to the observed emf, because of thermal conduction along the stem and wires, is within the limits presented in the accompanying figure. On referring to the figure, it is seen that no restriction is placed upon the diameter of the thermocouple or stem, and the longitudinal dimensions are expressed in terms of wire and stem diameters. The type of stem, such as packed ceramic stock, refractory insulating tubing, etc., also is left open to choice. Thus the sizes of wires and supporting stems may be varied over wide ranges to match particular requirements where conduction errors are to be limited or controlled.
This SAE Standard is intended to describe the basic types of felling heads, including those with bunching capabilities, that are attachments to a self-propelled machine. Only the major components that are necessary to describe the functions of the felling head, and to apply the principles of the standard are included. Illustrations used are not intended to include all existing felling heads or to describe any particular manufacturer’s variation.
Items per page:
50
1 – 50 of 219487