Results
This SAE Standard establishes the test procedure, environment, and instrumentation for determining the sound levels of snowmobiles in the stationary test mode. This test method is intended to provide an accurate measurement of exhaust and other engine noise and may be used to evaluate new and in-use snowmobiles to determine compliance with noise control regulations. Sound level measurements obtained with this test method are not intended as an engineering determination of overall machine noise. For this purpose, the use of SAE J192 is recommended.
This SAE Aerospace Information Report (AIR) has been written for individuals associated with the ground-level testing of large and small gas turbine engines and particularly for those who might be interested in upgrading their existing or acquiring new test cell facilities.
SAE J2534-1_0500 defines the pass-thru interface requirements for the reprogramming of emission related control modules. The SAE J2534-2/X_0500 document set adds extensions to the SAE J2534-1_0500 API (version 05.00) specification so that the API can be used for features not covered in the SAE J2534-1_0500 specification. Together, these features provide a comprehensive framework for a common standard, to protect the software investment of the vehicle OEMs and scan tool manufacturers. There is no required for an SAE J2534-2/X_0500 pass-thru interface to be fully compliant with SAE J2534-1_0500. SAE J2534-2/X_0500 interfaces can implement some or all of the features specified in the SAE J2534-2/X_0500 document set. This document must be used in conjunction with the SAE J2534-2/RE_0500 document.
This standard defines the requirements for bulk protective sleeve to provide fire resistance for aircraft hose assemblies, which will enable these assemblies to meet the requirements of AS1055. NOTE: Use of this sleeve does not eliminate the need to demonstrate that the sleeved assemblies will meet the applicable requirements of AS1055.
This document contains procedures for performance testing of electrical terminals, connectors, and components for coaxial-style cable with an outside cable diameter of 3.6 mm and smaller. These are often called “mini coax connector systems.” This specification applies to coaxial cable connection systems that operate at frequencies from DC to 9 GHz and are intended for road vehicles. The characteristic impedance of the mini coax connection system described here is 50 Ω, however nothing excludes the use of these connectors in systems with a different characteristic impedance. This specification applies only to connection systems using coaxial cable.
This document is intended for use by manufacturers of aircraft, engines and Electronic Engine Controls [EECs] as a component change process and evaluation guideline. Its purpose is to provide an effective means of managing the modification of electronic hardware. The process defined in this document is based upon: an understanding of the electronic component market evolution, e.g., obsolescence; lessons learned from the effects caused by the introduction of electrical component changes in a service fleet environment; industry best practice; and an understanding of the applicable regulations.
This SAE Aerospace Standard (AS) defines the requirements for air cycle air conditioning systems used on military air vehicles for cooling, heating, ventilation, and moisture and contamination control. General recommendations for an air conditioning system, which may include an air cycle system as a cooling source, are included in MIL-E-18927E and JSSG-2009. Air cycle air conditioning systems include those components which condition high temperature and high pressure air for delivery to occupied and equipment compartments and to electrical and electronic equipment. This document is applicable to open and closed loop air cycle systems. Definitions are contained in Section 5 of this document.
This specification covers a chloroprene (CR) rubber in the form of sheet, strip, tubing, extrusions, and molded shapes.
This SAE Recommended Practice provides a uniform procedure and performance requirements for evaluating fastening systems for normal highway use on aftermarket passenger cars and light trucks (except dual wheels, which are covered by SAE J1965) and multipurpose passenger vehicles. The fastening system includes the wheel, wheel bolts, and wheel nuts, as well as vehicle mating surface. The coefficients of friction for steel and aluminum mating surfaces are provided based on information available. Many factors must be considered in design and validation of wheel attachments for each specific vehicle. Where the procedure is used for original equipment applications the vehicle manufacturers specifications supersede those noted.
This specification covers balls made of a low-chromium, high-carbon steel.
Scope is unavailable.
This recommended practice provides the design criteria for static elastomeric O-ring seals used specifically in engine and engine control systems. It provides axial compression (face type) groove dimensions for aerospace metric O-ring sizes specified in MA2010. The conditions considered to formulate the design criteria are also described, e.g., seal squeeze and groove volume to accommodate O-ring swell. NOTE: Tables of O-ring groove dimensions are included based on the design criteria specified herein. Dimensions in this document are in millimeters unless otherwise specified.
