Results
This AIR provides information about the specific requirements for missile hydraulic pumps and their associated power sources.
This SAE Aerospace Recommended Practice (ARP) establishes the overall component and system function guidelines and minimum performance levels for a TPMS. These guidelines include, but are not limited to: Design recommendations for system components, which: Monitor tire inflation Are located in/on the tire/wheel assembly, landing gear axle, and/or aircraft avionics compartment Recommended performance and safety guidelines for a TPMS.
This specification covers a corrosion-resistant steel in the form of wire.
This procurement specification covers bolts made from a corrosion-resistant, work-strengthened, cobalt-chromium-nickel alloy of the type identified under the Unified Numbering System as UNS R30159.
This specification covers a low-alloy steel in the form of investment castings.
This specification covers a low-carbon steel in the form of seamless tubing up to 5.50 inches (139.7 mm), nominal OD, inclusive.
This specification covers a corrosion-resistant steel in the form of sand or centrifugal castings.
This specification covers a low-alloy steel in the form of investment castings.
This specification covers a carbon steel in the form of bars, forgings, mechanical tubing, and stock for forging or heading.
This specification covers a corrosion-resistant steel in the form of investment castings.
This specification covers a corrosion-resistant steel in the form of sheet, strip, and plate over 0.005 inch (0.13 mm) in nominal thickness.
This specification covers an iron-nickel alloy in the form of strip.
This specification covers an iron-nickel alloy in the form of strip 0.020 to 0.250 inch (0.51 to 6.35 mm), inclusive, in thickness.
This SAE Aerospace Information Report (AIR) presents data on normally accepted changes in physical properties and contamination levels for MIL-PRF-5606, MIL-PRF-83282, and MIL-PRF-87257 hydraulic fluids used in hydraulic test stands. This information is of importance to all users of hydraulic test stands to assure the performance data obtained on these test stands for specific components will not be adversely affected by excessive changes in fluid properties or contamination levels.
This Aerospace Standard, (AS), specifies minimum performance standards for _____________ (Instrument or instrument systems) which are primarily intended for use with (vehicles capable of flight), ((fixed wing, rotary wing) aircraft)), (other special modifiers); (and whose purpose is to display _____________ information).
This specification covers a titanium alloy in the form of wire, forgings, flash-welded rings 4.000 inches (101.60 mm), inclusive, and under in nominal diameter or distance between parallel sides, bars up through 10.000 inches (254 mm), inclusive, and under in nominal diameter with a maximum cross-sectional area for bars over 4.000 to 10.000 inches (101.60 to 254 mm) in diameter of 79 square inches (509.7 cm2), and stock for forging or flash-welded rings of any size (see 8.6).
This specification covers an aluminum alloy in the form of castings.
This specification covers an aluminum alloy in the form of sheet, clad on one side.
This specification covers an aluminum alloy in the form of castings (see 8.6).
This procurement specification covers aircraft-quality solid rivets and tubular end rivets made from a carbon steel of the type identified under the Unified Numbering System as UNS G10100.
SAE J1978-1 specifies a complementary set of functions to be provided by an OBD-II scan tool. These functions provide complete, efficient, and safe access to all regulated OBD (on-board diagnostic) services on any vehicle which complies to SAE J1979. The content of this document is intended to satisfy the requirements of an OBD-II scan tool as required by current U.S. OBD regulations. This document specifies: A means of establishing communications between an OBD-equipped vehicle and an OBD-II scan tool. A set of diagnostic services to be provided by an OBD-II scan tool in order to exercise the services defined in SAE J1979. In addition, SAE J1978-1 covers first generation protocol functionality defined in SAE J1979 plus automatic protocol determination for all SAE J1979/J1979-2/J1979-3 application content. The presentation of the SAE J1978 document family, where SAE J1978-1 covers first generation protocol functionality defined in SAE J1979 and protocol determination for SAE J1979, SAE
This specification covers a corrosion and heat resistant steel in the form of forgings, wire, bars, and mechanical tubing, flash welded rings, and stock of any size for forging or flash welded rings.
This document defines a set of standard application layer1 interfaces called JAUS Core Services. JAUS Services provide the means for software entities in an unmanned system or system of unmanned systems to communicate and coordinate their activities. The Core Services represent the infrastructure commonly found across all domains and types of unmanned systems. At present, eight services are defined in this document: Transport Service: Abstracts the functionality of the underlying communication transport layer Events Service: Establishes a publish/subscribe mechanism for automatic messaging Access Control: Manages preemptable exclusive control for safety critical operations Management: Defines component life-cycle management Time: Allows clients to query and set the system time for the component Liveness: Provides a means to maintain connection liveness between communicating components Discovery: Governs automatic discovery of remote entities and their capabilities List Manager
This specification covers an aluminum alloy in the form of sheet, clad on two sides.
This document provides recommended practices for the design and selection of tube, hose, and fitting systems that are used to transmit hydraulic fluid on aircraft. NOTE: Guidance for the sizing of hydraulic tubing is contained in Appendix A.
This SAE Standard provides test procedures, requirements, and guidelines for turn signal lamps intended for use on vehicles of less than 2032 mm in overall width.
To provide specifications for lighting and marking of industrial wheeled equipment whenever such equipment is operated or traveling on a highway.
This specification covers a corrosion and heat resistant nickel alloy in the form of investment castings.
Items per page:
50
1 – 50 of 219516