Results
This supplement forms a part of SAE Aerospace Specification AS85421. It shall be used to identify fitting standards citing this procurement specification.
This SAE Standard establishes the test procedure, environment, and instrumentation for determining the sound levels of snowmobiles in the stationary test mode. This test method is intended to provide an accurate measurement of exhaust and other engine noise and may be used to evaluate new and in-use snowmobiles to determine compliance with noise control regulations. Sound level measurements obtained with this test method are not intended as an engineering determination of overall machine noise. For this purpose, the use of SAE J192 is recommended.
This specification covers a premium aircraft-quality, high-alloy steel gas-atomized and HIP-consolidated in the form of bars, wire, forgings, and forging stock.
This standard defines a generic set of electrical interfaces between a host aircraft (“platform”) and an electro-optic/infrared (EO/IR) sensor. This includes connectors, cabling, fiber optics, signals, and power.
This standard describes a requirement for automotive tire traceability. It includes a definition of the RFID tag and the associated tire data set that can be accessed using the RFID tag as an identifier. The standard describes a unique identification and the associated data set for each tire produced by the tire fabricator. This data will either be provided or transmitted at the time of shipment to retailers, wholesalers or original equipment vehicle manufacturers. Tire identification code and data may be used for error proofing, determining the tire specifications or supporting any inquiries that occur for the duration of its automotive life.
This specification presents requirements for thin-walled (inside diameter greater than four times the wall thickness and outside diameter 1/4 inch and larger) corrosion-resistant steel tubing in approximately the 1/8 hard condition, of special quality, suitable for use in high-pressure hydraulic systems.
This specification covers a premium aircraft-quality, low-alloy steel in the form of bars, forgings, mechanical tubing, and forging stock.
This method covers electric outboards that are rated in terms of static thrust.
This SAE Recommended Practice provides test performance requirements for air disc brake actuators for service and combination service parking brake actuators with respect to function, durability, and environmental performance when tested according to SAE J2902.
The scope of this SAE Information Report is to provide general information relative to the nature and use of infrared techniques for nondestructive testing. The document is not intended to provide detailed technical information, but will serve as an introduction to the theory and capabilities of infrared testing and as a guide to more extensive references.
(These definitions were prepared by the Joint Committee on Definitions of Terms Relating to Heat Treatment appointed by the American Society for Testing and Materials, The American Society for Metals, the American Foundrymen's Association, and the SAE.) This SAE revision emphasizes the terms used in heat treating ferrous alloys, but also includes for reference some non-ferrous definitions at the end of the document. This glossary is not intended to be a specification, and it should not be interpreted as such. Since this is intended to be strictly a set of definitions, temperatures have been omitted purposely.
This specification covers a premium aircraft-quality steel in the form of bars, forgings, mechanical tubing, flash welded rings up through 10.000 inches (254.00 mm) inclusive in diameter or least distance between parallel sides, and stock of any size for forging or flash welded rings.
This document sets forth design and operational recommendations concerning the human factors issues and criteria for airborne terrain separation assurance systems. The visual and aural characteristics are covered for both the alerting components and terrain depiction/situation components. The display system may contain any one or a combination of these components. Although the system functionality assumed for this document exemplifies commercial aircraft implementation, the recommendations do not exclude other fixed wing aircraft types. Because of their unique operations with respect to terrain, rotorcraft will be addressed in a separate document. The assumptions about the system that guided and bounded the recommendations included: the system will have a human centered design based on the "lessons learned" from past systems; the system is not intended to replace the Ground Proximity Warning System (GPWS) function; the system is an on-board system that is not dependent on ground
When identifying the content of this report, one of the goals was that it supports a nationally interoperable method for connected vehicles (CVs) to make traffic signal priority and/or preemption (TSPP) requests of connected intersections (CIs) that support priority and/or preemption services. Given that, this report specifies the over-the-air (OTA) interface between CVs and CIs to support TSPP applications using updated revisions of the SAE J2735 Signal Request Message (SRM) and Signal Status Message (SSM) and the use of a Wireless Access in Vehicular Environments (WAVE) Service Advertisement (WSA) to advertise support for TSPP at a CI. Included are a concept of operations, requirements, design, and message structure definitions developed using a detailed systems engineering process.
The Class A Task Force of the Vehicle Network for Multiplexing and Data Communications Subcommittee is providing information on sensors that could be applicable for a Class A Bus application. Sensors are generally defined as any device that inputs information onto the bus. Sensors can be an input controlled by the operator or an input that provides the feedback or status of a monitored vehicle function. Although there is a list of sensors provided, this list is not all-inclusive. This SAE Information Report is intended to help the network system engineer and is meant to stimulate the design thought process.
This material type has resistance to hot air, but generally has poor resistance to fuels and lubricants, but usage is not limited to such applications. Each application should be considered separately. This material type has a typical service temperature range of -85 to 500 °F (-65 to 260 °C). The operating temperature range of the material is a general temperature range, but the presence of particular fluids and design parameters may modify this range. Recommendations on the material selection are based on available technical data and are offered as suggestions only. Each user should make his own tests to determine the suitability for his own particular use.
This SAE Surface Vehicle Information Report identifies and defines the assembly/disassembly and certification procedures relating to the use of the Hybrid III Large Male Test Dummy.
This specification covers a magnesium alloy in the form of sand castings.
This SAE Standard covers the mechanical and material requirements for three grades of steel nuts suitable for use in automotive and related engineering applications, in sizes 1/4 to 1-1/2 inches, inclusive, and with dimensions conforming with the requirements of the latest issue of SAE J482 or ASME B18.2.2, except for machine screw nuts which are not covered in this standard. This document does not include limits for surface discontinuities. Where usage requires such control, limits may be specified separately. For sizes 1/4 through 1 inch, this may be done by the statement: “Surface discontinuities shall not exceed the limits specified in ASTM F812/F812M.”
This SAE Recommended Practice establishes a method of evaluating the structural integrity of the entire brake system of all passenger cars under extreme braking conditions.
Items per page:
50
1 – 50 of 220494