Results
This method is intended to evaluate the thermal and oxidative stability of synthetic, ester-based aviation lubricants under defined conditions of time and temperature. This method is applicable to lubricants meeting the compositional and performance requirements of AS5780.
Long wave ultraviolet or UV-A irradiation (between 320 and 400 nm) is used for fluorescent inspections in magnetic particle and liquid penetrant examinations. UV-A irradiation is obtained from either LED, fluorescent, or high intensity discharge lamps that are stationary or portable. Commercially available UV-A lamps possess a large variation in intensity output that may introduce a legitimate concern for possible health hazards. This document reviews the nature of UV-A irradiation emitted by lamps and acceptable UV dosage limits adopted by the American Conference of Governmental Industrial Hygienists (ACGIH®) and European Union and recommendation of proper practices when working with UV-A irradiation.
This specification covers the installation of aircraft interior lighting for military aircraft.
This specification covers an aluminum alloy in the form of plate.
This Aerospace Recommended Practice (ARP) outlines the causes and impacts of moisture and/or condensation in avionics equipment and provides recommendations for corrective and preventative action.
The air cranking system components, which include the tank, valve, hose, and starter, must be carefully selected to provide the necessary speed to start an engine under the most severe climatic conditions for which the system is intended. Engine cranking loads increase with cold temperatures, therefore, the initial selection of these components, needs to consider low-temperature engine torque requirements. To insure an adequate air cranking system is obtained, it is important that proper test procedures are used for obtaining the cranking load requirements of the engine.
This specification covers quality assurance sampling and testing procedures used to determine conformance to applicable material specification requirements of wrought carbon and low-alloy steel products and of forging stock.
This code is intended for commercial vehicles over 4500 kg (10 000 lb) with brake systems having typical service pressure ranges 0 to 14.1 mPa (0 to 2050 psi) hydraulic or 0 to 830 kPa (0 to 130 psi) air and is not directly applicable to vehicles with other systems. Air over hydraulic systems are to be tested as air systems.
This SAE Recommended Practice defines the test stand and procedure for evaluating radial impacts of all wheels intended for passenger cars and light trucks. A minimum performance requirement is intentionally not provided. The intent is to establish a uniform method and test stand for imparting damage and evaluating radial impacts. A minimum performance requirement will be a proposed change when users determine what is of most value.
This standard is for use by organizations that procure and integrate EEE Parts. These organizations may provide EEE Parts that are not integrated into assemblies (e.g., spares and/or repair EEE Parts). Examples of such organizations include, but are not limited to, the following: Original Equipment Manufacturers; contract assembly manufacturers; maintenance, repair, and overhaul (MRO) organizations; and suppliers that provide EEE Parts or assemblies as part of a service. These requirements are intended to be applied (or flowed down as applicable) through the supply chain to all organizations that procure and integrate EEE Parts and/or systems, subsystems, or assemblies. The mitigation of Counterfeit EEE Parts in this standard is risk based. These mitigation steps will vary depending on the criticality of the application and desired performance and reliability of the equipment/hardware. The requirements of this document are used in conjunction with the organization’s higher-level
This SAE Standard was developed to provide a method for indicating the direction of engine rotation and numbering of engine cylinders. The document is intended for use in designing new engines to eliminate the differences which presently exist in industry.
The requirements of 9100 apply with the following clarification for software. This standard supplements the 9100 standard requirements for deliverable software and contains quality management system requirements for organizations that design, develop, and/or produce deliverable software and services for the aviation, space, and defense industry. This includes, as required, support software that is used in the development and maintenance of deliverable software and services. The deliverable software may be stand-alone, embedded, mobile application, or loadable into a target computer. This deliverable software may also be part of services (e.g., cloud environment, web hosted solutions or platforms). Where the use of Hardware Description Language (HDL) or high order language is utilized as the design source of electronic hardware [e.g., Application Specific Integrated Circuit (ASIC), Programmable Logic Device (PLD)]; the organization and customer, and/or supplier shall agree on the extent
This SAE Aerospace Standard (AS) establishes supplemental requirements for 9100 and 9145 and applies to any organization receiving it as part of a purchase order or other contractual document from a customer. AS13100 also provides details of the reference materials (RM13xxx) developed by the SAE G-22 AESQ committee and listed in Section 2 that can also be used by organizations in conjunction with this standard.
This document applies to safety observers or spotters involved with the use of outdoor laser systems. It may be used in conjunction with AS4970.
This SAE Standard covers general, dimensional data, and methods of test for two types of general purpose nut and conical spring washer assemblies, designated Type LN and Type HN, intended for mass production and other operations where speed and convenience are paramount factors.
This SAE Aerospace Recommended Practice (ARP) is written for individuals associated with the ground-level testing of large and small gas turbine engines and particularly for those who might be interested in constructing new or adding to existing engine test cell facilities.
Items per page:
50
1 – 50 of 222094