Results
This specification covers a low-alloy steel in the form of bars, forgings, mechanical tubing, and forging or tubing stock.
This supplement forms a part of SAE Aerospace Specification AS85421. It shall be used to identify fitting standards citing this procurement specification.
This SAE Standard establishes the test procedure, environment, and instrumentation for determining the sound levels of snowmobiles in the stationary test mode. This test method is intended to provide an accurate measurement of exhaust and other engine noise and may be used to evaluate new and in-use snowmobiles to determine compliance with noise control regulations. Sound level measurements obtained with this test method are not intended as an engineering determination of overall machine noise. For this purpose, the use of SAE J192 is recommended.
The thermocouple design recommended herein is presented as one for which the correction to the observed emf, because of thermal conduction along the stem and wires, is within the limits presented in the accompanying figure. On referring to the figure, it is seen that no restriction is placed upon the diameter of the thermocouple or stem, and the longitudinal dimensions are expressed in terms of wire and stem diameters. The type of stem, such as packed ceramic stock, refractory insulating tubing, etc., also is left open to choice. Thus the sizes of wires and supporting stems may be varied over wide ranges to match particular requirements where conduction errors are to be limited or controlled.
This specification covers three types of aircraft position lights.
This SAE Recommended Practice describes the test procedures for conducting quasi-static cab roof strength tests for heavy-truck applications. Its purpose is to establish recommended test procedures that will standardize the procedure for heavy trucks. Descriptions of the test setup, test instrumentation, photographic/video coverage, and test fixtures are included.
This SAE Standard provides minimum requirements and performance criteria for devices to prevent runaway snowmobiles due to malfunction of the speed control system.
ARP4761A and its EUROCAE counterpart, ED-135, present guidelines for performing safety assessments of civil aircraft, systems, and equipment. They may be used when addressing compliance with certification requirements (e.g., 14 CFR/CS Parts 23, 25, 27, and 29 and 14 CFR Parts 33, 35, CS-E, and CS-P). ARP4761A/ED-135 may also be used to assist a company in meeting its own internal safety assessment standards. While the safety assessment processes described are primarily associated with civil aircraft, systems, and equipment, these processes may be used in many other applications. The guidelines herein identify a systematic safety assessment process, but other processes may be equally effective. The processes described herein are usually applicable to the new designs or to existing designs that are affected by changes to design or functions. In the case of the implementation of existing design(s) in a derivative application, complementary means such as service experience in a similar
This specification covers a corrosion-resistant steel in the form of investment castings homogenized and solution and precipitation heat treated to 180 ksi (1241 MPa) tensile strength.
The intent of this standard is to establish a framework to assure that all evaporators conforming to its requirements demonstrate an acceptable health and safety environment for vehicle occupants as determined from the completed risk assessment. R-744 and low pressure (i.e., non-transcritical refrigerants with a critical temperature between 85 and 120 °C) mobile air conditioning (MAC) refrigerant evaporators shall meet the testing and labeling requirements of this standard. SAE J639 contains a list of all refrigerants considered acceptable for use in mobile thermal systems for which this standard applies when the refrigerant is used in a direct expansion architecture. SAE J639 also requires an assessment to be performed to minimize reasonable risks in MAC systems. The evaporator (as designed and manufactured) shall be part of that risk assessment, and it is the responsibility of the vehicle manufacturer to ensure all relevant aspects of the evaporator are included. It is the
This specification covers an aluminum alloy in the form of plate 0.500 to 4.500 inches (12.7 to 114.3 mm), inclusive, in nominal thickness (see 8.5).
The Dryseal American Standard Taper Pipe Thread, the Dryseal American Fuel Internal Straight Pipe Thread and the Dryseal American Intermediate Internal Straight Pipe Thread covered by this standard conform with the American Standard ASA-B2.2. The Dryseal SAE-Short Taper Pipe Thread in this standard conforms with the Dryseal American Standard Taper Pipe Thread except for the length of thread, which is shortened for increased clearance and economy of material. The significant feature of the Dryseal thread is controlled truncation at the crest and root to assure metal to metal contact coincident with or prior to flank contact. Contact at the crest and root prevents spiral leakage and insures pressure-tight joints without the use of a lubricant or sealer. Lubricants, if not functionally objectionable, may be used to minimize the possibility of galling in assembly.
