Results
This AIR provides information about the specific requirements for missile hydraulic pumps and their associated power sources.
This specification covers an aluminum alloy in the form of hand forgings 8 inches (203 mm) and under in nominal thickness and of forging stock (see 8.6).
This document applies to the development of Plans for integrating and managing COTS assemblies in electronic equipment and Systems for the commercial, military, and space markets, as well as other ADHP markets that wish to use this document. For purposes of this document, COTS assemblies are viewed as electronic assemblies such as printed wiring assemblies, disk drives, servers, printers, laptop computers, etc. There are many ways to categorize COTS assemblies1, including the following spectrum: At one end of the spectrum are COTS assemblies whose design, internal parts2, materials, configuration control, traceability, reliability, and qualification methods are at least partially controlled, or influenced, by ADHP customers (either individually or collectively) or by industry standards. An example at this end of the spectrum is a VME circuit card assembly. At the other end of the spectrum are COTS assemblies whose design, internal parts, materials, configuration control, and
This specification covers a copper-beryllium alloy in the form of bars, rods, shapes, and forgings (see 8.5).
This specification covers an aluminum alloy in the form of sheet and plate with a thickness of 0.125 to 0.499 inch (3.20 to 12.67 mm), inclusive (see 8.5).
This SAE Recommended Practice was developed primarily for passenger car and truck applications but may be used in marine, industrial, and similar applications. It addresses nonmetallic caps and both metallic and nonmetallic filler necks.
This specification covers a premium aircraft-quality, low-alloy steel in the form of bars, forgings, mechanical tubing, and forging stock.
This specification covers an aluminum-lithium alloy in the form of extruded profiles with a maximum cross-sectional area of 19 square inches (123 cm2) and a maximum circle size of 11 inches (279 mm) from 0.040 to 0.499 inch (1.00 to 12.50 mm) in thickness (see 8.6).
To establish the acceptance criteria for discontinuities as revealed by magnetic particle or liquid penetrant examination of aircraft utility parts as in 1.2.
This SAE Recommended Practice provides a method for determining the Effective Projected Luminous Lens Area (EPLLA) of a lamp function using design analysis. This standard was created to clarify and address how to determine EPLLA with traditional and new technologies.
The following schematic diagrams reflect various methods of illustrating automotive transmission arrangements. These have been developed to facilitate a clear understanding of the functional interrelations of the gearing, clutches, hydrodynamic drive unit, and other transmission components. Two variations of transmission diagrams are used: in neutral (clutches not applied) and in gear. For illustrative purposes, some typical transmissions are shown.
This SAE Recommended Practice describes the testing procedures that may be used to evaluate the integrity of ground ambulance-based occupant seating and occupant restraint systems for workers and civilians transported in the patient compartment of an ambulance when exposed to a frontal or side impact. This recommended practice was based on ambulance patient compartment dynamics and is not applicable to other vehicle applications or seating positions. This recommended practice is structured to accommodate seating systems installed in multiple attitudes including, but not limited to, side-facing, rear-facing, and forward-facing. Its purpose is to provide ambulance seating manufacturers, ambulance occupant restraint manufacturers, ambulance builders, and end users with testing procedures and, where appropriate, acceptance criteria that, to a great extent, ensures the occupant seating and occupant restraint system meet similar performance criteria as FMVSS 208 requires for seat belted
This SAE Recommended Practice applies to all commercial, self-propelled, or towed motor vehicles which transport property or passengers in interstate commerce in which the gross vehicle weight rating or gross combination weight rating exceeds 4550 kg (10 000 lb).
Almost all light trucks now are being manufactured with at least a driver side air bag and all will have dual air bags by 1998. The driving forces behind this feature are occupant safety, federal regulations, and competition in the industry. Along with the booming popularity of pickups and SUVs, they are commonly accessorized with a wide variety of products. Many accessories for four-wheel drives in particular are mounted on the front of the vehicle. These products include grille/brush guards, winches, snow plows, replacement bumpers, bicycle carriers, etc. Concerns have arisen over the compatibility of these accessories with the vehicle’s air bag system. The vehicle manufacturers are concerned because of their huge investment in design and crash test verification of the complete vehicle system and keen awareness of the federal regulations. The crushability of the front bumper and supporting structure are key elements in the system, so alterations to that area become logical concerns
This SAE Recommended Practice establishes uniform test procedures and certain minimum performance requirements for motor vehicle seats and seat adjusters. It is limited to tests that can be conducted on uniform test fixtures and equipment available in commercial laboratory test facilities. This practice includes a minimum requirement for horizontal forward loads encountered in vehicle forward impacts, and horizontal loads obtained by impacting the vehicle from the rear. The requirements and test procedures in this recommended practice reflect current technology and industry experience. It is intended to subject this recommended practice to a continuing review and revision as technology advances and experience is expanded.
This SAE Recommended Practice provides a system for classification and specification for limited number of polyamides (nylons) used in the Automotive Industry. Based upon ASTM D 4066, Classification System for Nylon Injection and Extrusion Materials (PA), it calls for additional descriptive characteristics and properties commonly used in the Automotive Industry. This document applies to natural and non-color matched black, heat-stabilized polyamide compounds only. Color matched compounds shall be defined by the proprietary OEM standards. This document allows for the use of recycled, reconstituted, and regrind materials provided that the requirements as stated in this document are met, the material has not been altered or modified to change its suitability for safe processing and use, and the material shall be identified as such.
In order to compare test results obtained from different crash test facilities, standardized coordinate systems need to be defined for crash test dummies, vehicle structures, and laboratory fixtures. In addition, recorded polarities for various transducer outputs need to be defined relative to positive directions of the appropriate coordinate systems. This SAE Information Report describes the standardized sign convention and recorded output polarities for various transducers used in crash testing.
