Results
This AIR provides information about the specific requirements for missile hydraulic pumps and their associated power sources.
This Purchasing Specification, AMS6885/4, specifies the batch release and delivery requirements for film adhesive used for repair. This specification is applicable only when the film adhesive is used as part of the repair system defined in AMS6885 and AMS6885/1. This specification also defines the procedure and requirements for storage life extension of materials purchased against this specification. It is only applicable for materials qualified against AMS6885 (refer to PRI-QPL-AMS6885), and shall be carried out within the responsibility of the purchaser and under control of its Quality organisation.
This specification covers polythioether rubber fuel-resistant sealing compounds supplied as a two-component system that cures at room temperature.
This specification establishes requirements for chrome-free surface pretreatment materials used for surface preparation of metallic surfaces prior to applying organic coatings.
This FMEA standard describes potential failure mode and effects analysis in design (DFMEA), supplemental FMEA-MSR, and potential failure mode and effects analysis in manufacturing and assembly processes (PFMEA). It assists users in the identification and mitigation of risk by providing appropriate terms, requirements, rating charts, and worksheets. As a standard, this document contains requirements—”must”—and recommendations—”should”—to guide the user through the FMEA process. The FMEA process and documentation must comply with this standard as well as any corporate policy concerning this standard. Documented rationale and agreement with the customer are necessary for deviations in order to justify new work or changed methods during customer or third-party audit reviews.
The ice bath recommended herein is similar to that described in SAE AIR 46.* Some material not presented in AIR 46, including preferred dimensions, has been added.
This specification covers a premium aircraft-quality maraging steel in the form of bars and forgings, 0.50 to 8.00 inches (12.7 to 203.2 mm) in nominal diameter or least distance between parallel sides, and forging stock of any size.
This SAE Standard specifies the test requirements in addition to those given in ISO 3046-1 for determining the power, at a single point or as a power curve, of marine propulsion engines or systems for recreational craft and other small craft using similar propulsion equipment of less than 24 m length of the hull. It also provides the means for documenting and checking the declared (rated) power published by the manufacturer.
This document applies to off-road forestry work machines defined in SAE J1116 or ISO 6814.
The process detailed within this document is generic and applies to the entire end-to-end health management capability, covering both on-board and on-ground elements, in both commercial and military applications throughout their lifecycle. This ARP addresses a gap in guidance related to usage of ground-based health management equipment for airworthiness credit, ensuring a level of integrity commensurate with the potential aircraft-level consequences of the relevant failure conditions. The practical application of this standardized process is detailed in the form of a checklist. The on-board elements described here are typically the source of the data acquisition used for off-board analysis. The on-board aspects relating to airworthiness and/or safety of flight, e.g., pilot notification, are addressed by existing guidance and policy documents. If a proposed health management capability for airworthiness credit involves modification of the on-board systems, the substantiation of those
This standard defines a color index system used by, but not limited to, Government activities in a format suitable for color identification, color selection, color matching, and quality control inspection. It also describes the designation and use of color media that is available to conduct these activities. Use of the color index referenced in this standard is intended to promote standardization and consistency in the color of items produced for Government use. Color media is described as follows: Color Chip Representation, Fan Deck: Suitable for color identification and selection. Color Chip Representation, Color Book: Suitable for color identification and selection. Precise Color Matching, Individual Color Chips: Suitable for color matching and quality control inspection purposes. Precise Color Matching, Set of Color Chips: Suitable for color matching and quality control inspection purposes.
This specification establishes hardness and electrical conductivity acceptance criteria for finished or semifinished parts made from wrought aluminum alloys after heat treatment (see 8.6).
This SAE Aerospace Recommended Practice (ARP) document establishes criteria and recommended practices for the use of airborne icing tankers to aid in design and certification of aircraft ice protection systems and components. Several icing tankers are described, along with their capabilities and suggested use. Sample data for these tanker spray systems are included, shown with 14 CFR Parts 25 and 29, Appendix C icing envelopes for continuous maximum and intermittent maximum icing conditions. (Note: In the remainder of this document, the phrase “Appendix C icing envelopes” will be used for brevity.) This ARP is intended as a guide toward standard practice and is subject to change to keep pace with experience and technical advances.
AMS6885/5 is the Material Specification (MS) which defines the requirements of a unidirectional carbon fiber tape epoxy repair prepreg capable of curing under vacuum for repair of carbon fiber reinforced epoxy structures. It also defines the requirements of an epoxy film adhesive to be applied in a co-bonding process with the prepreg for solid laminate and sandwich bonding.
This Purchasing Specification, AMS6885/3, specifies the batch release and delivery requirements for unidirectional carbon fiber tape epoxy prepreg used for repair. This specification is applicable only when the unidirectional carbon fiber tape epoxy prepreg is used as part of the repair system defined in AMS6885 and AMS6885/1. This specification also defines the procedure and requirements for storage life extension of materials purchased against this specification. It is only applicable for materials qualified against AMS6885 (refer to PRI-QPL-AMS6885) and shall be carried out within the responsibility of the purchaser and under control of its Quality organisation.
