Results
This SAE Aerospace Standard (AS) provides requirements for design and installation of aircraft jacking pad adapters and the mating jack socket interface to permit use of standard jacking equipment to be used in civil and military transport aircraft. The adapter defined herein shall be the key interface between the aircraft and the aircraft jack(s).
This SAE Recommended Practice is intended to establish a procedure to certify the fundamental driving skill levels of professional drivers. This certification can be used by the individual driver to qualify their skills when seeking employment or other professional activity. These certification levels may also be used by test facilities or other organizations when seeking test or professional drivers of various skills. The associated family of documents listed below establish driving skill criteria for various specific categories. SAE J3300: Driving level SAE J3300/1: Low mu/winter driving SAE J3300/2: Trailer towing SAE J3300/3: Automated driving Additional certifications to be added as appropriate. This main document provides: (1) common definitions and general guidance for using this family of documents, (2) directions for obtaining certification through Probitas Authentication®1, and (3) driving level examination requirements.
In the analysis and measurement of residual stresses of materials, it has been noted that there are frequently differences in interpretation of the terms "macrostrain" and "microstrain." To assist communication among research personnel in this area, definitions for these two terms are suggested by the Fatigue Design and Evaluation Committee of SAE. Since "macrostress" is commonly computed from "macrostrain" in residual stress analysis, to be consistent, the definitions given are for "macrostrain" and "microstrain."
This SAE Standard covers the engineering requirements for peening surfaces of parts by impingement of metallic shot, glass beads, or ceramic shot.
This SAE Standard defines the method for deriving and verifying the peening intensity exerted onto a part surface during shot peening or other surface enhancement processes.
This SAE Surface Vehicle Recommended Practice deals with electrostatic charge phenomena that may occur in automotive fuel systems and applies to the following: Fuels that are in a liquid state at ambient temperatures and atmospheric pressures and are contained in vehicle fuel tanks that operate at or near atmospheric pressure. This includes gasoline and diesel fuels, as well as their blends with additives such as alcohols, esters, and ethers, whether the additives are petroleum based or bio-fuel based. The group of components that comprise the fuel system (in contact and not in contact with fuels). Other components in proximity to the fuel system that may be affected by electrostatic fields caused by the fuel system. Electrostatic phenomena that arise from, or are affected by, the following aspects of vehicle or fuel system operation: ○ Flowing fuel in the fuel delivery system. ○ Flowing fuel being dispensed to the vehicle while it is being fueled.
AS22759 specification covers fluoropolymer-insulated single conductor electrical wires made with tin-coated, silver-coated, or nickel-coated conductors of copper or copper alloy as specified in the applicable detail specification. The fluoropolymer insulation may be polytetrafluoroethylene (PTFE), fluorinated ethylene propylene (FEP), polyvinylidene fluoride (PVF2), ethylene-tetrafluoroethylene copolymer (ETFE), or other Fluoropolymer resin. The fluoropolymer may be used alone or in combination with other insulation materials. These abbreviations shall be used herein. When a wire is referenced herein, it means an insulated conductor (see 7.7).
To define a test procedure that will provide repeatable measurements of a vehicle’s maximum acceleration performance for launch and passing maneuvers and standardize time zero used in reported results.
This SAE Standard presents the minimum requirements for nonmetallic tubing with one or more layers manufactured for use as liquid-carrying or vapor-carrying component in fuel systems for gasoline, or alcohol blends with gasoline. Requirements in this document also apply to monowall tubing (one layer construction). When the construction has one or more layers of polymer-based compounds in the wall, the multilayer constructions are primarily for the purpose of improvement in permeation resistance to hydrocarbons found in various fuels. The tube construction can have a straight-wall configuration, a wall that is convoluted or corrugated, or a combination of each. It may have an innermost layer with improved electrical conductivity for use where such a characteristic is desired. The improved electrical conductivity can apply to the entire wall construction, if the tubing is a monowall. (For elastomeric based MLT constructions, refer to SAE J30 and SAE J2405). Unless otherwise agreed to by
This SAE Standard was developed to provide a method for indicating the direction of engine rotation and numbering of engine cylinders. The document is intended for use in designing new engines to eliminate the differences which presently exist in industry.
This SAE Recommended Practice outlines labeling guidelines and performance requirements for printed information and warning labels used on components, subsystems, and systems. It covers content, placement, and durability requirements throughout the product life cycle, from initial production to recycling or disposal.
This SAE Recommended Practice is intended as a guide toward standard practice and is subject to change to keep pace with experience and technical advances. This document provides standardized laboratory tests, test methods and equipment, and requirements for lighting devices covered by SAE Recommended Practices and Standards. It is intended for devices used on vehicles less than 2032 mm in width. Tests for vehicles larger than 2032 mm in overall width are covered in SAE J2139. Device-specific tests and requirements can be found in applicable SAE Technical Reports.
