Results
The primary objective of this recommended practice is to confirm that vehicles can communicate a minimum set of information in accordance with diagnostic test services specified in SAE J1979-2, or the equivalent ISO 14229-1:2013 (Ed. 2) and SAE J1979-3 documents. A successful result using the SAE J1699-5 Automotive Alliance for Innovation (AAI) software for OBD-II testing indicates that the main aspects of UDS communication have been examined, but it does not provide assurance of complete compliance with all aspects of SAE J1979-2 or SAE J1979-3. SAE J1699-5 tests run with a SAE J2534 device hardware and API that is not fully compliant will result in a test failure. This specification takes precedence over all conflicts in the documents cited in this section.
This SAE Information Report provides SAE’s recommendations for meeting the requirements for Real Emissions Assessment Logging (REAL) oxides of nitrogen (NOx) accuracy demonstration and for the implementation of REAL NOx binning requirements as defined in onboard diagnostics (OBD) regulations 13 CCR 1971.1 and 13 CCR 1968.2.
This specification covers a corrosion- and heat-resistant nickel alloy in the form of plate nominally 2.00 inches (50.8 mm) and under in thickness, inclusive.
This SAE Information Report establishes a uniform procedure for assuring the manufactured quality, installed utility, and performance of automotive remote steering controls other than those provided by the vehicle manufacturer (OEM). These products are intended to provide driving capability to persons with physical disabilities. The adaptive modifications seek to compensate for lost or reduced function in the extremities of the driver with a disability. Remote steering controls are designed to provide a steering input device alternative to the OEM steering wheel that either reduces the required input force, changes the required range of motion or changes the location of the steering control, or any combination of the above. These controls supplement by power, other than by the driver’s own muscular efforts, the force output of the driver with a disability. Because this is an Information Report, the numerical values for performance measurements presented in this report and in the
This SAE Aerospace Information Report (AIR) describes procedures for use in the field to determine if 115/200 Volt, 400 Hz aircraft external electrical power connectors are excessively worn, which may result in the inability of the external power plug to be retained, intermittent electrical performance, and arcing.
This specification covers pure gold in the form of wire 0.005 to 0.040 inch (0.012 to 1.000 mm), inclusive, in nominal diameter and ribbon 0.002 to 0.051 inch (0.05 to 1.28 mm), inclusive, in nominal thickness (see 8.5).
This specification covers a corrosion- and heat-resistant cobalt alloy in the form of bars, forgings, flash-welded rings, and stock for forging or flash-welded rings.
This specification covers a corrosion- and heat-resistant nickel alloy in the form of seamless tubing.
This specification covers a corrosion-resistant steel in the form of investment castings.
This SAE Recommended Practice was developed primarily for gasoline-powered passenger car and truck applications to interface vapor recovery systems, but it may be used in diesel, marine, industrial, and similar applications where a nozzle is required for filling. The zones cover nozzle spout access and handle clearance to a refilling port. In addition, this recommended practice includes a design window for nozzle manufacturers to develop with.
This specification covers a corrosion-resistant steel in the form of sheet, strip, and plate.
This specification, in conjunction with the general requirements for steel heat treatment covered in AMS2759, establishes the requirements for heat treatment of precipitation-hardening corrosion-resistant, maraging, and secondary hardening steel parts. Parts are defined in AMS2759. Parts made from steels other than those specified in this specification may be heat treated in accordance with the applicable requirements herein using processing temperatures, times, and other parameters recommended by the material producer unless otherwise specified by the cognizant engineering organization. General ordering instructions are specified in AMS2759.
This specification covers a corrosion- and heat-resistant nickel alloy in the form of sheet, strip, and plate.
The purpose of this SAE Aerospace Recommended Practice (ARP) is to provide the sample selection and endurance time test procedures for SAE Type II, III, and IV aircraft deicing/anti-icing fluids, required for the generation of endurance time data of acceptable quality for review by the SAE G-12 Holdover Time Committee. The related standard ARP5718 provides the process by which endurance time data is converted to holdover times for publication by regulators and subsequent use by aircraft operators.
This SAE Aerospace Information Report (AIR) covers the general requirements for, and the listing of, manufacturers’ identification markings, names, symbols or trademarks, and CAGE codes that appear on electrical and electronic wiring devices and accessories as required by individual product specifications. Supplier markings from previous submitted listings are maintained for component traceability.