This specification covers an aluminum alloy in the form of sheet and plate with a thickness of 0.125 to 0.499 inch (3.20 to 12.67 mm), inclusive (see 8.5).
This specification covers a low-carbon steel in the form of seamless tubing up to 5.50 inches (139.7 mm), nominal OD, inclusive.
The following schematic diagrams reflect various methods of illustrating automotive transmission arrangements. These have been developed to facilitate a clear understanding of the functional interrelations of the gearing, clutches, hydrodynamic drive unit, and other transmission components. Two variations of transmission diagrams are used: in neutral (clutches not applied) and in gear. For illustrative purposes, some typical transmissions are shown.
This data dictionary provides definitions for quantities, measurement units, reference systems, measurands, measurements, and quantity modalities commonly used in the command and control of cyber-physical systems. A cyber-physical system is an engineered system that is built from, and depends upon, the seamless integration of computational algorithms and physical components. Cyber-physical systems are often interconnected via data links and networks. The term encompasses intelligent vehicles and devices that operate in any environment, including robotic and autonomous systems.
The purpose of this SAE Recommended Practice is to establish a uniform laboratory procedure for securing and reporting the friction and wear characteristics of brake linings. The performance data obtained can be used for in-plant quality control by brake lining manufacturers and for the quality assessment of incoming shipments by the purchasers of brake linings.
This SAE Recommended Practice covers equipment capabilities and the test procedure to quantify and qualify the shear strength between the friction material and backing plate or brake shoe for automotive applications. This SAE Recommended Practice is applicable to: bonded drum brake linings; integrally molded disc brake pads; disc brake pads and backing plate assemblies using mechanical retention systems (MRS); coupons from drum brake shoes or disc brake pad assemblies. The test and its results are also useful for short, semi-quantitative verification of the bonding and molding process. This Recommended Practice is applicable during product and process development, product verification and quality control. This Recommended Practice does not replicate or predict actual vehicle performance or part durability.
This SAE Recommended Practice is intended to establish uniform procedures for developing specifications for automotive thermoplastics. It is intended for use by automotive companies and their suppliers of molded and/ or fabricated parts from thermoplastic materials.
This SAE Recommended Practice provides a system for classification and specification for limited number of polyamides (nylons) used in the Automotive Industry. Based upon ASTM D 4066, Classification System for Nylon Injection and Extrusion Materials (PA), it calls for additional descriptive characteristics and properties commonly used in the Automotive Industry. This document applies to natural and non-color matched black, heat-stabilized polyamide compounds only. Color matched compounds shall be defined by the proprietary OEM standards. This document allows for the use of recycled, reconstituted, and regrind materials provided that the requirements as stated in this document are met, the material has not been altered or modified to change its suitability for safe processing and use, and the material shall be identified as such.
This SAE Recommended Practice is applicable to all heat exchangers used in vehicle and industrial cooling systems. This document outlines the tests to determine the heat transfer and pressure drop performance of heat exchangers under specified conditions. This document has been reviewed and revised by adding several clarifying statements to Section 4.
This recommended practice provides a guideline for qualifying automotive aftermarket, two-component structural foams, and defines a classification system for such foams.
This specification covers an aluminum alloy in the form of castings.
This specification covers a copper-beryllium alloy in the form of bars, rods, shapes, and forgings (see 8.5).
This procedure covers vehicle operation and electric dynamometer (dyno) load coefficient adjustment to simulate track road load within dynamometer inertia and road load simulation capabilities.
This SAE Aerospace Recommended Practice (ARP) provides recommendations for design and test requirements for a generic “passive” side stick that could be used for fly-by wire transport and business aircraft. It addresses the following: The functions to be implemented The geometric and mechanical characteristics The mechanical and electrical interfaces The safety and certification requirements
This specification covers a corrosion- and heat-resistant iron-nickel-chromium alloy in the form of bars and forgings 4.0 inches (102 mm) and under and forging stock of any size.
This SAE Aerospace Standard (AS) defines minimum performance standards, qualification requirements, and minimum documentation requirements for passenger and crew seats in civil rotorcraft, transport aircraft, and general aviation aircraft. The goal is to achieve comfort, durability, and occupant protection under normal operational loads and to define test and evaluation criteria to demonstrate occupant protection when a seat/occupant/restraint system is subjected to statically applied ultimate loads and to dynamic impact test conditions set forth in Title 14, Code of Federal Regulations (14 CFR) parts 23, 25, 27, or 29 (as applicable to the seat type). Two formats of this standard (MS Excel and Adobe PDF) are available. The standards provided in both formats (MS Excel and Adobe PDF) contain the same text.
This specification covers the requirements for an inorganic black coating applied at ambient temperature to steel to touch up black oxide coating in areas where the black oxide has been removed. This coating is intended only to visually change the surface to a black color, not to meet the requirements of any black oxide specification.
This specification covers the requirements for an electroless nickel-thallium-boron or nickel-boron deposit on various substrates.
This specification covers an aluminum alloy in the form of sheet, clad on one side.
Items per page:
50
1 – 50 of 219180