Results
This SAE Aerospace Recommended Practice (ARP) recommends a methodology to be used for the design, analysis and test evaluation of modern helicopter gas turbine propulsion system stability and transient response characteristics. This methodology utilizes the computational power of modern digital computers to more thoroughly analyze, simulate and bench-test the helicopter engine/rotor system speed control loop over the flight envelope. This up-front work results in significantly less effort expended during flight test and delivers a more effective system into service. The methodology presented herein is recommended for modern digital electronic propulsion control systems and also for traditional analog and hydromechanical systems.
This SAE Standard establishes a test method and a definition for disclosing the performance of suction/blower fans when applied to self-propelled sweepers that solely use a pneumatic conveyance means for the collection and transfer of “sweepings” into a collection hopper.
This SAE standard covers the minimum mechanical properties measured on separately cast test pieces of varying thickness and microstructural requirements for ductile iron castings used in automotive and allied industries. Castings may be specified in the as-cast or heat-treated condition. If castings are heat-treated, prior approval from the customer is required. The appendix provides general information on chemical composition, microstructure and casting mechanical properties, as well as other information for particular service conditions. In this standard SI units are primary and in-lb units are derived.
This SAE Standard applies to planning and mapping various types of information associated with directional boring/drilling machines. This type of planning and mapping information is typically used with horizontal directional drilling (HDD) machines as defined by ISO 21467:2023.
This Glossary is designed to serve persons who need to know the accepted meanings, within specific contexts, of the terminology used in reports, articles, regulations, and other materials dealing with aviation safety -- with particular reference to terms specific to human factors in aviation safety. It is assumed that some users of the Glossary will be familiar with the nomenclature of aviation, but will need information on the language of human factors in engineering as they apply to aviation safety. Others (for example, engineers and psychologists) will have fairly extensive knowledge of the terminology of their own and related disciplines, but will need authoritative definitions of technical terms specific to aviation. Within the foregoing general framework, the following guidelines for the inclusion of terms to be defined have been observed:
This SAE Aerospace Standard establishes the requirements for a V-retainer coupling, flanges, and seal suitable for joining high-pressure and high-temperature ducting in aircraft bleed air systems. The rigid coupling joint assembly, hereafter referred to as “the joint,” shall operate within the temperature range of -65 to +1200 °F.
This standard covers all types of oxygen breathing equipment used in non-military aircraft. It is intended that this standard supplements the requirements of the detail specification or drawings of specific components or assemblies (e.g., regulators, masks, cylinders, etc.). Where a conflict exists between this standard and detail specifications, detail specifications shall take precedence.
This SAE Recommended Practice establishes uniform engineering nomenclature for the most common wheel constructions, and their components used on passenger cars, light trucks, and multipurpose vehicles. These wheel constructions are welded disc wheels, cast wheels, forged wheels, composite wheels and hybrid wheels. This nomenclature and the accompanying drawings are intended to define fundamental wheel terms rather than to provide a comprehensive tabulation of all wheel design types.
This SAE Information Report applies to structural integrity, performance, drivability, and serviceability of personally licensed vehicles not exceeding 10000 pounds GVWR such as sedans, crossovers, SUVs, MPVs, light trucks, and van-type vehicles that are powered by gas and alternative fuel such as electric, plug-in hybrid, or hybrid technologies. It provides engineering direction to vehicle modifiers in a manner that does not limit innovation, and it specifies procedures for preparing vehicles to enhance safety during vehicle modifications. It further provides guidance and recommendations for the minimum acceptable design requirements and performance criteria on general and specific structural modifications, thereby allowing consumers and third-party payers the ability to obtain and purchase equipment that meets or exceeds the performance and safety of the OEM production vehicle.
This specification covers a titanium alloy in the form of welding wire (see 8.5).
This specification covers a titanium alloy in the form of bars, wire, forgings, and flash-welded rings up through 3.999 inches (101.57 mm), inclusive, and stock for forging, flash-welded rings, or heading (see 8.6).
This specification covers an aluminum alloy in the form of honeycomb core in a non-hexagonal, flexible cell configuration with the core being treated for increased corrosion resistance and furnished only in the expanded form (see 8.5).
This specification covers one grade of commercially pure titanium in the form of wire for welding filler metal (see 8.5).
This glossary provides accepted definitions for terms commonly used by manufacturers and users of electric wire and cable, and their components, intended for use on aerospace vehicles.
This SAE Recommended Practice describes a marking system to distinguish long-stroke from standard stroke for service, parking, and combination air-brake actuators, and components. Said actuators are used for applying cam type foundation brakes by slack adjuster means.
This SAE Standard pertains to off-road, self-propelled work machines as defined in categories one through five of SAE J1116. It is intended to provide engineers and designers with information in order that access openings provided in equipment and machinery for purposes of inspection, adjustment, and maintenance are made large enough for the intended function by the person in the field or shop.
This specification covers a palladium-silver alloy in the form of round wire 0.004 to 0.080 inch (0.10 to 2.03 mm), inclusive, in nominal diameter (see 8.5).
This specification covers an aluminum alloy in the form of plate 0.250 to 4.000 inches (6.35 to 102.0 mm), inclusive, in nominal thickness (see 8.5).
