Results
This test method provides a procedure for measuring no-load rotational breakaway torque of self-lubricating spherical bearings.
This SAE Information Report establishes a uniform procedure for assuring the manufactured quality, installed utility, and performance of automotive remote steering controls other than those provided by the vehicle manufacturer (OEM). These products are intended to provide driving capability to persons with physical disabilities. The adaptive modifications seek to compensate for lost or reduced function in the extremities of the driver with a disability. Remote steering controls are designed to provide a steering input device alternative to the OEM steering wheel that either reduces the required input force, changes the required range of motion or changes the location of the steering control, or any combination of the above. These controls supplement by power, other than by the driver’s own muscular efforts, the force output of the driver with a disability. Because this is an Information Report, the numerical values for performance measurements presented in this report and in the
This SAE Aerospace Information Report (AIR) describes procedures for use in the field to determine if 115/200 Volt, 400 Hz aircraft external electrical power connectors are excessively worn, which may result in the inability of the external power plug to be retained, intermittent electrical performance, and arcing.
The primary objective of this recommended practice is to confirm that vehicles can communicate a minimum set of information in accordance with diagnostic test services specified in SAE J1979-2, or the equivalent ISO 14229-1:2013 (Ed. 2) and SAE J1979-3 documents. A successful result using the SAE J1699-5 Automotive Alliance for Innovation (AAI) software for OBD-II testing indicates that the main aspects of UDS communication have been examined, but it does not provide assurance of complete compliance with all aspects of SAE J1979-2 or SAE J1979-3. SAE J1699-5 tests run with a SAE J2534 device hardware and API that is not fully compliant will result in a test failure. This specification takes precedence over all conflicts in the documents cited in this section.
This SAE Information Report provides SAE’s recommendations for meeting the requirements for Real Emissions Assessment Logging (REAL) oxides of nitrogen (NOx) accuracy demonstration and for the implementation of REAL NOx binning requirements as defined in onboard diagnostics (OBD) regulations 13 CCR 1971.1 and 13 CCR 1968.2.
This specification covers a corrosion- and heat-resistant nickel alloy in the form of plate nominally 2.00 inches (50.8 mm) and under in thickness, inclusive.
This specification covers a corrosion- and heat-resistant cobalt alloy in the form of bars, forgings, flash-welded rings, and stock for forging or flash-welded rings.
This specification covers pure gold in the form of wire 0.005 to 0.040 inch (0.012 to 1.000 mm), inclusive, in nominal diameter and ribbon 0.002 to 0.051 inch (0.05 to 1.28 mm), inclusive, in nominal thickness (see 8.5).
This specification, in conjunction with the general requirements for steel heat treatment covered in AMS2759, establishes the requirements for heat treatment of precipitation-hardening corrosion-resistant, maraging, and secondary hardening steel parts. Parts are defined in AMS2759. Parts made from steels other than those specified in this specification may be heat treated in accordance with the applicable requirements herein using processing temperatures, times, and other parameters recommended by the material producer unless otherwise specified by the cognizant engineering organization. General ordering instructions are specified in AMS2759.
This specification covers a corrosion- and heat-resistant nickel alloy in the form of sheet, strip, and plate.
This SAE Recommended Practice was developed primarily for gasoline-powered passenger car and truck applications to interface vapor recovery systems, but it may be used in diesel, marine, industrial, and similar applications where a nozzle is required for filling. The zones cover nozzle spout access and handle clearance to a refilling port. In addition, this recommended practice includes a design window for nozzle manufacturers to develop with.
This specification covers a corrosion-resistant steel in the form of sheet, strip, and plate.
This specification covers a corrosion- and heat-resistant nickel alloy in the form of seamless tubing.
This specification covers a corrosion-resistant steel in the form of investment castings.
