Results
This AIR provides information about the specific requirements for missile hydraulic pumps and their associated power sources.
This specification covers a corrosion- and heat-resistant nickel alloy in the form of sheet, strip, and plate.
This specification covers a corrosion-resistant steel in the form of investment castings.
This SAE Recommended Practice establishes uniform procedures for testing BEVs that are capable of being operated on public and private roads. The procedure applies only to vehicles using batteries as their sole source of power. It is the intent of this document to provide standard tests that will allow for the determination of energy consumption and range for light-duty vehicles (LDVs) based on the federal test procedure (FTP) using the urban dynamometer driving cycle (UDDS) and the highway fuel economy driving schedule (HFEDS) and provide a flexible testing methodology that is capable of accommodating additional test cycles as needed. Additionally, this SAE Recommended Practice provides five-cycle testing guidelines for vehicles performing supplementary testing on the US06, SC03, and cold FTP procedures. Realistic alternatives should be allowed for new technology. Evaluations are based on the total vehicle system’s performance and not on subsystems apart from the vehicle.
This specification covers a corrosion- and heat-resistant steel in the form of sheet, strip, and plate.
This specification covers a corrosion- and heat-resistant nickel alloy in the form of bars, forgings, flash-welded rings, and stock for forging, flash-welded rings, or heading.
This specification covers a free-machining, corrosion-resistant steel in the form of bars, wire, forgings, and forging stock.
Three levels of fan structural analysis are included in this practice: a Initial structural integrity. b In-vehicle testing. c Durability (laboratory) test methods. The initial structural integrity section describes analytical and test methods used to predict potential resonance and, therefore, possible fatigue accumulation. The in-vehicle (or machine) section enumerates the general procedure used to conduct a fan strain gage test. Various considerations that may affect the outcome of strain gage data have been described for the user of this procedure to adapt/discard depending on the particular application. The durability test methods section describes the detailed test procedures for a laboratory environment that may be used depending on type of fan, equipment availability, and end objective. The second and third levels build upon information derived from the previous level. Engineering judgment is required as to the applicability of each level to a different vehicle environment or a
This SAE Recommended Practice is intended to cover plastic safety glazing for use in motor vehicles and motor vehicle equipment. Nominal specifications for thickness, flatness, curvature, size, and fabrication details are presented principally for the guidance of body engineers and designers. For additional information on plastic safety glazing materials for use in motor vehicles and motor vehicle equipment, please refer to SAE J673.
The scope of this SAE Recommended Practice is to promote compatibility between child restraint systems and vehicle seats and seat belts. Design guidelines are provided to vehicle manufacturers for certain characteristics of seats and seat belts and to child restraint system (CRS) manufacturers for corresponding CRS features so that each can be made more compatible with the other. The CRS accommodation fixture (see Figure 1) is used to represent a CRS to the designers of both the vehicle interior and the CRS for evaluation of each product for compatibility with the other. The features of the accommodation fixture are described as each is used.
This specification covers a titanium alloy in the form of bars, wire, forgings, flash-welded rings 4.000 inches (101.60 mm) and under in diameter or least distance between parallel sides, and stock of any size for forging or flash-welded rings (see 8.6).
The following schematic diagrams reflect various methods of illustrating automotive transmission arrangements. These have been developed to facilitate a clear understanding of the functional interrelations of the gearing, clutches, hydrodynamic drive unit, and other transmission components. Two variations of transmission diagrams are used: in neutral (clutches not applied) and in gear. For illustrative purposes, some typical transmissions are shown.
This specification covers columbium in the form of sheet, strip, plate, and foil.
This SAE Information Report introduces key concepts and properties of adhesives, sealants, and heat transfer materials (HTMs) and the roles they serve in present-day battery systems applications. The basic chemistry and properties of the three types of materials are summarized along with important health and environmental information. Relevant material dispense methodologies and equipment for material dispensing is reviewed. A series of representative battery applications examples employing adhesives, sealants, and HTMs is also provided with particular attention given to end-use performance.
The SAE J2923 procedure is a recommended practice that applies to on-road vehicles with a GVWR below 4540 kg equipped with disc brakes.
This specification covers a copper-zinc alloy (brass) in the form of sheet, strip, and plate (see 8.6).
The purpose of this SAE Recommended Practice is to establish a uniform laboratory procedure for securing and reporting the friction and wear characteristics of brake linings. The performance data obtained can be used for in-plant quality control by brake lining manufacturers and for the quality assessment of incoming shipments by the purchasers of brake linings.
This SAE Recommended Practice defines requirements for equipment and supplies to be used in measuring shot peening intensity and other surface enhancement processes. It is intended as a guide toward standard practice and is subject to change to keep pace with experience and technical advances. Guidelines for use of these items can be found in SAE J443 and SAE J2597.
This specification covers an aluminum alloy in the form of sheet from 0.063 to 0.249 inch (1.60 to 6.30 mm) in nominal thickness (see 8.6).
This specification covers a low-alloy steel in the form of sheet, strip, and plate 4.00 inches (101.6 mm) and under in thickness.
This SAE Recommend Practice establishes for passenger cars, light trucks, and multipurpose vehicles with GVW of 4500 kg (10000 pounds) or less, as defined by the EPA, and M1 category vehicles, as defined by the European Commission:
This specification covers a corrosion and heat resistant steel in the form of sheet, strip, and plate.
This SAE Standard was developed to provide a method for indicating the direction of engine rotation and numbering of engine cylinders. The document is intended for use in designing new engines to eliminate the differences which presently exist in industry.
This specification covers a magnesium alloy in the form of investment castings (see 8.6).
This SAE Aerospace Recommended Practice (ARP) provides the user with standardized guidelines for the measurement of effective intensity of short pulse width strobe anticollision lights for aircraft in the laboratory, in maintenance facilities, and in the field. A common source of traceability for calibration of the measurement systems, compensation for known causes of variation in light output such as the use of colored lenses, and recommendations which minimize sources of errors and uncertainties are included in this document. Estimates of uncertainty and error sources for each class of measurement are discussed.
This specification covers a magnesium alloy in the form of investment castings (see 8.6).
This specification covers a nitriding grade of premium aircraft-quality, low-alloy steel in the form of bars, forgings, mechanical tubing, and forging stock. AMS6496 and AMS6497 cover UNS K23280 with other quality levels.
This specification covers an aluminum alloy in the form of rolled or forged rings up to 6 inches (152 mm), inclusive, in thickness (see 3.3.1.1.1) and an OD to wall thickness ratio of 10 or greater (see 8.5).
AMS6885/1 gives information about the technical requirements and qualification procedure for unidirectional carbon fiber tape epoxy repair prepreg capable of curing under vacuum for repair of carbon fiber reinforced epoxy structures. The repair system includes an epoxy film adhesive to be applied in a co-bonding process with the prepreg for solid laminate and sandwich bonding.
Items per page:
50
1 – 50 of 216102