This document describes [motor] vehicle driving automation systems that perform part or all of the dynamic driving task (DDT) on a sustained basis. It provides a taxonomy with detailed definitions for six levels of driving automation, ranging from no driving automation (Level 0) to full driving automation (Level 5), in the context of [motor] vehicles (hereafter also referred to as “vehicle” or “vehicles”) and their operation on roadways: Level 0: No Driving Automation Level 1: Driver Assistance Level 2: Partial Driving Automation Level 3: Conditional Driving Automation Level 4: High Driving Automation Level 5: Full Driving Automation These level definitions, along with additional supporting terms and definitions provided herein, can be used to describe the full range of driving automation features equipped on [motor] vehicles in a functionally consistent and coherent manner. “On-road” refers to publicly accessible roadways (including parking areas and private campuses that permit
This document is written to address acceleration and deceleration control issues related to heavy-duty trucks and buses greater than 10000 GVW.
This SAE Aerospace Standard (AS) contains requirements for a digital time division command/response multiplex data bus, for use in systems integration that is functionally similar to MIL-STD-1553B with Notice 2 but with a star topology and some deleted functionality. Even with the use of this document, differences may exist between multiplex data buses in different system applications due to particular application requirements and the options allowed in this document. The system designer must recognize this fact and design the multiplex bus controller (BC) hardware and software to accommodate such differences. These designer selected options must exist to allow the necessary flexibility in the design of specific multiplex systems in order to provide for the control mechanism, architectural redundancy, degradation concept, and traffic patterns peculiar to the specific application requirements.
This document provides guidance in performing Failure/Fault Analyses in relatively low complexity systems. Methodologies and processes are presented and described for accomplishing Failure/Fault Analyses. ARP4761 provides updated methods and processes for use on civil aircraft safety assessment. When analyzing these types of systems, ARP4761 should be used in lieu of this ARP.
This recommended practice defines methods for the measurement of periodic, random and transient whole-body vibration. It indicates the principal factors that combine to determine the degree to which a vibration exposure will cause discomfort. Informative appendices indicate the current state of knowledge and provide guidance on the possible effects of motion and vibration on discomfort. The frequency range considered is 0.5 Hz to 80 Hz. This recommended practice also defines the principles of preferred methods of mounting transducers for determining human exposure. This recommended practice is applicable to light passenger vehicles (e.g., passenger cars and light trucks). This recommended practice is applicable to motions transmitted to the human body as a whole through the buttocks, back and feet of a seated occupant, as well as through the hands of a driver. This recommended practice offers a method for developing a ride performance index but does not specifically describe how to
ARP1834 provides general guidance for the selection, approach to, and performance of various kinds of F/FA of digital systems and equipment. Its prime objective is to present several industry-acceptable, cost-effective methods for identifying, analyzing, and documenting digital-equipment failure modes and their effects. The analysis techniques and considerations presented here are directed to digital-equipment hardware faults and failures exclusively. ARP1834 is not intended as an exhaustive treatment of the enormously complex process involved in the analytical failure evaluation of complete digital systems, nor as a universally applicable, definitive listing of the necessary and sufficient steps and actions for such evaluation. ARP4761 provides updated methods and processes for use on civil aircraft safety assessment. When analyzing these types of systems, ARP4761 should be used in lieu of this ARP. ARP1834 addresses the following areas of consideration in the preparation and
This SAE Recommended Practice describes the chemical composition, and physical characteristic requirements for high-carbon cast-steel grit, to be used for blast cleaning and etching operations.
This SAE Recommended Practice describes chemical composition and physical characteristic requirements for high-carbon cast-steel shot to be used for shot peening or blast cleaning operations.
This SAE Recommended Practice defines requirements for equipment and supplies to be used in measuring shot peening arc height and other surface enhancement processes. It is intended as a guide toward standard practice and is subject to change to keep pace with experience and technical advances. Guidelines for use of these items can be found in SAE J443 and SAE J2597.
This SAE Recommended Practice defines a procedure for the use of computer generated saturation curves to determine peening intensity. Calculation of intensity within a tolerance band for each data set in Table 1 one is required for compliance with this practice.
"Effective particle or domain size" is a phrase used in X-ray diffraction literature to describe the size of the coherent regions within a material which are diffracting. Coherency in this sense means diffracting as a unit. Small particle size causes X-ray line broadening and as such can be measured. It has been shown related to substructure as observed in transmission electron microscopy. Particle size is affected by hardening, cold working, and fatigue; conversely, there is increasing evidence that particle size, per se, affects both static and dynamic strength.
