Results
This SAE Information Report SAE J2836/6 establishes use cases for communication between plug-in electric vehicles and the EVSE for wireless energy transfer as specified in SAE J2954. It addresses the requirements for communications between the on-board charging system and the wireless EV supply equipment (WEVSE) in support of detection of the WEVSE, the charging process, and monitoring of the charging process. Since the communication to the charging infrastructure and the power grid for smart charging will also be communicated by the WEVSE to the EV over the wireless interface, these requirements are also covered. However, the processes and procedures are expected to be identical to those specified for V2G communications specified in SAE J2836/1. Where relevant, the specification notes interactions that may be required between the vehicle and vehicle operator, but does not formally specify them. Similarly, communications between the on-board charging sub-system and the on-board vehicle
This document provides recommendations involving BEV battery data retention and battery design that enhance the potential for BEV battery reuse and serviceability and that can improve recyclability. These recommendations have been developed by a group of professionals skilled in the secondary-use of batteries and in the research, development, and manufacture of BEV batteries and battery systems.
This specification covers a blend of chromium carbide and a nickel-chromium alloy in the form of powder.
The automotive air-conditioning service ports task force conducted a field survey with MACS (Mobile Air Climate Systems Association) in June 2021. The scope of this survey was to determine the types of failures reported primarily at member service shops related to automotive air-conditioning service ports.
This Information Report relates to a special class of automotive adaptive equipment which consists of modifications to the power brake booster systems provided as original equipment of motor vehicles. These modifications are generically called "Reduced Effort Power Brakes" (REPB) The purpose of the modification is to lower the amount of driver effort required to apply the brakes. Retention of reliability, ease of use and maintainability for disabled drivers, passengers, and the general public is of primary concern. Reduced Effort Power Brake modifications should be qualified by the tests referenced in the Recommended Test Procedure. The tests set forth in that procedure should be applied, and failure of a Reduced Effort Power Brake modification to meet those tests should disqualify the modification from the claim of meeting the specifications of this Information Report. Because this is an Information Report, the numerical values for performance measurements presented in this report and
This SAE Recommended Practice is intended to provide basic information on properties and characteristics of high-strength carbon and alloy steels which have been subjected to special die drawing. This includes both cold drawing with heavier-than-normal drafts and die drawing at elevated temperatures.
This SAE Standard is intended to serve as a guide for the collection of physical, mechanical, and thermal properties of fiber-reinforced polymer composite materials for automotive structural applications. This document attempts to utilize test methods applicable to the widest range of structural materials and processes without compromising the integrity of the data being sought. A summary of the material characterization is shown in Section 15.
This SAE Recommended Practice establishes uniform minimum labeling for disc wheels and demountable rims used in truck, bus, and trailer applications.
This specification covers established manufacturing tolerances applicable to titanium and titanium alloy extruded bars, rods, and shapes. These tolerances apply to all conditions, unless otherwise noted. The term “excl” applies only to the higher figure of the specified range.
This SAE Standard gives methods for testing and evaluating performance of the SAE 100R series of hydraulic hose and hose assemblies (hose and attached end fittings) used in hydraulic fluid power systems. Specific tests and performance criteria for evaluating hose assemblies used in hydraulic service are in accordance with the requirements for hose in the respective specifications of SAE J517. This document further establishes a uniform means of testing and evaluating performance of hydraulic hose assemblies.
This SAE Recommended Practice provides a procedure for measuring quantitatively the physical characteristics of linear impactors that are believed to effect impact test accuracy, repeatability, and reproducibility. Suggested values and tolerance are also provided for specific applications of linear impactor testing (i.e., ejection mitigation tests, head form impact tests, body block tests). Two functional groups of linear impactors are considered: those whose function is related primarily to displacement, and those related to measuring acceleration or force.
