Results
This AIR provides information about the specific requirements for missile hydraulic pumps and their associated power sources.
This specification covers materials in the form of a liquid used to remove smut from aluminum surfaces treated with etch-type oxidation and corrosion removers.
This SAE Standard establishes the minimum performance requirements for electrical distribution systems for use in dollies and trailers in single or multiple configurations for 12 VDC nominal applications.
This SAE Recommended Practice specifies the design and/or evaluation with the specific equipment, conditions, and methods for distributorless battery ignition systems intended for use in various internal combustion engines including automotive, marine, motorcycle, and utility engine applications. The test procedures listed in this document are limited to measurements performed on a test bench only and do not include measurements made directly on engines or vehicles. This standard is not intended to supply information for battery ignition systems used in aircraft applications of any type.
This standard specifies the communications hardware and software requirements for fueling hydrogen surface vehicles (HSV), such as fuel cell vehicles, but may also be used where appropriate with heavy-duty vehicles (e.g., buses) and industrial trucks (e.g., forklifts) with compressed hydrogen storage. It contains a description of the communications hardware and communications protocol that may be used to refuel the HSV. The intent of this standard is to enable harmonized development and implementation of the hydrogen fueling interfaces. This standard is intended to be used in conjunction with the hydrogen fueling protocols in SAE J2601 and nozzles and receptacles conforming with SAE J2600 and ISO 17628. It may also be used with future hydrogen fueling protocols at the discretion of those fueling protocols.
This test method outlines a standard procedure for performing cyclic reversing load testing on oscillating sliding bearings. The wear data from these tests is to be used for qualification requirements and to establish bearing design criteria.
This standard presents the designer with sufficient information to fully define the configuration of the connection and to determine the limits of application for given conditions.
This SAE Standard was developed to provide a method for indicating the direction of engine rotation and numbering of engine cylinders. The document is intended for use in designing new engines to eliminate the differences which presently exist in industry.
This AIR provides guidance to the EMI test facility on how to check performance of the following types of EMI test equipment: Current probe Line Impedance Stabilization Network (LISN) Directional coupler Attenuator Cable loss Low noise preamplifier Rod antenna base Passive antennas All performance checks can be performed without software. A computer may be required to generate an electronic or hard copy of data. This is not to say that custom software might not be helpful; just that the procedures documented herein specifically eschew the necessity of automated operation.
This SAE Standard covers normalized electric-resistance welded, cold-drawn, single-wall, low-carbon steel pressure tubing intended for use as pressure lines and in other applications requiring tubing of a quality suitable for bending, flaring, forming, and brazing. In an effort to standardize within a global marketplace and ensuring that companies can remain competitive in an international market it is the intent to convert to metric tube sizes which will: Lead to one global system Guide users to preferred system Reduce complexity Eliminate inventory duplications
Corrosion control is always of concern to the designer of electronic enclosures. The use of EMI gaskets to provide shielding often creates requirements that are in conflict with ideal corrosion control. This SAE Aerospace Recommended Practice (ARP) presents a compatibility table (see Figure 1) which has as its objective a listing of metallic couples that are compatible from a corrosion aspect and which still maintain a low contact impedance.
This method is used to define the immunity of electric and electronic apparatus and equipment (products) to radiated electromagnetic (EM) energy. This method is based on injecting the calibrated radio frequency currents (voltages) into external conductors and/or internal circuits of the product under test, measuring the strength of the EM field generated by this product and evaluating its immunity to the external EM field on the basis of the data obtained. The method can be utilized only when it is physically possible to connect the injector to the conductors and/or circuits mentioned before. The method allows: Evaluating immunity of the product under test to external EM fields of the strength equal to a normalized one; Calculating the level of external EM field strength at which the given (including maximum permissible) induced currents or voltages are generated in the equipment under test, or solving the “opposite” task; Finding potentially “weak” points of the product design
This part of SAE J514 covers general and dimensional specifications for NPTF pipe adapters and 30 degree NPSM adapter unions. These fittings are intended for general application in hydraulic systems on industrial equipment and commercial products. These fittings are capable of providing leak-proof, full-flow connections in hydraulic systems operating at working pressures as specified in Table 6. Since many factors influence the pressure at which a hydraulic system will or will not perform satisfactorily, the values shown in Table 6 should not be construed as a guaranteed minimum. For any application, it is recommended that sufficient testing be conducted and reviewed by both the user and fitting manufacturer to assure that performance levels will be safe and satisfactory.