This specification covers a corrosion- and heat-resistant steel in the form of bars, forgings, and forging stock.
This specification covers the requirements for thermal spray coatings applied using the high velocity oxygen fuel (HVOF) combustion process. This specification is not intended to be used for duplex coatings, i.e., the application of the coating over a previously applied coating.
This procedure measures the resistance to radiant heat flow of insulating materials in sleeve, tubing, or tape (collectively referred to as “sleeve”) form. The sleeve’s effectiveness (SE) is determined by measuring the difference in surface temperature of a flat black, single-diameter ceramic cylinder with and without the standard diameter sleeve at the specified temperature, position, and distance from the radiant heat source.
This specification covers procedures and requirements for peening of metal parts with portable, bonded-shot, rotary flap assemblies in accordance with AS2592. The principles of rotary flap peening are similar to conventional shot peening, except conversion of arc height values using the magnetic test Almen strip holder is required for intensity determination.
This document is intended to establish a procedure to certify AD fallback test driver skill levels as an endorsement to SAE J3300 foundational level certification. The SAE J3300/3 endorsement can be used by the individual driver to qualify their skills as a test driver of vehicles with automated driving features. The SAE J3300/3 endorsement levels may also be used by test facilities or other organizations when seeking test or professional drivers with these skills. This document provides directions for obtaining the endorsement, including associated AD fallback test driving skill examination requirements, through SAE J3300-certified Examiners (refer to SAE J3300 for definition). Endorsement registration and associated records are administered through Probitas Authentication®. Probitas Authentication® is the current Independent Program Administrator for the SAE J3300 series. This document is a supplement to SAE J3300, providing information specific to the AD fallback test driver skill
Primarily to provide recommendations concerning minimizing stress-corrosion cracking in wrought titanium alloy products.
This specification covers a two-component compound, an epoxy resin base and a hardener, in the form of a paste.
This SAE Standard was developed to provide a method for indicating the direction of engine rotation and numbering of engine cylinders. The document is intended for use in designing new engines to eliminate the differences which presently exist in industry.
This analysis applies to crane types as covered by ASME B30.5.
This SAE Aerospace Standard (AS) covers ULDs utilized in finding submerged aircraft. Such ULDs are installed within the aircraft in a manner that they are unlikely to become separated during crash conditions. The low frequency ULD should be attached to the airframe in accordance with the manufacturer’s recommendations in order to maximize the underwater detection range. ARINC Standard 677 also provides installation guidance for Low Frequency ULDs.
This Information Report presents background and rationale for SAE Recommended Practice J1106, Laboratory Testing Machine and Procedures for Measuring the Steady Force and Moment Properties of Passenger Car Tires. The purpose of SAE J1106 is to define standards for equipment design and test procedures so that data from different laboratories can be directly compared. Whereas such standardization is not a requirement for testing associated with tire development, it is necessary in the context of vehicle design and tire selection problems. The basic approach employed in developing SAE J1106 was to consolidate and document existing technology as embodied in equipment and procedures currently employed for routine tire evaluations. Equipment and procedures whose current use is restricted to research applications were not considered. Research experience is discussed in this Information Report, however, to the extent deemed necessary to provide background and rationale for SAE J1106. Material
This Purchasing Specification (PS), AMS3970/3, specifies the batch release and delivery requirements for carbon fiber fabric epoxy prepreg used for repair. This specification is applicable only when the carbon fiber fabric epoxy prepreg is used as part of the repair system defined in AMS3970 and AMS3970/1. This specification also defines the procedure and requirements for storage life extension of materials purchased against this specification. It is only applicable for materials that are qualified against AMS3970 (refer to PRI QPL AMS3970) and shall be carried out within the responsibility of the purchaser and under control of its Quality organization.
This document provides guidance concerning the maintenance and serviceability of oxygen cylinders beginning with the quality of oxygen that is required, supplemental oxygen information, handling and cleaning procedures, transfilling, and marking of serviced oxygen assemblies. This document attempts to outline in a logical sequence oxygen quality, serviceability, and maintenance of oxygen cylinders. Content of this document can also be used for refilling oxygen cylinders while installed on aircraft, directly or through an intermediate charging port.
This specification covers a corrosion and heat-resistant steel in the form of sheet, strip, and plate.
This specification covers non-silicone synthetic rubber sealing compounds supplied as a two-component or pre-mixed and frozen (PMF) system that cures at room temperature.
Items per page:
50
1 – 50 of 222736