Results
This test method provides a procedure for measuring no-load rotational breakaway torque of self-lubricating spherical bearings.
This specification covers a corrosion- and heat-resistant nickel alloy in the form of plate nominally 2.00 inches (50.8 mm) and under in thickness, inclusive.
The primary objective of this recommended practice is to confirm that vehicles can communicate a minimum set of information in accordance with diagnostic test services specified in SAE J1979-2, or the equivalent ISO 14229-1:2013 (Ed. 2) and SAE J1979-3 documents. A successful result using the SAE J1699-5 Automotive Alliance for Innovation (AAI) software for OBD-II testing indicates that the main aspects of UDS communication have been examined, but it does not provide assurance of complete compliance with all aspects of SAE J1979-2 or SAE J1979-3. SAE J1699-5 tests run with a SAE J2534 device hardware and API that is not fully compliant will result in a test failure. This specification takes precedence over all conflicts in the documents cited in this section.
This SAE Information Report provides SAE’s recommendations for meeting the requirements for Real Emissions Assessment Logging (REAL) oxides of nitrogen (NOx) accuracy demonstration and for the implementation of REAL NOx binning requirements as defined in onboard diagnostics (OBD) regulations 13 CCR 1971.1 and 13 CCR 1968.2.
This SAE Aerospace Information Report (AIR) describes procedures for use in the field to determine if 115/200 Volt, 400 Hz aircraft external electrical power connectors are excessively worn, which may result in the inability of the external power plug to be retained, intermittent electrical performance, and arcing.
This SAE Information Report establishes a uniform procedure for assuring the manufactured quality, installed utility, and performance of automotive remote steering controls other than those provided by the vehicle manufacturer (OEM). These products are intended to provide driving capability to persons with physical disabilities. The adaptive modifications seek to compensate for lost or reduced function in the extremities of the driver with a disability. Remote steering controls are designed to provide a steering input device alternative to the OEM steering wheel that either reduces the required input force, changes the required range of motion or changes the location of the steering control, or any combination of the above. These controls supplement by power, other than by the driver’s own muscular efforts, the force output of the driver with a disability. Because this is an Information Report, the numerical values for performance measurements presented in this report and in the
This SAE Aerospace Recommended Practice (ARP) establishes a procedure for disposition of aircraft wheels that have been involved in accidents/incidents or have been exposed to overheat conditions or overload conditions from loss of adjacent tire pressure (paired wheels) or wheel tie bolts.
This SAE Aerospace Standard (AS) establishes the requirements for fluid fittings that combine both flanged fitting ends and beaded hose connections for use in all types of fluid systems.
This document defines the requirements for polytetrafluoroethylene (PTFE) lined, para-aramid reinforced, hose assemblies suitable for use in 275 °F (135 °C), 5080 psi (35000 kPa) aircraft hydraulic systems.
This specification prescribes the requirements for Titanium and Titanium-alloy castings produced by the investment casting process.
This method is intended to define the continuous upper temperature limit (CUTL) of thermoplastic elastomers and thermoset rubber with durometer hardness <=90 Shore A, to oxidation or other degradation when exposed solely to hot air for an extended period of time.
This specification covers a premium aircraft-quality, low-alloy steel in the form of bars, forgings, mechanical tubing, and forging stock.
This SAE Standard applies to new refrigerant used in motor vehicle passenger air-conditioning (A/C) systems designed to use HFC-134a. Hermetically sealed, refrigerated cargo systems are not covered by this document.
This specification covers a low-alloy steel in the form of welding wire.
The purpose of this SAE Information Report is to set up a guide as to body, frame, and wheel housing clearance to accommodate tire chains, and also the minimum bogie spacing to permit using chains on both axles. These dimensions apply to trucks, buses, and combinations of vehicles 10 001 lb (4535.06 kg) GVW and over, and are based upon recommendations of the Tire and Rim Association and of the National Association of Chain Manufacturers. The diagram shows clearance for chains over the tire ONLY and allowance must be made for spring deflections in determining fender clearance. See Figure 1 and Table 1.
This SAE Recommended Practice establishes a method of evaluating the structural integrity of the parking brake system of all new trucks, buses, and combination vehicles designed for roadway use in the following classifications: TRACTOR, TRAILER, TRUCK, AND BUS: over 4500 kg (10 000 lb) GVWR.
This SAE Standard covers the mechanical and physical requirements for Compacted Graphite Iron (CGI) castings used in automotive and allied industries. Requirements in this document include: a Tensile Strength b Yield Strength c Elongation d Graphite Morphology
This SAE Aerospace Standard (AS) covers requirements for nickel-chromium coatings, black oxide or black phosphate coatings, and alternative coatings for aerospace hand tools.
This FMEA standard describes potential failure mode and effects analysis in design (DFMEA), supplemental FMEA-MSR, and potential failure mode and effects analysis in manufacturing and assembly processes (PFMEA). It assists users in the identification and mitigation of risk by providing appropriate terms, requirements, rating charts, and worksheets. As a standard, this document contains requirements—”must”—and recommendations—”should”—to guide the user through the FMEA process. The FMEA process and documentation must comply with this standard as well as any corporate policy concerning this standard. Documented rationale and agreement with the customer are necessary for deviations in order to justify new work or changed methods during customer or third-party audit reviews.
This specification covers types and classes of polysulfide sealing compound supplied as a two-component system suitable for application by brush, or by extrusion gun, spatula brush, or roller.
This document establishes the minimum training and qualification requirements for ground-based aircraft deicing methods and procedures. All guidelines referred to herein are applicable only in conjunction with the applicable documents. Due to aerodynamic and other concerns, the application of deicing fluids shall be carried out in compliance with engine and aircraft manufacturers’ recommendations. The scope of training should be adjusted according to local demands. There are a wide variety of winter seasons and differences of the involvement between deicing operators, and therefore, the level and length of training should be adjusted accordingly. However, the minimum level of training shall be covered in all cases. As a rule of thumb, the amount of time spent in practical training should equal or exceed the amount of time spent in classroom training.
This specification covers butadiene acrylonitrile (NBR) rubber in the form of molded rings.
See Table 1.
This SAE Recommended Practice provides laboratory test procedures for testing headlamp aim test machines to verify their ability to aim or to inspect the aim of headlamps, fog lamps, and auxiliary high beam lamps. This specification does not apply to aiming devices of the kind covered by SAE J602. This specification does not apply to motorcycle headlamps.
This SAE Recommended Practice establishes minimum requirements for electric hourmeters for general vehicular applications.
This specification covers a premium aircraft-quality steel in the form of bars, forgings, mechanical tubing, flash welded rings up through 10.000 inches (254.00 mm) inclusive in diameter or least distance between parallel sides, and stock of any size for forging or flash welded rings.
This SAE Aerospace Information Report (AIR) discusses the often overlooked relationship between hot stamp marking and the environmental conditions that contribute aircraft wiring problems and discusses current beliefs of military service experts, regulatory agencies and industry standard writing bodies about the potential hazards imposed by the hot stamping process.
This SAE practice is intended for the sample preparation of test pieces for automotive wheels and wheel trim. The practice provides a consistent scribing method for use on test panels and or component parts with substrate chemical pretreatment and coating systems. Test specimens can then be subjected to various corrosion tests in order to evaluate performance without significant variations of the degree of exposure of the substrate. The scribing is used to create a break in the coating/finishing as can occur in the field through gravel and other damaging conditions. NOTE— Significant variability is attributed to surface contour, coating hardness/softness, operator reproducibility, and the scribing tool and it’s condition.
Items per page:
50
1 – 50 of 222741