The purpose of this procedure is to establish a technique for reliably and repeatedly measuring the RF shielding characteristics of EMI gasket materials and EMI gaskets against various joint surfaces. The procedure is also used to test the reliability of the gasketed joint combinations after being subjected to hostile environments.
This guide provides detailed information, guidance, and methods related to the Federal Aviation Administration (FAA) Advisory Circular (AC) 20-158 and European Aviation Safety Agency (EASA) draft Advisory Material Joint (AMJ), both titled "The Certification of Aircraft Electrical and Electronic Systems for Operation in the High-Intensity Radiated Fields (HIRF) Environment". The AC provides acceptable means, but not the only means, of compliance with Title 14, Code of Federal Regulations (14 CFR) 23.1308, 25.1317, 27.1317, and 29.1317, High-Intensity Radiated Fields (HIRF) protection for Aircraft Electrical and Electronic Systems, and applicable FAA HIRF Special Conditions to prevent hazards to aircraft electrical and electronic systems due to HIRF produced by external transmitters. It is also intended for this guide to provide the same information, guidance, and methods to the European Aviation Safety Agency (EASA) interim HIRF policies certification requirements. This guide is neither
This specification, in conjunction with the general requirements for steel heat treatment covered in AMS2759, establishes the requirements and procedures for three classes of gas, vacuum, liquid, and low pressure (LPC) carburizing and related heat treatment of parts fabricated from carburizing grade steels. Parts made from steels other than those specified in the detail specifications may be heat treated in accordance with the applicable requirements using processing temperatures, times, and other parameters recommended by the material producer unless otherwise specified by the purchaser. This specification does not cover pack carburizing.
This specification covers an aircraft-quality, low-alloy steel in the form of welded tubing.
This specification covers established inch/pound manufacturing tolerances applicable to copper and copper alloy seamless tubing ordered to inch/pound dimensions. These tolerances apply to all conditions, unless otherwise noted. The term “exclusive” is used to apply only to the higher figure of a specified range.
This SAE Aerospace Information Report (AIR) describes the aspects of hydraulic system design and installation to minimize the effects of lightning. Techniques for effective electrical bonding, hydraulic system lightning protection, and lightning protection verification techniques are discussed.
This revision of AS6513 concerns conformance to the SAE Unmanned Systems (UxS) Control Segment (UCS) Architecture Revision B, designated AS6512B (or later). The superseded AS6513A concerned conformance to the previous UCS Architecture, designated AS6512A. This document is the authoritative specification within the UCS Architecture for establishing conformance requirements for UCS products. The conformance of UCS products is determined by assessing the conformance of the UCS Product Description to the UCS Architecture. The UCS Product Description includes test artifacts.
This specification covers a corrosion-resistant, premium aircraft-quality alloy steel in the form of bars, forgings, and stock for forging.
This specification covers a corrosion- and heat-resistant nickel alloy in the form of sheet, strip, and plate.
This specification covers a corrosion- and heat-resistant nickel alloy in the form of two types of tubing.
The scope of this report will document the various voltage levels and provide a rationale for each level as discussed and agreed to in the AE-7 committee.
This specification covers an aluminum alloy in the form of seamless, drawn tubing having a nominal wall thickness of 0.120 to 0.400 inch (3.00 to 10.00 mm), inclusive (see 8.5).
To provide the curved hose industry and their customers with a recommended practice for applying GD&T procedures to curved hoses and to provide generic curved hose drawings that represent the application of GD&T to typical curved hose parts. Dimensioning and Tolerancing will be in accordance with ASME Y14.5M.
SAE J3078/6 specifies a test method for simulating solar heating in the laboratory and measuring the radiant heat energy from a natural or simulated source. It is applicable to off-road self-propelled work machines as defined in SAE J1116 and tractors and machinery for agriculture and forestry as defined in ANSI/ASAE S390.
Items per page:
50
1 – 50 of 215880