Results
This document defines the test procedures and performance limits of steady state and transient voltage characteristics for 12 V, 24 V, or 48 V electrical power generating systems used in commercial ground vehicles.
This specification covers a low-alloy steel in the form of bars, forgings, mechanical tubing, and forging or tubing stock.
This SAE Aerospace Standard (AS) contains landing gear strength and rigidity requirements which, in combination with other applicable specifications, define the structural design, analysis, test, and data requirements for fixed wing piloted airplanes. These requirements include, but are not limited to, the following: a General specifications: 1 The shock-absorption characteristics and strength of landing-gear units and the strength and rigidity of their control systems and of their carry-through structures. Requirements for wheels, tires, and brakes as they affect air vehicle ground loads are also included. 2 The strength of structures integral with the airplane provided for transmitting catapulting forces to the airplanes, and for engaging shipboard and shore-based arresting gear, and barricades. 3 The strength of anchor-line clamps, and the airplane strength for hoisting, jacking, towing, tie-down, and other ground- or deck-handling conditions. 4 Structural design, analysis, and test
This SAE Aerospace Standard (AS) establishes a Generic Open Architecture (GOA) Framework for application independent hardware/software systems. This document defines the interface classes for the GOA Framework. Supplemental documents define the guidelines for applying the GOA Framework to specific applications.
This document covers flexible and semiflexible, reinforced and unreinforced air hoses fabricated from laminated and impregnated fabric, intended for use in aircraft heating, air conditioning, ventilating, defrosting, and/or deicing systems.
This specification covers a low-alloy steel in the form of bare welding wire. Type 2 - copper coated wire was removed from this document (see 8.4).
This SAE Aerospace Standard (AS) aims at identifying the design criteria and testing methods adequate to guarantee the ultimate load and operational dependability of cargo restraint strap assemblies with a typical 22250 N (5000 lbf) rated ultimate tension load capability, as used by the airline industry in order to restrain cargo on board civil transport aircraft during flight: a cargo loaded and tied down onto airworthiness certified air cargo pallets, themselves restrained into aircraft lower deck or main/upper deck cargo systems and meeting the requirements of NAS 3610 or AS36100, or b non-unitized individual pieces of cargo, or pieces of, cargo placed onto an unrestrained (“floating”) pallet into either lower deck or main deck containerized cargo compartments of an aircraft.
This paper was prepared to support supersession of MIL-S-8879C with Screw Thread Conformity Task Force selected industry standard AS8879C, published by the Society of Automotive Engineers (SAE). Other documentation changes will be covered by separate papers. Separate papers are anticipated for thread gaging issues, and thread gage calibration procedures. The STC-TF decided that the thread design standard needed to be completed before thread gage definition could be addressed. Thread gage definition has to be known before calibration procedures can be addressed.
This document is limited to the aerospace industry, where an approved manufacturer requests a supplier to ship an article against the approved manufacturer’s quality system directly to a customer. The direct ship process is not required or applicable to standard parts or military parts. In this process, the approved manufacturer is responsible for assurance that the article conforms to type design information.
This aerospace specification defines the requirements for a threadless, flexible, conductive, self-bonding coupling assembly which, when installed on fixed cavity ferrules, provides a flexible, current carrying connection for joining tubing and components in aircraft fuel, vent and other systems. The assembled coupling is designed to provide interchangeability of parts and components between qualified manufacturers for the service life of the aircraft system. The assembled coupling is for use from -65 to +200 °F at nominal operating pressures (125 psig for -08 through -64 and 30 psig for -72 through -88). This aerospace specification is a departure from prior qualification practices for assembled couplings. Prior practice sought to validate this type of assembled coupling design by conducting a sequence of tests on sets of coupling assemblies. There were multiple test sequences and each was conducted on a different set of coupling assemblies. Each of these test sequences challenged a
This SAE Standard covers complete general and dimensional specifications for refrigeration tube fittings of the flare type specified in Figures 1 to 42 and Tables 1 to 15. These fittings are intended for general use with flared annealed copper tubing in refrigeration applications. Dimensions of single and double 45 degree flares on tubing to be used in conjunction with these fittings are given in Figure 2 and Table 1 of SAE J533. The following general specifications supplement the dimensional data contained in Tables 1 to 15 with respect to all unspecified details.
Electric and alternative fueled vehicles present different hazards for first and second responders than conventional gasoline internal combustion engines. Hydrogen vehicles (H2V) including Fuel Cell Vehicles (FCVs) involved in incidents may present unique hazards associated with the fuel storage and high voltage systems. The electrical hazards associated with the high voltage systems of hybrid-electric vehicles and FCVs are already addressed in the parent document, SAE J2990. This Recommended Practice therefore addresses electric issues by reference to SAE J2990 and supplements SAE J2990 to address the potential consequences associated with hydrogen vehicle incidents and suggest common procedures to help protect emergency responders, tow and/or recovery, storage, repair, and salvage personnel after an incident has occurred. Industry design standards and tools were studied and where appropriate, suggested for responsible organizations to implement.
