Results
This SAE Standard establishes the test procedure, environment, and instrumentation for determining the sound levels of snowmobiles in the stationary test mode. This test method is intended to provide an accurate measurement of exhaust and other engine noise and may be used to evaluate new and in-use snowmobiles to determine compliance with noise control regulations. Sound level measurements obtained with this test method are not intended as an engineering determination of overall machine noise. For this purpose, the use of SAE J192 is recommended.
This SAE Standard covers general, dimensional data, and methods of test for two types of general purpose nut and conical spring washer assemblies, designated Type LN and Type HN, intended for mass production and other operations where speed and convenience are paramount factors.
This SAE Aerospace Standard (AS) covers ULDs utilized in finding submerged aircraft. Such ULDs are installed within the aircraft in a manner that they are unlikely to become separated during crash conditions. The low frequency ULD should be attached to the airframe in accordance with the manufacturer’s recommendations in order to maximize the underwater detection range. ARINC Standard 677 also provides installation guidance for Low Frequency ULDs.
This SAE Aerospace Information Report presents a glossary of terms commonly used in the ground delivery of fuel to an aircraft and pertinent terms relating to the aircraft being refueled.
This SAE Aerospace Recommended Practice (ARP) establishes the guidelines for selection of titles of aerospace fitting documents generated by SAE Subcommittee G-3B.
This specification covers a corrosion and heat resistant steel in the form of welding wire.
The objective of this ARP is to provide a set of user-centered design guidelines for the implementation of data driven electronic aeronautical charts, which dynamically create charts from a database of individual elements. The data driven chart is intended to provide information required to navigate, but it is not intended to supplant the aircraft’s primary navigation display. These guidelines seek to provide a balance between standardization of equipment with similar intended functions and individual manufacturer innovation. This ARP provides guidelines for the display of an electronic chart that can replace existing paper. This document addresses what information is required, when it is required, and how it should be displayed and controlled. This document does not include all the detailed specifications required to generate an electronic aeronautical chart. This document primarily addresses the human factors aspects of electronic chart display, and does not address the software
This specification covers a premium aircraft-quality, maraging steel in the form of sheet, strip, and plate.
This SAE Aerospace Recommended Practice (ARP) covers specification requirements for a rotary plow with carrier vehicle. The primary use is to cast heavy concentrations of snow approximately perpendicular to carrier vehicles across and away from airport operational areas, such as runways and taxiways. Rotary plows equipped with spot casting, or loading chutes are also used to cast snow in directions through approximately 100 degrees to the left or right of directly in front of the carrier vehicle, and also to load trucks or trailers used to haul snow away from removal area. The term “carrier vehicle” represents the various self-propelled prime movers that provide the power necessary to move snow and ice control equipment during winter operations.
This SAE Standard was developed to provide a method for indicating the direction of engine rotation and numbering of engine cylinders. The document is intended for use in designing new engines to eliminate the differences which presently exist in industry.
This document defines the requirements for weld fittings and machine weldments using an orbiting welding head suitable for use on cold worked 3AL-2.5V titanium, 21Cr-6Ni-9Mn CRES, and 718 nickel alloy tubing. Fitting standards covered by this specification include non-separable welded elbow, tee, and reducer fittings, and reconnectable 24-degree cone fittings, such as sleeves and unions.
This SAE Standard covers the mechanical and material requirements for eight property classes of steel, externally threaded metric fasteners in sizes M1.6 through M36, inclusive, and suitable for use in automotive and related applications.
This SAE Aerospace Standard (AS) establishes the requirements for AS3504 and AS3505 thin wall self-locking inserts made from a corrosion and heat resistant, age hardenable nickel base alloy of the type identified under the Unified Numbering System as UNS N07718.
The technical architecture defined in this document outlines mandatory, emerging, and needed standards to provide interoperability at key interfaces in the aircraft/store system (including an associated NATO Network Enabled Capability environment), as required to support a future plug-and-play aircraft/store integration capability. These standards relate to services and protocols associated with the subject interfaces. Modeling standards to facilitate the Model Driven Architecture® (MDA®) approach to system definition and implementation are also included. Note that the status of referenced standards as reflected in this document is as of August 2007, and document users should check to see if there has been a subsequent change of status relative to applicable standards.
This specification covers an irradiated, thermally-stabilized, modified polyolefin plastic in the form of thin-wall tubing.
This specification covers acrylic-monomer base adhesives intended for use in bonding acrylic plastics.
This specification covers a phenol/formaldehyde-resin-impregnated, cotton fabric laminate in the form of sheet.
This specification covers a two-component silicone rubber sealant and compatible primers.
This specification presents requirements for the heat treatment of parts and components fabricated from wrought (plate, sheet, strip, bar, rod, wire extrusions and tube and forgings) copper alloys, numbers C17000, C17200, C17300, C17500, and C17510 (see 6.7). This specification also covers “bright hardening”.
This specification covers a polytetrafluoroethylene (PTFE) modified fluorosilicone (FVMQ) rubber in the form of molded shapes, molded rings (ASTM D 1414), and compression seals.
This specification covers a corrosion and heat-resistant steel in the form of welding wire.
This specification covers the engineering requirements and process for brush plating of tin by electrodeposition. It shall be used, in conjunction with AMS2451, for general purpose tin deposits.
This specification covers the requirements for six alloy compositions, four inspection classes, four radiographic quality grades and six classes of mechanical properties of high strength aluminum-alloy castings.
Wire and cable products progress through a series of handling or operational steps from the time they leave the manufacturer, and until a finished harness or assembly is ready for installation on a vehicle. Throughout these many steps, environmental or processing conditions may be present which can generate damage detrimental to the wire or cable and/or its intended application.
This document presents minimum criteria for the design and installation of LED passenger reading light assemblies in commercial aircraft. The use of “shall” in this specification expresses provisions that are binding. Non-mandatory provisions use the term “should.”
This procurement specification covers aircraft-quality solid rivets made from a corrosion resistant nickel-copper alloy of the type identified under the Unified Numbering System as UNS N04400 and of 46 ksi minimum shear strength.
This AS defines instruments which use inputs of static and pitot pressure equal to those which are utilized to establish the pressure altitude and speed of that aircraft. These pressures are applied to the instrument ports to provide means for generation of an aural warning whenever the aircraft reaches or exceeds the maximum operating limit speed. This Over Speed Warning Instrument function may be incorporated as part of an Air Data Computer, or an Air Speed Indicator, or an Air Speed/Mach Number Indicator, or other instruments. In those cases where the Over Speed Warning Instrument is part of another instrument, the standards contained herein apply only to the Over Speed Warning Instrument function. Each aircraft type and model has a defined maximum operating limit speed curve or curves which are a part of the airframe manufacturer's type certification approval data; this limit speed data shall be available from the subject airframe manufacturer as published in the operating manual
Items per page:
50
1 – 50 of 220040