Restricted hardenability steels have been in use for some time but the specific restrictions for a particular grade depend upon customer needs and vary from mill to mill. Such steels are desirable to provide more controlled heat treatment response and dimensional control for critical parts. Because of increasing interest in steels with restricted hardenability, the SAE Iron and Steel Technical Committee directed Division 8 to prepare a set of standard steels with restricted hardenability. In 1993, the American Society for Testing and Materials (ASTM) adopted the twelve SAE restricted hardenability steels and added ten more. SAE decided to include in SAE J1868 the additional 10 steels. In general, steels with restricted hardenability (RH steels) will exhibit a hardness range not greater than 5 HRC at the initial position on the end-quench hardenability bar and not greater than 65% of the hardness range for standard H-band steels (see SAE J1268) in the "inflection" region. Generally the
This SAE Aerospace Information Report (AIR) discusses the nature of landing gear stability, describes many common landing gear stability problems, and suggests approaches and methods for solving or avoiding them.
This User Guide describes the content of the Rhapsody version of the UCS Architectural Model and how to use this model within the Rhapsody modeling tool environment. The purpose of the Rhapsody version of the UCS Architectural Interface Control Document (ICD) model is to provide a model for Rhapsody users, derived from the Enterprise Architect (EA) model (AIR6515). The AIR6515 EA Model, and by derivation, the AIR6517 Rhapsody Model, have been validated to contain the same content as the AS6518 model for: all UCS ICD interfaces all UCS ICD messages all UCS ICD data directly or indirectly referenced by ICD messages and interfaces the Domain Participant, Information, Service and Non-Functional Properties Models
This specification establishes general requirements for the processes listed in 3.8.1 for heat treatment of steel parts (see 8.2.1) by users or their vendors or subcontractors.
This specification covers the engineering requirements for heat treatment of magnesium alloy castings and for parts machined from castings.
This SAE Aerospace Information Report (AIR) provides details of how to perform hydraulic system calculations using equations that incorporate the metric International System of Units (SI).
This Aerospace Information Report (AIR) has been written to provide in-service reliability data of continuously active ball screw and geared flight control actuation systems.
This SAE Aerospace Information Report (AIR) describes the current process for performing comparative wear testing on aircraft tires in a laboratory environment. This technique is applicable to both radial and bias tires, and is pertinent for all aircraft tire sizes. This AIR describes a technique based upon “wear” energy. In this technique, side wear energy and drag wear energy are computed as the tire is run through a prescribed test program. The specifics that drive the test setup conditions are discussed in Sections 4 through 7. In general, the technique follows this process: A test profile is developed from measured mechanical property data of the tires under study. Each tire is repeatedly run to the test profile until it is worn to the maximum wear limit (MWL). Several tires, typically 5 to 10, of each tire design are tested. Wear energy is computed for each test cycle and then summed to determine total absorbed wear energy. An index is calculated for each tire design. This is
This SAE Recommended Practice provides test performance requirements for air disc brake actuators for service and combination service parking brake actuators with respect to function, durability, and environmental performance when tested according to SAE J2902.
This specification covers a premium aircraft-quality alloy steel in the form of welding wire.
This specification covers a special aircraft-quality, low-alloy steel in the form of bars, forgings, mechanical tubing, and forging stock.
This SAE Information Report establishes a consistent procedure for measuring and analyzing the natural sway response of a particular trailer when attached to a particular vehicle under specific loading and operating conditions. This test procedure applies, but is not limited to, passenger cars, vans, light/medium-duty trucks as tow vehicles, and semitrailers with a Gross Vehicle Weight Rating (GVWR) of 11794 kg (26000 pounds) or less. Other applications include full trailers, tow dollies, tow bars, and the like. Other articulated vehicles can utilize this test procedure as long as the test does not exceed the linear behavior of the system. This test procedure does not apply to motorcycles towing trailers.
This SAE Information Report should be used as a supplement to SAE J1383 (Reference 2.1.1). It is intended to provide additional information which is important to the automotive designer and engineer in the process of designing, developing, and engineering the headlamps of motor vehicles which will take into account the effects of the aging process on the driver.
This SAE Aerospace Standard (AS) establishes the requirements for fluid fittings that combine both 37 degree flared and pipe threaded connections for use in all types of fluid systems.
Items per page:
50
1 – 50 of 222741