This specification covers several grades of virgin polytetrafluoroethylene (PTFE) resin which may be compounded with pigment and fillers in the form of extruded or molded rods or tubes which are sintered after molding or, in the case of extrusions, sintered during the extrusion process.
This specification covers aluminum alloy die castings.
This SAE Aerospace Recommended Practice (ARP) specifies for quality requirements that are additive to a procurement document or contract, where an organization: a needs to provide additional guidance for suppliers and other organizations in the delivery of products, goods and services in accordance with stated quality demands, and b needs to provide information in addition or in absence of existing quality system requirements to provide the assurance of conformity to customer and applicable regulatory requirements. NOTE: In this ARP, the term ‘product’ applies only to the product intended for, or required by, a customer.
This specification covers expanded honeycomb core made of glass cloth impregnated with polyimide resin and supplied in the form of blocks, slices, and ordered shapes.
MIL-STD-1553 establishes requirements for digital command/response time division multiplexing (TDM) techniques on military vehicles, especially aircraft. The existing MIL-STD-1553 network operates at a bit rate of 1 Mbps and is limited by the protocol to a maximum data payload capacity of approximately 700 kilobits per second. The limited capacity of MIL-STD-1553 buses coupled with emerging data rich applications for avionics platforms plus the expense involved with changing or adding wires to thousands of aircraft in the fleet has driven the need for expanding the data carrying capacity of the existing MIL-STD-1553 infrastructure.
This SAE Standard covers the mechanical and physical requirements for Compacted Graphite Iron (CGI) castings used in automotive and allied industries. Requirements in this document include: a Tensile Strength b Yield Strength c Elongation d Graphite Morphology
This SAE Standard covers the mechanical and material requirements for three grades of steel nuts suitable for use in automotive and related engineering applications, in sizes 1/4 to 1-1/2 inches, inclusive, and with dimensions conforming with the requirements of the latest issue of SAE J482 or ASME B18.2.2, except for machine screw nuts which are not covered in this standard. This document does not include limits for surface discontinuities. Where usage requires such control, limits may be specified separately. For sizes 1/4 through 1 inch, this may be done by the statement: “Surface discontinuities shall not exceed the limits specified in ASTM F812/F812M.”
This Aerospace Standard (AS) defines the requirements for polytetrafluoroethylene (PTFE) heavy duty hose assemblies suitable for use in aircraft and missile hydraulic fluid systems service to 8000 psi and -65 to 400 °F. Gaseous service shall be limited to 150 °F.
This specification covers the specific requirements for 2014 aluminum alloy alclad plate and sheet; the general requirements are covered in AMS-QQ-A-250. The plate and sheet covered by this specification shall be an integral composite product consisting of a heat-treatable aluminum alloy (2014) core with thin layers of an aluminum alloy (6003) anodic to the core and of approximately equal thickness bonded to both surfaces.
This SAE Aerospace Recommended Practice (ARP) is a guide for defining the requirements for aerospace piston hydraulic accumulators, including details pertinent to the design, fabrication, performance and testing of the accumulator. This type of accumulator contains a piston which separates pressurized gas and fluid.
This standard covers self-propelled off-road work machines as categorized in SAE J1116 and Agricultural Tractors as defined in ANSI/ASAE S390.
This SAE Aerospace Information Report (AIR) applies to landing gear tires and airframe structure for all types and models of civil and military aircraft having tires as part of the landing gear.
This specification covers the specific requirements for 5454 aluminum alloy plate and sheet; the general requirements are covered in AMS-QQ-A-250.
This document defines the process steps involved in collecting and processing engine test data for use in understanding engine behavior. It describes the use of an aero-thermal cycle model for reduction and analysis of those data. The analysis process may include the calculation of modifiers to match the model to measured data and prediction of engine performance based on that analysis.
This specification has previously been widely used and may be required for production or processing of existing designs in the future. The Aerospace Materials Division, however, does not recommend this specification for future use in new designs (See 6.7).
Consideration for the damaging effects to aircraft from the failure of wheels and tires should be evaluated. This document discusses the types of problems in-service aircraft have experienced and methodology in place to assist the designers when evaluating threats for new aircraft design. The purpose of this document is to provide a history of in-service problems, provide a historical summary of the design improvements made to wheels and tires during the past 40 years, and to offer methodology which has been used to help designers assess the threat to ensure the functionality of systems and equipment located in and around the landing gear and in wheel wells.
Items per page:
50
1 – 50 of 220040