This specification covers an aluminum alloy in the form of extruded bars, rods, wire, profiles, and tubing up to 5.000 inches (127.00 mm), inclusive, in nominal diameter or least thickness between parallel sides (bars, rods, wire, profiles) or nominal wall thickness (tubing) (see 8.5).
Electric and alternative fueled vehicles present different hazards for first and second responders than conventional gasoline internal combustion engines. Hydrogen vehicles (H2V) including Fuel Cell Vehicles (FCVs) involved in incidents may present unique hazards associated with the fuel storage and high voltage systems. The electrical hazards associated with the high voltage systems of hybrid-electric vehicles and FCVs are already addressed in the parent document, SAE J2990. This Recommended Practice therefore addresses electric issues by reference to SAE J2990 and supplements SAE J2990 to address the potential consequences associated with hydrogen vehicle incidents and suggest common procedures to help protect emergency responders, tow and/or recovery, storage, repair, and salvage personnel after an incident has occurred. Industry design standards and tools were studied and where appropriate, suggested for responsible organizations to implement.
This SAE Recommended Practice establishes a uniform fluid specification for reference usage in specific documents, such as fluid power component test procedures, where a fluid designation is required.
This SAE Aerospace Recommended Practice (ARP) provides information and guidance for the control of hazardous laser exposure in the navigable airspace. This ARP does not address techniques that pilots can apply to mitigate laser illuminations during a critical phase of flight. Such mitigation strategies are described in ARP6378.
The verification matrix (VM) in this slash sheet is intended for use to establish compliance to AS6174A. This slash sheet is applicable to AS6174A. Nothing in this slash sheet, however, supersedes applicable laws and regulations, unless a specific exemption has been obtained through judicial/legal channels.
This specification covers a titanium alloy in the form of wire for welding filler metal (see 8.5).
This document establishes safety limits and performance requirements for gaseous hydrogen fuel dispensers used to fuel Hydrogen Powered Industrial Trucks (HPITs). It also describes several example fueling methods for gaseous hydrogen dispensers serving HPIT vehicles. SAE J2601-3 offers performance based fueling methods and provides guidance to fueling system builders as well as suppliers of hydrogen powered industrial trucks and operators of the hydrogen powered vehicle fleet(s). This fueling protocol for HPITs can support a wide range of hydrogen fuel cell hybrid electric vehicles including fork lifts, tractors, pallet jacks, on and off road utility, and specialty vehicles of all types. The mechanical connector geometry for H25 and H35 connectors are defined in SAE J2600 Compressed Hydrogen Surface Vehicle Refueling Connection Devices. Multiple fueling methods are described in this document and include: 1 Fill to Service Pressure with fixed area flow-limiting device 2 Fill to Target
This document defines the requirements for polytetrafluoroethylene (PTFE) lined, para-aramid reinforced, hose assemblies suitable for use in 275 °F (135 °C), 5080 psi (35000 kPa) aircraft hydraulic systems.
This SAE Recommended Practice establishes a uniform fluid specification for reference usage in specific documents, such as fluid power component test procedures, where a fluid designation is required.
Develop terminology and definitions specifically for the automotive industry that defines greener and more sustainable materials and practices. The document will provide information and context for how and where the terms are used in the auto sector. In some cases, there may be more than one definition provided as some terms have different meanings in different countries.
This document is not a standard, it is a candidate for a standard being submitted to SAE for their consideration as a comment to SAE J2735. The term SAE J2735 SE candidate is used within this document to refer to this submission. This document specifies dialogs, messages, and the data frames and data elements that make up the messages specifically for use by applications intended to utilize the 5.9 GHz Dedicated Short Range Communications for Wireless Access in Vehicular Environments (DSRC/WAVE, referenced in this document simply as “DSRC"), communications systems. Although the scope of this Standard is focused on DSRC, these dialogs, messages, data frames and data elements have been designed, to the extent possible, to be of use for applications that may be deployed in conjunction with other wireless communications technologies. This standard therefore specifies the definitive message structure and provides sufficient background information to allow readers to properly interpret the
This SAE Standard covers the minimum requirements for metric sizes of nonmetallic tubing as manufactured for use in air brake systems. Nonreinforced products are designated type A and reinforced products type B. It is not intended to cover tubing for any portion of the system that operates below -40 °C (-40 °F), above +93 °C (+200 °F), above a maximum working gage pressure of 1.0 MPa (150 psi), or in an area subject to attack by battery acid. This tubing is intended for use in the brake system for connections that maintain a basically fixed relationship between components during vehicle operation. Coiled tube assemblies required for those installations where flexing occurs are covered by this standard and SAE J1131 to the extent of setting minimum requirements on the essentially straight tube and tube fitting connections, which are used in the construction of such assemblies.2 NOTE—As all elements of SAE J1394 are being merged into SAE J844, two separate documents are no longer
This SAE Recommended Practice summarizes the composition of modern automotive gasolines, the significance of their physical and chemical characteristics, and the pertinent test methods for defining or evaluating these properties.
Items per page:
50
1 – 50 of 219833