Results
This test method provides a procedure for measuring no-load rotational breakaway torque of self-lubricating spherical bearings.
This SAE Information Report establishes a uniform procedure for assuring the manufactured quality, installed utility, and performance of automotive remote steering controls other than those provided by the vehicle manufacturer (OEM). These products are intended to provide driving capability to persons with physical disabilities. The adaptive modifications seek to compensate for lost or reduced function in the extremities of the driver with a disability. Remote steering controls are designed to provide a steering input device alternative to the OEM steering wheel that either reduces the required input force, changes the required range of motion or changes the location of the steering control, or any combination of the above. These controls supplement by power, other than by the driver’s own muscular efforts, the force output of the driver with a disability. Because this is an Information Report, the numerical values for performance measurements presented in this report and in the
This SAE Aerospace Information Report (AIR) describes procedures for use in the field to determine if 115/200 Volt, 400 Hz aircraft external electrical power connectors are excessively worn, which may result in the inability of the external power plug to be retained, intermittent electrical performance, and arcing.
The primary objective of this recommended practice is to confirm that vehicles can communicate a minimum set of information in accordance with diagnostic test services specified in SAE J1979-2, or the equivalent ISO 14229-1:2013 (Ed. 2) and SAE J1979-3 documents. A successful result using the SAE J1699-5 Automotive Alliance for Innovation (AAI) software for OBD-II testing indicates that the main aspects of UDS communication have been examined, but it does not provide assurance of complete compliance with all aspects of SAE J1979-2 or SAE J1979-3. SAE J1699-5 tests run with a SAE J2534 device hardware and API that is not fully compliant will result in a test failure. This specification takes precedence over all conflicts in the documents cited in this section.
This SAE Information Report provides SAE’s recommendations for meeting the requirements for Real Emissions Assessment Logging (REAL) oxides of nitrogen (NOx) accuracy demonstration and for the implementation of REAL NOx binning requirements as defined in onboard diagnostics (OBD) regulations 13 CCR 1971.1 and 13 CCR 1968.2.
This specification covers a corrosion- and heat-resistant nickel alloy in the form of plate nominally 2.00 inches (50.8 mm) and under in thickness, inclusive.
This specification covers a corrosion- and heat-resistant cobalt alloy in the form of bars, forgings, flash-welded rings, and stock for forging or flash-welded rings.
This specification covers pure gold in the form of wire 0.005 to 0.040 inch (0.012 to 1.000 mm), inclusive, in nominal diameter and ribbon 0.002 to 0.051 inch (0.05 to 1.28 mm), inclusive, in nominal thickness (see 8.5).
This specification covers a palladium-silver alloy in the form of round wire 0.004 to 0.080 inch (0.10 to 2.03 mm), inclusive, in nominal diameter (see 8.5).
The following schematic diagrams reflect various methods of illustrating automotive transmission arrangements. These have been developed to facilitate a clear understanding of the functional interrelations of the gearing, clutches, hydrodynamic drive unit, and other transmission components. Two variations of transmission diagrams are used: in neutral (clutches not applied) and in gear. For illustrative purposes, some typical transmissions are shown.
This document covers the mechanisms from the power cylinder, which contribute to the mechanical friction of an internal combustion engine. It will not discuss in detail the influence of other engine components or engine driven accessories on friction.
This specification covers the specific requirements for 7178 aluminum alloy plate and sheet material; the general requirements are covered in AMS-QQ-A-250.
The scope of this document is to aid in the selection of hose and hose assembly titles.
This specification covers requirements for material used in electrical insulating heat shrinkable components. The continuous operating temperature of these materials shall range from -75°C to +200°C (-103°F to +392°F). (See 6.1).
Scope is unavailable.
The intent of this document is to define the methodology for suspect parts inspection using radiological inspection. The purpose of radiology for suspect counterfeit part inspection is to detect deliberate misrepresentation of a part, either at the part distributor or original equipment manufacturer (OEM) level. Radiological inspection can also potentially detect unintentional damage to the part resulting from improper removal of part from assemblies, which may include, but not limited to, prolonged elevated temperature exposure during desoldering operations or mechanical stresses during removal. Radiological inspection of electronics includes film radiography and filmless radiography such as digital radiography (DR), real time radiography (RTR), and computed tomography (CT). Radiology is an important tool used in part verification of microelectronic devices. Radiographic analysis is performed on parts to verify that the internal package or die construction is consistent with an
Consideration for the damaging effects to aircraft from the failure of wheels and tires should be evaluated. This document discusses the types of problems in-service aircraft have experienced and methodology in place to assist the designers when evaluating threats for new aircraft design. The purpose of this document is to provide a history of in-service problems, provide a historical summary of the design improvements made to wheels and tires during the past 40 years, and to offer methodology which has been used to help designers assess the threat to ensure the functionality of systems and equipment located in and around the landing gear and in wheel wells.