This SAE Recommended Practice is applicable to pneumatic Passenger Car “P” Type, Light Truck Metric, and Light Truck High Flotation tires, or similar tires approved by bodies other than Tire & Rim Association. The methodology is applicable within normal operating ranges of vertical load and inflation pressure, and for velocities between 115 km/h and 15 km/h (71 mph and 9 mph) during a relatively short duration event such as a coastdown. This procedure is applicable only to operation in the free-rolling mode at zero slip and camber angle for ambient temperatures between 20 °C and 28 °C (68 °F and 82 °F) and for surfaces with diameters of 1.2 m (48 in) diameter or greater. Details regarding the equipment, tires, and test methods used specifically for validation of this document are included in Appendix A. Two basic measurement methods covered by this document are as follows:
This SAE Recommended Practice provides minimum performance requirements and uniform laboratory procedures for fatigue testing of disc wheels, demountable rims, and bolt-together divided wheels intended for normal highway use on military trucks, buses, truck-trailers, and multipurpose vehicles. Users may establish design criteria exceeding the minimum performance requirement for added confidence in a design. For other (non-military) wheels and rims intended for normal highway use on trucks and buses, refer to SAE J267. For wheels intended for normal highway and temporary use on passenger cars, light trucks, and multipurpose vehicles, refer to SAE J328. For wheels used on trailers drawn by passenger cars, light trucks, or multipurpose vehicles, refer to SAE J1204. This document does not cover off-highway or other special application wheels and rims.
This SAE Standard serves as a guide for testing procedures of automotive 12 V storage batteries. The information contained herein was originally developed based on traditional ICE operation but can be more broadly applicable to other vehicle architectures. Although the test procedures contained herein are written from the standpoint of a 12 V nominal battery, they can be scaled for batteries with different nominal voltages.
This SAE Recommended Practice pertains to liquid level determination for any fluid compartment of off-road work machines as defined in SAE J1116 and ISO 6165.
This SAE Recommended Practice establishes the antilock brake system (ABS) sensor interface and envelope dimensions for standardizing the location of the ABS rings mounted on or integral to the inboard end of spoke wheels, hubs, rotors, and hub-rotor assemblies on the following axle designations as defined in SAE J1842. a FF b FL c FC d FH e L f R g U h W j N k P
This SAE Recommended Practice defines key terms used in the description and analysis of video based driver eye glance behavior, as well as guidance in the analysis of that data. The information provided in this practiced is intended to provide consistency for terms, definitions, and analysis techniques. This practice is to be used in laboratory, driving simulator, and on-road evaluations of how people drive, with particular emphasis on evaluating Driver Vehicle Interfaces (DVIs; e.g., in-vehicle multimedia systems, controls and displays). In terms of how such data are reduced, this version only concerns manual video-based techniques. However, even in its current form, the practice should be useful for describing the performance of automated sensors (eye trackers) and automated reduction (computer vision).
This SAE Recommended Practice applies to excavators and backhoe loaders, as defined in ISO 6165.
This SAE Standard provides a means for specifying or describing the pertinent properties of fiberboards for automotive applications. The materials normally specified by this standard are defined in SAE J947. The test methods commonly used for fiberboards are defined in SAE J315.
This SAE Standard applies to hydraulic directional control valves as applied to self-propelled work machines referenced in SAE J1116. It describes a laboratory test procedure for evaluating: a Flow versus pressure drop b Leakage rate c Operating effort d Metering characteristics versus spool travel, pilot pressure, or electrical current e Relief valve characteristics The document applies to single and multiple section hydraulic directional control valves. This document illustrates axial, manually operated valves although the test procedure is applicable to other input forms such as rotary actuation, electric current, hydraulic or pneumatic pressure. Performance characteristics such as metering hysteresis or dynamic response may have a significant effect on some of these tests.
This SAE Surface Vehicle Information Report identifies and defines the drawings and parts relating to the use of the Hybrid III Large Male Test Dummy.
Items per page:
50
1 – 50 of 219709