Results
This test method provides a procedure for measuring no-load rotational breakaway torque of self-lubricating spherical bearings.
The primary objective of this recommended practice is to confirm that vehicles can communicate a minimum set of information in accordance with diagnostic test services specified in SAE J1979-2, or the equivalent ISO 14229-1:2013 (Ed. 2) and SAE J1979-3 documents. A successful result using the SAE J1699-5 Automotive Alliance for Innovation (AAI) software for OBD-II testing indicates that the main aspects of UDS communication have been examined, but it does not provide assurance of complete compliance with all aspects of SAE J1979-2 or SAE J1979-3. SAE J1699-5 tests run with a SAE J2534 device hardware and API that is not fully compliant will result in a test failure. This specification takes precedence over all conflicts in the documents cited in this section.
This SAE Information Report provides SAE’s recommendations for meeting the requirements for Real Emissions Assessment Logging (REAL) oxides of nitrogen (NOx) accuracy demonstration and for the implementation of REAL NOx binning requirements as defined in onboard diagnostics (OBD) regulations 13 CCR 1971.1 and 13 CCR 1968.2.
This specification covers a corrosion- and heat-resistant nickel alloy in the form of plate nominally 2.00 inches (50.8 mm) and under in thickness, inclusive.
This SAE Information Report establishes a uniform procedure for assuring the manufactured quality, installed utility, and performance of automotive remote steering controls other than those provided by the vehicle manufacturer (OEM). These products are intended to provide driving capability to persons with physical disabilities. The adaptive modifications seek to compensate for lost or reduced function in the extremities of the driver with a disability. Remote steering controls are designed to provide a steering input device alternative to the OEM steering wheel that either reduces the required input force, changes the required range of motion or changes the location of the steering control, or any combination of the above. These controls supplement by power, other than by the driver’s own muscular efforts, the force output of the driver with a disability. Because this is an Information Report, the numerical values for performance measurements presented in this report and in the
This SAE Aerospace Information Report (AIR) describes procedures for use in the field to determine if 115/200 Volt, 400 Hz aircraft external electrical power connectors are excessively worn, which may result in the inability of the external power plug to be retained, intermittent electrical performance, and arcing.
This specification covers pure gold in the form of wire 0.005 to 0.040 inch (0.012 to 1.000 mm), inclusive, in nominal diameter and ribbon 0.002 to 0.051 inch (0.05 to 1.28 mm), inclusive, in nominal thickness (see 8.5).
This specification covers a corrosion- and heat-resistant cobalt alloy in the form of bars, forgings, flash-welded rings, and stock for forging or flash-welded rings.
This Aerospace Recommended Practice (ARP) provides design philosophies, guidelines, requirements, and a set of recommended symbols, lines, and linear patterns for aeronautical information presented on electronic flight deck display devices. Specifically, this document addresses symbols, lines, and linear patterns historically seen on aeronautical charts. It provides recommended symbols for navigation aids, airspace boundaries, missed approach holding patterns, etc. The document does not address all aeronautical symbols, lines, or linear patterns, nor does it provide specific recommendations about color, text and fonts, line weight, or symbol size. Additionally, it does not provide recommendations for non-aeronautical symbols such as traffic or weather. The general guidelines, recommendations and requirements are intended to apply regardless of whether the display application is intended for IFR or VFR operations and regardless of the type of aircraft (14 CFR Part 23, 25, 27, or 29
The purpose of this document is to provide performance requirements for hydrogen dispensing systems used for fueling 35 MPa heavy duty hydrogen transit buses and vehicles (other pressures are optional). This document establishes the boundary conditions for safe heavy duty hydrogen surface vehicle fueling, such as safety limits and performance requirements for gaseous hydrogen fuel dispensers used to fuel hydrogen transit buses. For fueling light-duty vehicles SAE J2601 should be used. SAE J2601-2 is a performance based protocol document that also provides guidance to fueling system builders, manufacturers of gaseous hydrogen powered heavy duty transit buses, and operators of the hydrogen powered vehicle fleet(s). This fueling protocol is suitable for heavy duty vehicles with a combined vehicle CHSS capacity larger than 10 kilograms aiming to support all practical capacities of transit buses. It is non-prescriptive in how to achieve a full fill or 100% state of charge (SOC) in the
This specification defines limits of variation for determining acceptability of composition of cast and wrought corrosion and heat-resistant steels and alloys, maraging and other highly alloyed steels, and iron alloy parts and materials acquired from a producer.
This specification covers aluminum alloy sheet laminated with one or more layers of unidirectional aramid fiber/epoxy prepreg. The outer layers are always aluminum alloy.
The intended upper bound of this specification is that the particle size distribution (PSD) of powders supplied shall be <60 mesh (250 µm) and that no powder (0.0 wt%) greater than 40 mesh (425 µm) is allowed.
This specification covers aluminum in the form of sheet and plate.
AMS6885/5 is the Material Specification (MS) which defines the requirements of a unidirectional carbon fiber tape epoxy repair prepreg capable of curing under vacuum for repair of carbon fiber reinforced epoxy structures. It also defines the requirements of an epoxy film adhesive to be applied in a co-bonding process with the prepreg for solid laminate and sandwich bonding.
This specification covers a copper alloy (phosphor bronze) in the form of sheet, strip, and plate (see 8.6).
This SAE Aerospace Recommended Practice (ARP) provides guidance for the design and installation of a commercial aircraft hydraulic system to meet the applicable requirements, including the applicable airworthiness regulations that affect the hydraulic system design. This ARP also provides information and guidelines on the many factors that arise in the design process to provide cost effectiveness, reliability, maintainability and accepted design and installation practices.
This specification covers the requirements for equipment, materials and procedures to be used in anodic treatments for magnesium base alloys for the purpose of increasing their corrosion resistance or producing surfaces suitable for the application of a protective organic finish.
This SAE Aerospace Standard (AS) establishes the geometric control requirements for bolts, screws, and studs where worded notes and symbolized notes are used for straightness, concentricity, squareness, and runout.
This specification covers an aluminum alloy in the form of castings (see 8.10).
Items per page:
50
1 – 50 of 222741