Results
This AIR provides information about the specific requirements for missile hydraulic pumps and their associated power sources.
This specification covers an aluminum alloy in the form of welding wire.
This document is written to address acceleration and deceleration control issues related to heavy-duty trucks and buses greater than 10000 GVW.
This specification covers a leaded bronze in the form of sand and centrifugal castings (see 8.6).
This specification covers an aluminum alloy in the form of rolled or cold-finished bars, rods, and wire and of flash-welded rings and stock for flash-welded rings.
This SAE Standard covers a single Un-Jacketed (UTP) and Jacketed (J-UTP) Balanced Unshielded Twisted Pair data cable intended for use in surface vehicle cables for 10 Mb/s Ethernet shared bus applications. The tests in this document are intended to qualify cables for normal operation in an automotive environment while maintaining the necessary electrical properties for reliable data transmission.
This SAE Aerospace Standard (AS) establishes the requirements for a V-band grooved clamp couplings that are intended for use on fluid-line tubing joints, tailpipe joints, and accessory mount joints, on flight vehicles or other attachments. The semi-rigid coupling joint assemblies, hereafter referred to as “the joint”, shall operate within the temperature ranges specified in their applicable part standards.
This specification covers an aluminum alloy in the form of sand, investment, permanent mold, and composite mold castings with nominal wall thicknesses of up to 1.0 inch (25.4 mm), inclusive (see 8.8).
This specification covers a copper-zinc alloy (brass) in the form of laminated sheet with nominal thickness 0.006 to 0.125 inch (0.15 to 3.18 mm) (see 8.5).
This specification covers a premium aircraft-quality, corrosion-resistant steel in the form of sheet, strip, and plate.
This specification covers a 100% homopolymer of polychlorotrifluoroethylene (PCTFE) in the form of molded sheet 0.250 inch (6.35 mm) and under in nominal thickness.
This specification covers steel cleanliness requirements for premium aircraft-quality ferromagnetic steels, including hardenable, corrosion-resistant steels, by magnetic particle inspection methods. This specification contains sampling, sample preparation, inspection procedures, and cleanliness rating criteria (see 8.2).
This SAE Aerospace Standard (AS) defines the requirements for a polytetrafluoroethylene (PTFE) lined, metallic reinforced, hose assembly suitable for use in high pressure, 4000 psi, pneumatic systems for aircraft and missile ground servicing applications at temperatures of -65 to 160 °F.
This specification covers a corrosion- and heat-resistant steel in the form of bars, wire, forgings, mechanical tubing, flash-welded rings, and stock for forging or flash-welded rings.
The intent of this specification is for the procurement of the material listed on the QPL; therefore, no qualification or equivalency threshold values are provided. Users that intend to conduct a new material qualification or equivalency program must refer to the Quality Assurance section of the base specification, AMS6891.
This document provides a summary of names commonly used throughout the industry for aircraft fuel system components. It is a thesaurus intended to aid those not familiar with the lexicon of the industry.
Turbine engines installed in helicopters require a highly sophisticated oil system to fulfill two primary tasks: Cooling/oil supply Lubrication of rotating components (bearings, shafts, gears, etc.) While lubrication is an engine internal operation, depending on the engine oil system configuration, cooling and oil supply may require more or less design activity on the aircraft side of the engine/airframe interface for proper engine function. The necessity for engine cooling and oil supply provisions on the airframe can lead to interface problems because the helicopter manufacturer can influence engine related functions due to the design of corresponding oil system components.
This specification covers a corrosion-resistant steel in the form of investment castings.
This SAE Recommended Practice specifies the design and/or evaluation with the specific equipment, conditions, and methods for distributorless battery ignition systems intended for use in various internal combustion engines including automotive, marine, motorcycle, and utility engine applications. The test procedures listed in this document are limited to measurements performed on a test bench only and do not include measurements made directly on engines or vehicles. This standard is not intended to supply information for battery ignition systems used in aircraft applications of any type.
This specification covers two types of refined hydrocarbon compounds in the form of liquids. This specification only covers newly manufactured materials.
This document defines capabilities and limitations of FTIR spectroscopy as it pertains to counterfeit electronic component detection and suggests possible applications to these ends. Additionally, this document outlines requirements associated with the application of FTIR spectroscopy including: operator training, sample preparation, various sampling techniques, data interpretation, computerized spectral matching including pass/fail criteria, equipment maintenance, and reporting of data. The discussion is primarily aimed at analyses performed in the mid-infrared (IR) from 400 to 4000 wavenumbers; however, many of the concepts are applicable to the near and far IR. If AS6171/9 is invoked in the contract, the base document, AS6171 General Requirements shall also apply.
This specification covers an aluminum alloy in the form of wire, sheet, foil, pig, grains, shot, and chips (see 8.6).
This specification covers an aluminum alloy in the form of die forgings, hand forgings, and rolled rings 4 inches (102 mm) and under in nominal thickness and forging stock of any size (see 8.6).
Items per page:
50
1 – 50 of 215954