Results
This SAE Information Report SAE J2836/6 establishes use cases for communication between plug-in electric vehicles and the EVSE for wireless energy transfer as specified in SAE J2954. It addresses the requirements for communications between the on-board charging system and the wireless EV supply equipment (WEVSE) in support of detection of the WEVSE, the charging process, and monitoring of the charging process. Since the communication to the charging infrastructure and the power grid for smart charging will also be communicated by the WEVSE to the EV over the wireless interface, these requirements are also covered. However, the processes and procedures are expected to be identical to those specified for V2G communications specified in SAE J2836/1. Where relevant, the specification notes interactions that may be required between the vehicle and vehicle operator, but does not formally specify them. Similarly, communications between the on-board charging sub-system and the on-board vehicle
This specification covers a blend of chromium carbide and a nickel-chromium alloy in the form of powder.
This document provides recommendations involving BEV battery data retention and battery design that enhance the potential for BEV battery reuse and serviceability and that can improve recyclability. These recommendations have been developed by a group of professionals skilled in the secondary-use of batteries and in the research, development, and manufacture of BEV batteries and battery systems.
This document covers insulated, flexible air duct assemblies for portable ground support air conditioners and heaters.
This SAE Aerospace Standard (AS) provides a method for gas turbine engine performance computer programs to be written using Fortran COMMON blocks. If a “function-call application program interface” (API) is to be used, then ARP4868 and ARP5571 are recommended as alternatives to that described in this document. When it is agreed between the program user and supplier that a particular program shall be supplied in Fortran, this document shall be used in conjunction with AS681 for steady-state and transient programs. This document also describes how to take advantage of the Fortran CHARACTER storage to extend the information interface between the calling program and the engine subroutine.
The automotive air-conditioning service ports task force conducted a field survey with MACS (Mobile Air Climate Systems Association) in June 2021. The scope of this survey was to determine the types of failures reported primarily at member service shops related to automotive air-conditioning service ports.
This SAE Aerospace Recommended Practice (ARP) contains the general requirements and test procedures for Dual Mode (NVIS Friendly visible and Covert) exterior lighting for most rotorcraft and fixed wing aircraft and could be applicable to ground vehicles that desire a Dual Mode lighting system.
This SAE Aerospace Recommended Practice (ARP) defines minimum requirements for an aircraft transport ULD to transport horses properly and safely by air, to protect the horse(s) from injuries, and to protect the aircraft from corrosion created by waste spill. The ULD is designed to accommodate one horse or several. There are two types of ULDs for aircraft transportation of horses:
This SAE Aerospace Standard (AS) sets forth criteria for the selection and verification processes to be followed in providing tires that will be suitable for intended use on civil aircraft. This document encompasses new and requalified radial and bias aircraft tires.
This SAE Aerospace Standard (AS) specifies the dimensions, tolerances and size codes (dash numbers) for O-rings with a larger cross-section than those to AS568, for use in glands per MIL-G-5514 where squeeze at low temperature is often insufficient to provide a leak-tight seal.
This SAE Aerospace Standard (AS) covers variable speed, reversible battery powered drills with removable, rechargeable battery pack and either 3/8 inch or ½ inch chuck used for general maintenance and construction where a battery powered tool is required. This document also satisfies EMI requirements for driver drills, where EMI suppression is required by the purchaser. This document may involve hazardous materials, operations, or equipment and does not purport to address all of the safety considerations associated. It is the responsibility of the user of a piece of equipment to establish appropriate safety and health practices and to determine the applicability of regulatory limitations prior to its use. Users are cautioned to read all manufacturer’s instructions prior to use.
This test method outlines the recommended machine function, fixtures, and procedures used to test airframe rolling element bearings for dynamic performance under steady unidirectional radial load and oscillatory motion. Bearings covered by this test method shall be ball, roller, or needle type in either annular or rod end configuration, used in airframe control applications.
This SAE Recommended Practice is intended to serve as a reference for the amount of torque that a Power Take-Off can induce on the transmission mounting pad. This document will apply to six-bolt, eight-bolt, and rear mounted power take-offs.
This specification defines the requirements for a grooved clamp coupling and flanges suitable for joining intermediate pressure and temperature ducting in aircraft air systems. The rigid coupling joint assembly, hereafter referred to as "the joint", shall operate within the temperature range of -65 °F to +800 °F.
Items per page:
50
1 – 50 of 219717