This SAE Recommended Practice establishes uniform engineering nomenclature for the most common wheel constructions, and their components used on passenger cars, light trucks, and multipurpose vehicles. These wheel constructions are welded disc wheels, cast wheels, forged wheels, composite wheels and hybrid wheels. This nomenclature and the accompanying drawings are intended to define fundamental wheel terms rather than to provide a comprehensive tabulation of all wheel design types.
This SAE Standard applies to planning and mapping various types of information associated with directional boring/drilling machines. This type of planning and mapping information is typically used with horizontal directional drilling (HDD) machines as defined by ISO 21467:2023.
This SAE Recommended Practice is aimed at ensuring high-quality products of anodized aluminum automotive components in terms of durability and appearance. Decorative sulfuric acid anodizing has been well developed over the last several decades in the aluminum industry. Exterior and interior performance demonstrated that parts processed to this document meet long-term durability requirements. Since the treatment of processing variables is outside the scope of this document, it is important for applicators of this coating to develop an intimate knowledge of their process, and control all parameters that affect the quality of the end product. The use of techniques such as statistical process control (SPC), capability studies, design of experiments, process optimization, etc., are critical to produce material of consistently high quality.
This SAE Information Report applies to structural integrity, performance, drivability, and serviceability of personally licensed vehicles not exceeding 10000 pounds GVWR such as sedans, crossovers, SUVs, MPVs, light trucks, and van-type vehicles that are powered by gas and alternative fuel such as electric, plug-in hybrid, or hybrid technologies. It provides engineering direction to vehicle modifiers in a manner that does not limit innovation, and it specifies procedures for preparing vehicles to enhance safety during vehicle modifications. It further provides guidance and recommendations for the minimum acceptable design requirements and performance criteria on general and specific structural modifications, thereby allowing consumers and third-party payers the ability to obtain and purchase equipment that meets or exceeds the performance and safety of the OEM production vehicle.
This document provides nomenclature and references to related documents for heavy vehicle event data recorders (HVEDR) for heavy-duty (HD) ground wheeled vehicles. The SAE J2728 series of documents consists of the following:
The methodology for maximum package size loading is based on a mathematical method allowing the calculation of maximum package size tables. This method does not in principal differentiate between bulk loading and cargo system loading. However, some restrictions have to be considered: Some cargo systems generate pre-determined pallet trajectories. Envelope curves depending on the pallet size and the possible trajectories have to be determined first. Door geometric limitations (with or without cargo loading system) Turning limitations due to weight, load geometry and conveyance capability Securing requirements This document is not intended for airline operational use. It should be used by engineers performing calculations or developing computer programs to produce Maximum Package Size tables specified in AS1825.
This Glossary is designed to serve persons who need to know the accepted meanings, within specific contexts, of the terminology used in reports, articles, regulations, and other materials dealing with aviation safety -- with particular reference to terms specific to human factors in aviation safety. It is assumed that some users of the Glossary will be familiar with the nomenclature of aviation, but will need information on the language of human factors in engineering as they apply to aviation safety. Others (for example, engineers and psychologists) will have fairly extensive knowledge of the terminology of their own and related disciplines, but will need authoritative definitions of technical terms specific to aviation. Within the foregoing general framework, the following guidelines for the inclusion of terms to be defined have been observed:
This SAE Recommended Practice applies to speedometers, odometers, and speedometer drives typical of passenger vehicles, buses, and trucks used for personal or commercial purposes. The method of determining wheel revolutions per unit distance (3.1) and overall system design variation (3.3.3) are applicable to passenger cars only. Comparable recommendations for trucks and buses are under development. The data of tachometers is applicable to vehicular use, as previously described, and also to stationary and marine engines and special vehicles.
This SAE Standard defines a method for evaluating the immunity of automotive electrical/electronic devices to radiated electromagnetic fields coupled to the vehicle wiring harness. The method, called bulk current injection (BCI), uses a current probe to inject RF onto the wiring harness in the frequency range of 1 to 400 MHz. BCI is one of a number of test methods that can be used to simulate the electromagnetic field. The test method refers to ISO 11452-4 (please refer to ISO 11452-4 for test procedures). In addition to ISO 11452-4, this test method also includes a differential bulk current injection (DBCI) test. DBCI is described in Section 4 of this document.
Items per page:
50
1 – 50 of 221567