Results
This supplement forms a part of SAE Aerospace Specification AS85421. It shall be used to identify fitting standards citing this procurement specification.
This SAE Standard establishes the test procedure, environment, and instrumentation for determining the sound levels of snowmobiles in the stationary test mode. This test method is intended to provide an accurate measurement of exhaust and other engine noise and may be used to evaluate new and in-use snowmobiles to determine compliance with noise control regulations. Sound level measurements obtained with this test method are not intended as an engineering determination of overall machine noise. For this purpose, the use of SAE J192 is recommended.
This SAE Recommended Practice specifies the design and/or evaluation with the specific equipment, conditions, and methods for distributorless battery ignition systems intended for use in various internal combustion engines including automotive, marine, motorcycle, and utility engine applications. The test procedures listed in this document are limited to measurements performed on a test bench only and do not include measurements made directly on engines or vehicles. This standard is not intended to supply information for battery ignition systems used in aircraft applications of any type.
These general guidelines and precautions apply to personnel operating directional drilling tracking equipment when used with horizontal directional drilling (HDD) machines as defined in ISO 21467:2023.
This specification covers a low-alloy steel in the form of welding wire. Type 2 - copper coated wire was removed from this document (see 8.4).
This specification covers a high strength, corrosion and heat-resistant cobalt-nickel-chromium alloy in the form of bars (see 8.4).
This SAE Standard provides a table of textual messages meeting the requirements for expressing “Radio Data Systems” (RDS) phrases commonly used in the ITS industry. They can be used both over the RDS subcarrier transmission media as part of a 37-bit long “Group 8a message” as well as being used to provide a common content list of phrases used in a wide number of other media and applications. This document SHALL define the normative index values to be used, extending the CEN established list to provide phrases needed by US practitioners. This standard provides non-normative textual phrases which MAY be used by implementers to ensure intelligible results. This document SHALL follow the formats and rules established in SAE J2540 in the expressions, manipulations, and use of such tables. It should be pointed out that within the rules established by this document a variety of final table are all considered “compliant” with the document, and may vary as fits the needs of implementers.
This ARP defines a recommended placard for readily identifying equipment with aircraft phosphate ester fluid to be used in the aircraft hydraulic systems to assure compatibility between the internal seals/materials and the system fluid. A definition is provided for a durable type and semipermanently attached placard with prescribed text for the permissible fluid are included in the document.
This document establishes general design criteria, tolerances, and limits of application for tooling, fixtures, and accessories for mounting and driving gas turbine engine rotors on horizontal and vertical balancing machines.
This specification covers a polytetrafluoroethylene (PTFE) resin filled with 10% mineral and 2.5% molybdenum disulfide in the form of extruded or molded rods or tubes which are sintered after molding or, in the case of extrusions, sintered during the extrusion process.
SCOPE IS UNAVAILABLE
This document covers metric studs made from a corrosion and heat resistant, age hardenable iron base alloy of the type identified under the Unified Numbering System as UNS S66286. The following specification designations and their properties are covered:
This SAE Aerospace Standard (AS) specifies the dimensions, tolerances and size codes (dash numbers) for O-rings with a larger cross-section than those to AS568, for use in glands per MIL-G-5514 where squeeze at low temperature is often insufficient to provide a leak-tight seal.
This specification covers a low-carbon steel in the form of seamless tubing up to 5.50 inches (139.7 mm), nominal OD, inclusive.
This document applies to laser proponents involved with the use of laser systems outdoors. It may be used in conjunction with AS4970, ARP5535, ARP5572, and the ANSI Z136 series of laser safety standards.
This specification covers the requirements for one type of tiedown fitting for installation in the floors of aircraft.
This SAE Aerospace Standard (AS) covers any protective system that serves the stated purpose.
This specification covers a corrosion and heat-resistant alloy in the form of sheet, strip, and plate 2.00 inch (50.8 mm) and under in thickness (see 8.4).
This specification covers a fluorocarbon (FKM) rubber in the form of O-rings, compression seals, O-ring cord, and molded-in-place gaskets for aeronautical and aerospace applications. For sheet, strip, tubing, extrusions, and molded shapes use the AMS3353 specification which is intended for that use.
SCOPE IS UNAVAILABLE.
This SAE Information Report provides a list of those SAE steels which, because of decreased usage, have been deleted from the standard SAE Handbook listings. Included are alloy steels from SAE J778 deleted since 1936, carbon steels from SAE J118 deleted since 1952, and all EX-steels deleted from SAE J1081. Information concerning SAE steels prior to these dates may be obtained from the SAE office on request. With the issuance of this report, SAE J778, Formerly Standard SAE Alloy Steels, and SAE J118, Formerly Standard SAE Carbon Steels, will be retired since they are now combined in SAE J1249. In the future, new assignments to SAE J1081, Chemical Compositions of SAE Experimental Steels, will be given “PS” (Potential Standard) numbers rather than “EX” numbers. The steels listed in Tables 1 and 2 are no longer considered as standard steels. Producers should be contacted concerning availability. Steel grades can be reinstated based on usage according to the critieria indicated in SAE J403
This SAE Part Standard covers selected inch dimensioned tapping screws and metallic drive screws manufactured in accordance with American Society for Mechanical Engineers dimensional standards. This SAE standard covers material most often used in ship systems and equipment but its use may be applied wherever fasteners of the covered materials are used. This standard permits the fasteners to be identified and ordered by a Part Identification Number (PIN) as defined in this standard.
This SAE Surface Vehicle Recommended Practice deals with electrostatic charge phenomena that may occur in automotive fuel systems and applies to the following: Fuels that are in a liquid state at ambient temperatures and atmospheric pressures and are contained in vehicle fuel tanks that operate at or near atmospheric pressure. This includes gasoline and diesel fuels, as well as their blends with additives such as alcohols, esters, and ethers, whether the additives are petroleum based or bio-fuel based. The group of components that comprise the fuel system (in contact and not in contact with fuels). Other components in proximity to the fuel system that may be affected by electrostatic fields caused by the fuel system. Electrostatic phenomena that arise from, or are affected by, the following aspects of vehicle or fuel system operation: Flowing fuel in the fuel delivery system. Flowing fuel being dispensed to the vehicle while it is being fueled.
This specification covers an aluminum alloy in the form of welding wire.
Items per page:
50
1 – 50 of 220494