Results
This SAE Information Report SAE J2836/6 establishes use cases for communication between plug-in electric vehicles and the EVSE for wireless energy transfer as specified in SAE J2954. It addresses the requirements for communications between the on-board charging system and the wireless EV supply equipment (WEVSE) in support of detection of the WEVSE, the charging process, and monitoring of the charging process. Since the communication to the charging infrastructure and the power grid for smart charging will also be communicated by the WEVSE to the EV over the wireless interface, these requirements are also covered. However, the processes and procedures are expected to be identical to those specified for V2G communications specified in SAE J2836/1. Where relevant, the specification notes interactions that may be required between the vehicle and vehicle operator, but does not formally specify them. Similarly, communications between the on-board charging sub-system and the on-board vehicle
This specification covers a blend of chromium carbide and a nickel-chromium alloy in the form of powder.
This document provides recommendations involving BEV battery data retention and battery design that enhance the potential for BEV battery reuse and serviceability and that can improve recyclability. These recommendations have been developed by a group of professionals skilled in the secondary-use of batteries and in the research, development, and manufacture of BEV batteries and battery systems.
This specification covers the requirements for heat-treatment of four classes of steel (See 1.2) and the requirements for furnace equipment, test procedures and information for heat-treating procedures, heat-treating temperatures and material (See 6.3) test procedures. This specification is applicable only to the heat treatment of raw material (See 6.3.1); it does not cover the requirements for the heat treatment of steel parts (See 3.4 and 6.3.2). This specification also describes procedures that, when followed, will produce the desired properties and material qualities within the limitations of the respective alloys tabulated in Tables 1A, 1B, 1C and 1D. Alloys other than those specifically covered herein may be heat treated using all applicable requirements of this specification.
This specification establishes general requirements for the processes listed in 3.8.1 for heat treatment of steel parts (see 8.2.1) by users or their vendors or subcontractors.
This specification covers a premium aircraft-quality, high-strength, low-alloy steel in the form of bars, forgings, mechanical tubing, flash welded rings, and stock for forging or flash welded rings.
This specification covers a premium aircraft quality, low-alloy steel in the form of bars, forgings, mechanical tubing, and forging stock.
This specification covers a premium aircraft-quality, low-alloy steel in the form of bars, forgings, mechanical tubing, and forging stock.
This specification covers a premium aircraft-quality alloy steel in the form of bars and forgings 199 square inches (1284 cm2) and under in cross section, and forging stock of any size.
This specification covers an aircraft-quality, low-alloy steel in the form of bars, forgings, mechanical tubing, and forging stock.
This specification covers a premium aircraft-quality, low-alloy steel in the form of bars, forgings, mechanical tubing, and forging stock.
This document establishes the requirements for the sequencing of processes relating to parts fabricated from 300M or 4340 modified steel heat treated to, or to be heat treated to, 270,000 psi (1860 MPa) minimum ultimate tensile strength (UTS) and higher.
This specification covers procedures for sampling and testing aircraft-quality, special aircraft-quality, and premium aircraft-quality steels requiring transverse tensile property testing.
This specification covers a maraging steel in the form of welding wire.
This specification, in conjunction with the general requirements for steel heat treatment covered in AMS2759, establishes the requirements for heat treatment of carbon and low-alloy steel parts to minimum ultimate tensile strengths below 220 ksi (1517 MPa). Parts are defined in AMS2759. Due to limited hardenability in these materials, there are size limits in this specification.
This specification covers established inch/pound manufacturing tolerances applicable to low-alloy steel sheet, strip, and plate ordered to inch/pound dimensions. These tolerances apply to all conditions unless otherwise noted. The term “excl” is used to apply only to the higher figure of the specified range.
This specification covers a low-carbon steel in the form of bars, forgings, mechanical tubing, and forging stock.
This specification covers a premium aircraft-quality, low-alloy steel in the form of bars, forgings, mechanical tubing, and forging stock.
This specification covers a carbon steel in the form of sheet and strip.
This specification covers a low-alloy steel in the form of welding wire.
This specification covers a low-alloy steel in the form of welding wire.
This specification covers a low-alloy steel in the form of bare welding wire. Type 2 - copper coated wire was removed from this document (see 8.4).
This specification covers an aircraft-quality, low-alloy steel in the form of mechanical tubing.
This specification, in conjunction with the general requirements for steel heat treatment in AMS2759, establishes requirements for thermal stress-relief treatments of parts manufactured from the following materials: a Carbon and low-alloy steels b Tool steels c Precipitation-hardening, corrosion-resistant, and maraging steels d Austenitic corrosion-resistant steels e Martensitic corrosion-resistant steels
This specification covers an aircraft-quality, low-alloy steel in the form of sheet, strip, and plate.
This specification covers a premium aircraft-quality, low-alloy steel in the form of bars, forgings, mechanical tubing, and forging stock.
This specification establishes requirements for steel forgings of any shape or form from which finished parts are to be made (See 8.2, 8.3, & 8.4). This specification covers steel forgings suitable for use in the construction of aircraft/aerospace equipment
This Purchasing Specification, AMS6885/4, specifies the batch release and delivery requirements for film adhesive used for repair. This specification is applicable only when the film adhesive is used as part of the repair system defined in AMS6885 and AMS6885/1. This specification also defines the procedure and requirements for storage life extension of materials purchased against this specification. It is only applicable for materials qualified against AMS6885 (refer to PRI-QPL-AMS6885), and shall be carried out within the responsibility of the purchaser and under control of its Quality organisation.
This specification covers a corrosion-resistant steel in the form of welding wire.
This Technical Specification gives information about technical requirements and qualification procedures of adhesive paste with or without thickening agent for core restoration of aircraft components.
This specification covers a premium aircraft-quality steel in the form of bars, forgings, mechanical tubing, flash welded rings up through 10.000 inches (254.00 mm) inclusive in diameter or least distance between parallel sides, and stock of any size for forging or flash welded rings.
This specification covers a premium aircraft-quality, low-alloy steel in the form of bars, forgings, mechanical tubing, and forging stock.
This specification covers a premium aircraft-quality, low-alloy steel in the form of bars, forgings, mechanical tubing, and forging stock.
This specification covers procedures for obtaining first-article (preproduction) approval of forgings and the controls to be exercised in producing subsequent production forgings.
This specification covers a carbon steel in the form of sheet, strip, and plate.
This specification covers an aircraft-quality, low-alloy, heat-resistant steel in the form of bars, forgings, mechanical tubing, and forging stock.
This specification covers a low-alloy steel in the form of bars, forgings, mechanical tubing, and forging stock.
This specification covers chrome-molybdenum (4130) steel bars and forging stock of aircraft quality.
This specification covers a carbon steel in the form of strip.
Items per page:
50
1 – 50 of 219717