This SAE Standard provides a means for specifying or describing the pertinent properties of fiberboards for automotive applications. The materials normally specified by this standard are defined in SAE J947. The test methods commonly used for fiberboards are defined in SAE J315.
To define a list of anomalies related to OBD Communications. Misinterpretations of various OBD Communications Standards and Recommended Practices have resulted in OBD “no-communications” situations in the field. This Information Report identifies the most prevalent of these.
This document describes: a The preparatory steps to test experimental Type I fluids according to AMS1424; b The recommendations for the preparation of samples for endurance time testing according to ARP5945; c A short description of the recommended field spray test; d The protocol to demonstrate that Type I fluid can be used with the Type I holdover time guidelines published by the FAA and Transport Canada, including endurance time data obtained from ARP5945; e The protocol for inclusion of Type I fluids on the FAA and Transport Canada lists of fluids; f The protocol for updating the FAA and Transport Canada lists of fluids; g The role of the SAE G-12 Aircraft Deicing Fluids Committee; h The role of the SAE G-12 Holdover Time Committee; and i The process for the publication of Type I holdover time guidelines. This document does not describe laboratory-testing procedures. This document does not include the qualification requirements for AMS1428 Type II, III, and IV fluids (these are
This document sets forth general, functional, procedural, and design criteria and recommendations concerning human engineering of data link systems. The recommendations are based on limited evidence from empirical and analytic studies of simulated data link communication, and on experience from operational tests and actual use of data link. However, because data are not yet available to support recommendations on all potentially critical human engineering issues these recommendations necessarily go beyond the data link research and include requirements based on related research and human factors engineering practice. It is also recognized that evolution of these recommendations will be appropriate as experience with data link accumulates and new applications are implemented. This document focuses primarily on recommendations for data link communications between an air traffic specialist and a pilot, i.e., air traffic services communications, although some recommendations address use of
This document establishes common industry practices and recommended screening, qualification, and lot acceptance testing of Plastic Encapsulated Microcircuits (PEMs) for use in space application environments.
SAE J1939-31 network layer describes the requirements and services for network interconnection ECUs (NIECU) that enable electronic control units (ECUs) on an SAE J1939 network segment to intercommunicate with other ECUs on different network segments of the vehicle or system network. This document defines various types of NIECUs. The information in this document applies only to ECUs that are intended to provide networking services. It is not necessary for an ECU to provide any of these services in order to be compliant with the SAE J1939 protocol.
This document establishes training guidelines applicable to fiber optic fabricator technical training for individuals involved in the manufacturing, installation, support, integration and testing of fiber optic systems. Applicable personnel include: Managers Engineers Technicians Trainers/Instructors Third Party Maintenance Agencies Quality Assurance Production
This specification covers a chloroprene (CR) rubber sponge in the form of sheet, strip, molded shapes, or other forms, as ordered.
This specification covers a premium aircraft-quality, low-alloy steel in the form of bars, forgings, mechanical tubing, and forging stock.
This specification covers an aluminum alloy in the form of castings (see 8.6).
This specification covers a low-alloy steel in the form of bars, forgings, mechanical tubing, and forging stock.
This document establishes the requirements for screw-on type reattachable couplings for use in low temperature hose assemblies.
This SAE Recommended Practice establishes minimum performance requirements for trucks, buses, truck-tractors, full trailers, and semitrailers with gross vehicle weight ratings greater than 4540 kg (10 000 lb) with regard to: a Vehicle classification b Vehicle load c Percent grade d Application force
This SAE Aerospace Standard (AS) provides a method for gas turbine engine performance computer programs to be written using Fortran COMMON blocks. If a “function-call application program interface” (API) is to be used, then ARP4868 and ARP5571 are recommended as alternatives to that described in this document. When it is agreed between the program user and supplier that a particular program shall be supplied in Fortran, this document shall be used in conjunction with AS681 for steady-state and transient programs. This document also describes how to take advantage of the Fortran CHARACTER storage to extend the information interface between the calling program and the engine subroutine.
Items per page:
50
1 – 50 of 222741