Results
This SAE Standard applies to 12-volt lead-acid storage batteries that are designed specifically for start-stop operations in on-road passenger vehicles or light trucks. Included are definitions of terms, general testing recommendations, key performance characteristics, and life testing. Properties not unique to start-stop batteries should be tested according to SAE J537 or other applicable testing protocols.
This document outlines general requirements for the use of CFD methods for aerodynamic simulation of medium and heavy commercial ground vehicles weighing more than 10000 pounds. The document provides guidance for aerodynamic simulation with CFD methods to support current vehicle characterization, vehicle development, vehicle concept development, and vehicle component development. The guidelines presented in the document are related to Navier-Stokes and Lattice-Boltzmann based solvers. This document is only valid for the classes of CFD methods and applications mentioned. Other classes of methods and applications may or may not be appropriate to simulate the aerodynamics of medium and heavy commercial ground vehicle weighing more than 10000 pounds.
This specification covers non-silicone synthetic rubber sealing compounds supplied as a two-component or pre-mixed and frozen (PMF) system that cures at room temperature.
This Purchasing Specification (PS), AMS3970/3, specifies the batch release and delivery requirements for carbon fiber fabric epoxy prepreg used for repair. This specification is applicable only when the carbon fiber fabric epoxy prepreg is used as part of the repair system defined in AMS3970 and AMS3970/1. This specification also defines the procedure and requirements for storage life extension of materials purchased against this specification. It is only applicable for materials that are qualified against AMS3970 (refer to PRI QPL AMS3970) and shall be carried out within the responsibility of the purchaser and under control of its Quality organization.
The intent of this specification is for the procurement of the material listed on the QPL; therefore, no qualification or equivalency threshold values are provided. Users that intend to conduct a new material qualification or equivalency program must refer to the Quality Assurance section of the base specification, AMS6891.
This Purchasing Specification (PS) AMS3970/4 specifies the batch release and delivery requirements for film adhesive used for repair. This specification is applicable only when the film adhesive is used as part of the prepreg system as defined in AMS3970 and AMS3970/1. This specification also defines the procedure and requirements for storage life extension of materials purchased against this specification. It is only applicable for materials which are qualified and shall be carried out within the responsibility of the purchaser and under control of its Quality organization.
This specification covers a premium aircraft-quality, low-alloy steel in the form of bars, forgings, mechanical tubing, and forging stock.
AMS3970/2B gives specific information about the qualification program for carbon fiber fabric reinforced epoxy structural repair prepreg systems, curing under vacuum at 120 °C (250 °F), and a companion non-structural glass fabric prepreg used for repair of carbon fiber reinforced epoxy structures. The prepreg system shall include an epoxy film adhesive to be applied in a co-curing process with the prepreg for joint solid laminate and sandwich bonding.
This specification covers a corrosion- and heat-resistant nickel alloy in the form of bars, forgings, flash-welded rings under 4 inches (102 mm) in least cross-sectional dimension, and stock of any size for forging or flash-welded rings (see 8.3).
This specification covers a titanium alloy in the form of extruded bars, tubes, and shapes, flash-welded rings up through 4.000 square inches (25.81 cm2) cross section, and stock for flash-welded rings (see 8.6).
This Purchase Specification (PS), AMS3970/5, specifies the batch release and delivery requirements for the companion non-structural glass fiber fabric prepreg. This specification also defines the procedure and requirements for storage life extension of materials purchased against this specification. It is only applicable for materials which are qualified and shall be carried out within the responsibility of the purchaser and under control of its Quality organization.
The purpose of this document is to establish guidelines for determining the critical R134a and R1234yf refrigerant charge for off-road, self-propelled work machines as defined in SAE J1116 and agricultural tractors as defined in ANSI/ASAE S390. It will develop a minimum to maximum refrigerant charge range in which the HVAC system can maintain proper operation. Operating conditions and characteristics of the equipment will influence the optimum charge. Since these conditions and characteristics vary greatly from one application to another, careful consideration should be taken to determine the optimum R134a and R1234yf refrigerant charge for the HVAC system.
This SAE Standard provides general and dimensional specifications for beaded ends and hose fittings. These connections are intended for general applications in low-pressure automotive and hydraulic systems on automotive, industrial, and commercial products. The fittings shown are designed to be used with hoses that are intended to be retained by hose clamps. It is recommended that where step sizes or additional types of fittings are required they be designed to conform with the specifications of this document insofar as they may apply. The following general specifications shall supplement the dimensional data contained in the tables with respect to all unspecified detail.
This SAE Aerospace Standard (AS) defines the requirements for polytetrafluoroethylene (PTFE) lined, metallic reinforced, hose assemblies suitable for use in aerospace hydraulic, fuel, and lubricating oil systems at temperatures between -67 and 450 °F for Class I assemblies, -67 and 275 °F for Class II assemblies, and at nominal pressures up to 1500 psi. The hose assemblies are also suitable for use within the same temperature and pressure limitations in aerospace pneumatic systems where some gaseous diffusion through the wall of the PTFE liner can be tolerated. The use of these hose assemblies in pneumatic storage systems is not recommended. In addition, installations in which the limits specified herein are exceeded, or in which the application is not covered specifically by this standard (for example, oxygen), shall be subject to the approval of the procuring activity.