This specification covers characteristics for chemistry, microstructure, density, hardness, size, shape, and appearance of zirconium oxide-based ceramic shot, suitable for peening surfaces of parts by impingement.
This SAE Recommended Practice pertains to blast cleaning and shot peening and provides for standard cast shot and grit size numbers. For shot, this number corresponds with the opening of the nominal test sieve, in ten thousandths of inches1, preceded by an S. For grit, this number corresponds with the sieve designation of the nominal test sieve with the prefix G added. These sieves are in accordance with ASTM E11. The accompanying shot and grit classifications and size designations were formulated by representatives of shot and grit suppliers, equipment manufacturers, and automotive users.
This SAE Recommended Practice is intended as a guide toward standard practice and is subject to change to keep pace with experience and technical advances. This document establishes performance requirements, design requirements, and design guidelines for electronic devices.
This specification covers a premium aircraft-quality alloy steel in the form of welding wire.
This SAE Information Report is intended to provide users and producers of metallic shot and grit2 with general information on methods of mechanically testing metal shot in the laboratory.
The purpose of this document is to present general considerations for the design and use of aircraft wheel chocks. The design and use of aircraft wheel chocks is a good deal more complicated than it may appear at first glance.
This SAE Aerospace Recommended Practice (ARP) is intended as a guide toward standard practice and is subject to change to keep pace with experience and technical advances.
This SAE Aerospace Standard (AS) covers the requirements for polytetrafluoroethylene (PTFE) hose assemblies for use in aerospace fuel and lubricating oil systems at temperatures between -67 and 450 °F and at operating pressures per Table 1. The hose assemblies are also suitable for use within the same temperature and pressure limitations in aerospace pneumatic systems, where some gaseous diffusion through the wall of the PTFE liner can be tolerated. Standard hose assembly configurations are defined in AS7051 through AS7056. The use of these hose assemblies in pneumatic storage systems is not recommended. In addition, installations in which the limits specified herein are exceeded, or in which the application is not covered specifically by this document, for example oxygen, shall be subject to the approval of the purchaser.
This document is a supplement to SAE/USCAR 17 and is intended to give recommended usages for one and two-way RF connectors and dimensional requirements for 2-way RF connectors and hybrid (RF & DC power) connectors which are not currently specified elsewhere. The radio frequency (RF) connector interface specified herein is suited for unsealed and sealed automobile applications up to 6 GHz and is intended for in-line, board mount, device mount, straight or angled applications. Dimensional requirements are specified in this document to ensure interchangeability. Compliance with the dimensional requirements of this specification will not guarantee interoperability between different suppliers mating connectors. It is the supplier responsibility to ensure RF performance requirements are met with other suppliers mating connectors. Performance requirements are specified in SAE/USCAR-2, and in SAE/USCAR-17.
This radio frequency (RF) connector interface specification is suited for unsealed automobile applications up to 2 GHz. Dimensional requirements are specified in this document to ensure interchangeability. This RF connector interface specification is intended for in-line, board mount, device mount, straight or angled applications. Performance requirements are specified in SAE/USCAR-2, and in SAE/USCAR-17.
This SAE Standard is concerned with the geometrical irregularities of surfaces of solid materials. It established definite classifications for various degrees of roughness and waviness and for several varieties of lay. It also provides a set of symbols for use on drawings and in specifications, reports, and the like. The ranges for roughness and waviness are divided into a number of steps, and the general types of lay are established by type characteristics. This standard does not define what degrees of surface roughness and waviness or what type of lay are suitable for any specific purpose. It does not specify the means by which any degree of such irregularities may be obtained or produced. Neither is it concerned with the other surface qualities such as luster, appearance, color, corrosion resistance, wear resistance, hardness, microstructure, and absorption characteristics, any of which may be governing considerations in specific applications. Sufaces, in general, are very complex
SAE J448, Surface Texture, has been set up for precision reference specimens using a controlled surface profile to obtain reproducible roughness values. These specimens are for instrument calibration. Appropriate symbols for roughness, waviness, and lay have also been standardized (ASA B46.1-1962 and SAE J448). For production control, especially from one geographical location to another, means are required to facilitate the inspection of surface characteristics called for by specifications which include not only roughness but profile waviness and lay. In order to integrate the requirements of the designer with the actual production of surfaces, a second grade of control standards must be adopted which will be functional in nature for the specific product being manufactured. These control standards may be Calibrated Pilot Specimens (actual parts with satisfactory texture) or Roughness Comparison Specimens (ASA B46.1-1962). This SAE Recommended Practice describes the usage of these
Items per page:
50
1 – 50 of 211724