Results
This supplement forms a part of SAE Aerospace Specification AS85421. It shall be used to identify fitting standards citing this procurement specification.
This SAE Standard establishes the test procedure, environment, and instrumentation for determining the sound levels of snowmobiles in the stationary test mode. This test method is intended to provide an accurate measurement of exhaust and other engine noise and may be used to evaluate new and in-use snowmobiles to determine compliance with noise control regulations. Sound level measurements obtained with this test method are not intended as an engineering determination of overall machine noise. For this purpose, the use of SAE J192 is recommended.
This SAE Aerospace Standard establishes the requirements for a V-retainer coupling, flanges, and seal suitable for joining high-pressure and high-temperature ducting in aircraft bleed air systems. The rigid coupling joint assembly, hereafter referred to as “the joint,” shall operate within the temperature range of -65 to +1200 °F.
This document defines the requirements for polytetrafluoroethylene (PTFE) lined, para-aramid reinforced, hose assemblies suitable for use in 275 °F (135 °C), 5080 psi (35000 kPa) aircraft hydraulic systems.
This SAE Recommended Practice establishes a uniform fluid specification for reference usage in specific documents, such as fluid power component test procedures, where a fluid designation is required.
This SAE Recommended Practice establishes a uniform fluid specification for reference usage in specific documents, such as fluid power component test procedures, where a fluid designation is required.
This standard covers all types of oxygen breathing equipment used in non-military aircraft. It is intended that this standard supplements the requirements of the detail specification or drawings of specific components or assemblies (e.g., regulators, masks, cylinders, etc.). Where a conflict exists between this standard and detail specifications, detail specifications shall take precedence.
This SAE Aerospace Recommended Practice (ARP) provides information and guidance for the control of hazardous laser exposure in the navigable airspace. This ARP does not address techniques that pilots can apply to mitigate laser illuminations during a critical phase of flight. Such mitigation strategies are described in ARP6378.
This standard describes the accepted methods used for preparing aerospace sealant test specimens for qualification and quality conformance or acceptance testing. AS5127/1 and AS5127/2 are to be used in conjunction with this document and the applicable AMS specifications.
AMS6885/2 gives specific information about the qualification program for unidirectional carbon fiber tape epoxy repair prepreg capable of curing under vacuum for repair of carbon fiber reinforced epoxy structures. The prepreg system shall include an epoxy film adhesive to be applied in a co-bonding process with the prepreg for solid laminate and sandwich bonding.
This standard includes ISO 9001:20152 quality management system requirements and specifies additional aviation, space, and defense industry requirements, definitions, and notes. It is emphasized that the requirements specified in this standard are complementary (not alternative) to customer and applicable statutory and regulatory requirements. If there is a conflict between the requirements of this standard and customer or applicable statutory or regulatory requirements, the latter shall take precedence. This International Standard specifies requirements for a quality management system when an organization: a needs to demonstrate its ability to consistently provide products and services that meet customer and applicable statutory and regulatory requirements, and b aims to enhance customer satisfaction through the effective application of the system, including processes for improvement of the system and the assurance of conformity to customer and applicable statutory and regulatory
This SAE Standard provides test procedures, performance requirements and guidelines for auxiliary high beam lamps.
This SAE Recommended Practice describes the recommended methods for testing flexible harness coverings for use on ground vehicle electrical distribution systems. It shall apply to all tapes, extruded tube, and textile tube.
This specification covers a titanium alloy in the form of welding wire (see 8.5).
The verification matrix (VM) in this slash sheet is intended for use to establish compliance to AS6174A. This slash sheet is applicable to AS6174A. Nothing in this slash sheet, however, supersedes applicable laws and regulations, unless a specific exemption has been obtained through judicial/legal channels.
This SAE Standard provides testing and functional requirements to meet specified minimum performance criteria for electronic probe-type leak detectors. The equipment specified here will identify smaller refrigerant leaks when servicing motor vehicle air conditioning systems, including those engineered with improved sealing and smaller refrigerant charges to address environmental concerns and increase system efficiency. This document does not address any safety issues concerning the equipment design or use beyond that of sampling a flammable refrigerant, save those described in 3.1 and 3.2 of this document. All requirements of this standard shall be verified in SAE J2911.
AMS6885/1 gives information about the technical requirements and qualification procedure for unidirectional carbon fiber tape epoxy repair prepreg capable of curing under vacuum for repair of carbon fiber reinforced epoxy structures. The repair system includes an epoxy film adhesive to be applied in a co-bonding process with the prepreg for solid laminate and sandwich bonding.
This FMEA standard describes potential failure mode and effects analysis in design (DFMEA), supplemental FMEA-MSR, and potential failure mode and effects analysis in manufacturing and assembly processes (PFMEA). It assists users in the identification and mitigation of risk by providing appropriate terms, requirements, rating charts, and worksheets. As a standard, this document contains requirements—”must”—and recommendations—”should”—to guide the user through the FMEA process. The FMEA process and documentation must comply with this standard as well as any corporate policy concerning this standard. Documented rationale and agreement with the customer are necessary for deviations in order to justify new work or changed methods during customer or third-party audit reviews.
This SAE Standard covers a single Un-Jacketed (UTP) and Jacketed (J-UTP) Balanced Unshielded Twisted Pair data cable intended for use in surface vehicle cables for 10 Mb/s Ethernet shared bus applications. The tests in this document are intended to qualify cables for normal operation in an automotive environment while maintaining the necessary electrical properties for reliable data transmission.
This specification covers columbium in the form of sheet, strip, plate, and foil.
This specification covers one grade of commercially pure titanium in the form of wire for welding filler metal (see 8.5).
This specification covers an aluminum alloy in the form of honeycomb core in a non-hexagonal, flexible cell configuration with the core being treated for increased corrosion resistance and furnished only in the expanded form (see 8.5).
This specification covers a titanium alloy in the form of bars, wire, forgings, and flash-welded rings up through 3.999 inches (101.57 mm), inclusive, and stock for forging, flash-welded rings, or heading (see 8.6).
This specification covers a titanium alloy in the form of wire for welding filler metal (see 8.5).
This Aerospace Standard establishes the preferred diameter-pitch combinations of ISO metric 60° screw threads recommended for use in the aerospace industry for metric module bolts and nuts.
Items per page:
50
1 – 50 of 220494