This SAE Standard specifies the performance tests and requirements for hydraulic brake hose assemblies used in the hydraulic braking system of a road vehicle. It also specifies the methods used for identification of the hose manufacturer. This document applies to brake hose assemblies made of a hose fabricated from yarn and natural or synthetic elastomers and assembled with metal end fittings for use with nonpetroleum-base brake fluids as specified in SAE J1703, SAE J1704 and SAE J1705. The nominal internal diameter of the brake hose shall fall within one of the following values: a less than 4 mm (1/8 in or less) b 4 to 5 mm (3/16 in)
This standard includes ISO 9001:20152 quality management system requirements and specifies additional aviation, space, and defense industry requirements, definitions, and notes. It is emphasized that the requirements specified in this standard are complementary (not alternative) to customer and applicable statutory and regulatory requirements. If there is a conflict between the requirements of this standard and customer or applicable statutory or regulatory requirements, the latter shall take precedence. This International Standard specifies requirements for a quality management system when an organization: a needs to demonstrate its ability to consistently provide products and services that meet customer and applicable statutory and regulatory requirements, and b aims to enhance customer satisfaction through the effective application of the system, including processes for improvement of the system and the assurance of conformity to customer and applicable statutory and regulatory
This specification covers an aluminum alloy in the form of castings (see 8.10).
This specification covers a premium aircraft-quality, low-alloy steel in the form of bars, forgings, and mechanical tubing 225 square inches (1452 cm2) and under in cross-sectional area and forging stock of any size.
This SAE Information Report discusses the significant factors which measure the effectiveness of the total occupant restraint system in commonly encountered collision configurations. The total system includes the components which affect occupant injury by influencing the manner in which the collision energy management is accomplished. In addition to the elements that contribute to impact attenuation, consideration must be given to factors that encourage maximum use, such as comfort, reliability, appearance, and convenience. Hence, system evaluation necessarily involves consideration of the complete vehicle.
This part of SAE J514 covers general and dimensional specifications for NPTF pipe adapters and 30 degree NPSM adapter unions. These fittings are intended for general application in hydraulic systems on industrial equipment and commercial products. These fittings are capable of providing leak-proof, full-flow connections in hydraulic systems operating at working pressures as specified in Table 6. Since many factors influence the pressure at which a hydraulic system will or will not perform satisfactorily, the values shown in Table 6 should not be construed as a guaranteed minimum. For any application, it is recommended that sufficient testing be conducted and reviewed by both the user and fitting manufacturer to assure that performance levels will be safe and satisfactory.
This SAE Recommended Practice provides test procedures, requirements, and guidelines for side turn signal lamps intended for use on vehicles 12 m or more in overall length, except pole trailers. Side turn signal lamps conforming to the requirements of this document may be used on other large vehicles such as trucks, truck tractors, buses, and other applications where this type of lighting device is desirable.
This SAE Standard provides basic information on the International System of Units, abbreviated SI in all languages, and its application in engineering practice and measurement unit usage.
The landing gear system is a major and safety critical airframe system that needs to be integrated efficiently to meet the overall aircraft program goals of minimizing the penalties of weight, cost, dispatch reliability and maintenance. As the landing gear system business develops and large-scale teaming arrangements and acquisitions become increasingly common, it may be desirable in some instances to procure an Integrated Landing Gear System. This document provides guidelines and useful references for developing an integrated landing gear system for an aircraft. The document structure is divided into four sections: Landing Gear System Configuration Requirements (Section 3) Landing Gear System Functional Requirements (Section 4) Landing Gear System Integrity Requirements (Section 5) Landing Gear System Program Requirements (Section 6) The landing gear system encompasses all landing gear structural and subsystem elements. Structural elements include shock struts, truck beams, torsion
The process detailed within this document is generic and applies to the entire end-to-end health management capability, covering both on-board and on-ground elements, in both commercial and military applications throughout their lifecycle. This ARP addresses a gap in guidance related to usage of ground-based health management equipment for airworthiness credit, ensuring a level of integrity commensurate with the potential aircraft-level consequences of the relevant failure conditions. The practical application of this standardized process is detailed in the form of a checklist. The on-board elements described here are typically the source of the data acquisition used for off-board analysis. The on-board aspects relating to airworthiness and/or safety of flight, e.g., pilot notification, are addressed by existing guidance and policy documents. If a proposed health management capability for airworthiness credit involves modification of the on-board systems, the substantiation of those
This specification covers materials in the form of a liquid used to remove smut from aluminum surfaces treated with etch-type oxidation and corrosion removers.
Items per page:
50
1 – 50 of 221110