The intent of this specification is for the procurement of carbon fiber and fiberglass epoxy prepreg products with 350 °F (177 °C) cure for aerospace applications; therefore, no qualification or equivalency threshold values are provided. Users that intend to conduct a new material qualification or equivalency program must refer to the production quality assurance section (see 4.3) of this base specification, AMS6891.
Electroplating is a process whereby an object is coated with one or more relatively thin, tightly adherent layers of one or more metals. It is accomplished by placing the object to be coated on a plating rack or a fixture, or in a basket or in a rotating container in such a manner that a suitable current may flow through it, and then immersing it in a series of solutions and rinses in planned sequence. The advantage to be gained by electroplating may be considerable; broadly speaking, the process is used when it is desired to endow the basis material (selected for cost, material conservation, and physical property reasons) with surface properties it does not possess. It should be noted that although electroplating is the most widely used process for applying metals to a substrate, they may also be applied by spraying, vacuum deposition, cladding, hot dipping, chemical reduction, mechanical plating, etc. The purpose for applying an electroplate and the metals used for various
This specification covers the specific requirements for 2024 aluminum alloy bar, rod and wire produced by rolling, drawing or cold finishing.
This specification covers the specific requirements for aluminum alloy 7075-T76 bar, rod, and shapes produced by extrusion (See AMS-QQ-A-200/11 for specific requirements for 7075 extrusions in other tempers).
The importance of reliability in design engineering has significantly grown since the early 1960’s. Competition has been a primary driver in this growth. The three realities of competition today are: world class quality and reliability, cost-effectiveness, and fast time-to-market. Formerly, companies could effectively compete if they could achieve at least two of these features in their products and product development processes, often at the expense of the third. However, customers today, whether military, aerospace, or commercial, have been sensitized to a higher level of expectation and demand products that are highly reliable, yet affordable. Product development practices are shifting in response to this higher level of expectation. Today, there is seldom time, or necessary resources to extensively test, analyze, and fix to achieve high quality and reliability. It is also true that the rapid growth in technology prevents the accumulation of historical data on the field performance
The Gauge Evaluation Procedure Task Force was formed by the Non-Hydraulic Hose Committee to develop a gauge evaluation procedure to be used when evaluating the capability of gauges used for hose measurement. The use of a standard method for gauge evaluation will help users easily compare equipment capability. The information provided in this recommendation is based on the methods used to produce the data presented in SAE J1759 and J2605.
This SAE Aerospace Recommended Practice (ARP) is intended to be a guide for defining automatic test equipment (ATE) methods to be used in performing electrical acceptance tests to ensure repeatability and compatibility of results between manufacturers and between manufacturer and user.
This standard establishes the common requirements for training of DPRV personnel for use at all levels of the aerospace engine supply chain. This standard shall apply when an organization elects to delegate product release verification by contractual flow down to its suppliers (reference 9100 and 9110 standards) and to perform product acceptance on its behalf. It is intended that organizations specify their DPRV requirements through the application of AS9117. While the delegating organization will use the AS13001 standard as the baseline for establishing DPRV process and product training, it may include additional contractual training requirements to meet its specific needs. The DPRV training material was primarily developed for aerospace engine supply chain requirements. However, this standard may also be used in other aerospace industry sectors where a DPRV process requiring specific training can be of benefit.
ARP4761A and its EUROCAE counterpart, ED-135, present guidelines for performing safety assessments of civil aircraft, systems, and equipment. They may be used when addressing compliance with certification requirements (e.g., 14 CFR/CS Parts 23, 25, 27, and 29 and 14 CFR Parts 33, 35, CS-E, and CS-P). ARP4761A/ED-135 may also be used to assist a company in meeting its own internal safety assessment standards. While the safety assessment processes described are primarily associated with civil aircraft, systems, and equipment, these processes may be used in many other applications. The guidelines herein identify a systematic safety assessment process, but other processes may be equally effective. The processes described herein are usually applicable to the new designs or to existing designs that are affected by changes to design or functions. In the case of the implementation of existing design(s) in a derivative application, complementary means such as service experience in a similar
This specification covers a corrosion and heat-resistant steel in the form of welding wire.
This SAE Recommended Practice establishes the test procedure, environment, and instrumentation for determining the maximum sound level potential for motorcycles under wide open throttle acceleration and closed throttle deceleration.
This Information Report presents background and rationale for SAE Recommended Practice J1106, Laboratory Testing Machine and Procedures for Measuring the Steady Force and Moment Properties of Passenger Car Tires. The purpose of SAE J1106 is to define standards for equipment design and test procedures so that data from different laboratories can be directly compared. Whereas such standardization is not a requirement for testing associated with tire development, it is necessary in the context of vehicle design and tire selection problems. The basic approach employed in developing SAE J1106 was to consolidate and document existing technology as embodied in equipment and procedures currently employed for routine tire evaluations. Equipment and procedures whose current use is restricted to research applications were not considered. Research experience is discussed in this Information Report, however, to the extent deemed necessary to provide background and rationale for SAE J1106. Material
This standard describes the accepted methods used for preparing aerospace sealant test specimens for qualification and quality conformance or acceptance testing. AS5127/1 and AS5127/2 are to be used in conjunction with this document and the applicable AMS specifications.
The marine environment differs greatly from other environments in which hydraulics are used. This Recommended Practice provides hydraulic design considerations and criteria for the marine environment and is applicable to commercial vessels, military ships, and submersible vehicles. This document may be used for manned and un-manned vehicles.
Items per page:
50
1 – 50 of 221913