This SAE Recommended Practice provides common data output formats and definitions for a variety of data elements that may be useful for analyzing the performance of automated driving system (ADS) during an event that meets the trigger threshold criteria specified in this document. The document is intended to govern data element definitions, to provide a minimum data element set, and to specify a common ADS data logger record format as applicable for motor vehicle applications. Automated driving systems (ADSs) perform the complete dynamic driving task (DDT) while engaged. In the absence of a human “driver,” the ADS itself could be the only witness of a collision event. As such, a definition of the ADS data recording is necessary in order to standardize information available to the accident reconstructionist. For this purpose, the data elements defined herein supplement the SAE J1698-1 defined EDR in order to facilitate the determination of the background and events leading up to a
This SAE Recommended Practice describes the dynamic testing procedures required to evaluate the integrity of patient compartment interior Storage Compartments such as cabinets, drawers, or refillable supply pouch systems when exposed to a frontal, side or rear impact (i.e., a crash impact). Its purpose is to provide component manufacturers, ambulance builders, and end-users with testing procedures and, where appropriate, acceptance criteria that, to a great extent, ensure interior Storage Compartments or systems meet the same performance criteria across the industry. Descriptions of the test set-up, test instrumentation, photographic/video coverage, test fixture, and performance metrics are included.
The scope of this document is to provide the design specifications/requirements/guidelines for concrete divider surrogates that represent actual concrete dividers to the in-vehicle sensors and can be used for performance assessment of such in-vehicle sensing systems in real-world test scenarios/conditions. Therefore, this document only includes the recommended concrete divider surrogate characteristics for automotive cameras, LiDARs, and/or radars. Concrete dividers are also known as concrete barriers [1].
This SAE Recommended Practice is intended to establish uniform procedures for developing specifications for automotive thermoplastics. It is intended for use by automotive companies and their suppliers of molded and/ or fabricated parts from thermoplastic materials.
This SAE standard covers the minimum mechanical properties measured on separately cast test pieces of varying thickness and microstructural requirements for ductile iron castings used in automotive and allied industries. Castings may be specified in the as-cast or heat-treated condition. If castings are heat-treated, prior approval from the customer is required. The appendix provides general information on chemical composition, microstructure and casting mechanical properties, as well as other information for particular service conditions. In this standard SI units are primary and in-lb units are derived.
This SAE Standard covers the minimum requirements for metric sizes of nonmetallic tubing as manufactured for use in air brake systems. Nonreinforced products are designated type A and reinforced products type B. It is not intended to cover tubing for any portion of the system that operates below -40 °C (-40 °F), above +93 °C (+200 °F), above a maximum working gage pressure of 1.0 MPa (150 psi), or in an area subject to attack by battery acid. This tubing is intended for use in the brake system for connections that maintain a basically fixed relationship between components during vehicle operation. Coiled tube assemblies required for those installations where flexing occurs are covered by this standard and SAE J1131 to the extent of setting minimum requirements on the essentially straight tube and tube fitting connections, which are used in the construction of such assemblies.2 NOTE—As all elements of SAE J1394 are being merged into SAE J844, two separate documents are no longer
This SAE Standard was developed to provide a method for indicating the direction of engine rotation and numbering of engine cylinders. The document is intended for use in designing new engines to eliminate the differences which presently exist in industry.
This SAE Recommended Practice describes test methods for measuring and identifying the natural frequencies for the lower order modes of an inflated radial tire with a fixed spindle while expending modest effort and employing a minimum of test equipment. The methods apply to any size of radial tire so long as the test equipment is properly scaled to conduct the measurements for the intended test tire. Two types of boundary conditions are considered for the tire: unloaded and loaded against a flat surface. The test involves the performance and measurement of an input vibratory force (excitation) to the tire and the corresponding vibratory output (response). The data are suitable for use in determining parameters for road load models and for comparative evaluations of the measured properties in research and development. NOTE 1—The focus of this standard is identification and reporting of the lower order natural frequencies of the tire using a simple test procedure. While higher order
This SAE Recommended Practice describes the test procedures for conducting quasi-static modular body strength tests for ambulance applications. Its purpose is to establish recommended test practices which standardize the procedure for Type I and Type III bodies, provide ambulance builders and end-users with testing procedures and, where appropriate, provide acceptance criteria that, to a great extent, ensures the ambulance structure meets the same performance criteria across the industry. Descriptions of the test set-up, test instrumentation, photographic/video coverage, and the test fixtures are included.
The purpose of this SAE Recommended Practice is to offer simplified and prioritized guidelines for collecting and preserving on-scene data related to motor vehicle crashes. It is intended that these guidelines improve the effectiveness of data collection, which will assist subsequent analysis and reconstruction of a particular crash. This document is intended to guide early data collectors whose objectives include documenting information related to the crash. It may be used by law enforcement personnel, safety officials, insurance adjusters and other interested parties. This document identifies categories of scene physical features that deteriorate relatively quickly and recommends documentation task priorities. Detailed methods of collecting data are not part of this document. However, some widely used methods are described in the references in Section 2.
This SAE Aerospace Standard provides minimum design, installation, and removal requirements for AS3319 through AS3322 studs and is applicable when specified on engineering drawings, or in procurement documents.
This engineering design specification provides parameters and general requirements for auxiliary front lamps to be used on motorcycles.
This SAE Information Report documents the problems with the 2002 regulated version of the spine box and defines a recommended solution to resolve the problem.
Items per page:
50
1 – 50 of 216105