Results
This AIR provides information about the specific requirements for missile hydraulic pumps and their associated power sources.
This SAE Aerospace Standard establishes the requirements for a V-retainer coupling, flanges, and seal suitable for joining high-pressure and high-temperature ducting in aircraft bleed air systems. The rigid coupling joint assembly, hereafter referred to as “the joint,” shall operate within the temperature range of -65 to +1200 °F.
SCOPE IS UNAVAILABLE.
This specification covers a copper alloy (phosphor bronze) in the form of sheet, strip, and plate (see 8.6).
This specification covers an aluminum alloy in the form of plate 0.500 to 4.500 inches (12.7 to 114.3 mm), inclusive, in nominal thickness (see 8.5).
This SAE Aerospace Recommended Practice (ARP) provides information and guidance for the control of hazardous laser exposure in the navigable airspace. This ARP does not address techniques that pilots can apply to mitigate laser illuminations during a critical phase of flight. Such mitigation strategies are described in ARP6378.
SCOPE IS UNAVAILABLE
This specification covers a corrosion-resistant nickel-copper alloy in the form of seamless tubing.
This document applies to laser proponents involved with the use of laser systems outdoors. It may be used in conjunction with AS4970, ARP5535, ARP5572, and the ANSI Z136 series of laser safety standards.
This specification, in conjunction with the general requirements for steel heat treatment covered in AMS2759, establishes the requirements and procedures for three classes of gas, vacuum, liquid, and low-pressure carburizing (LPC) and related heat treatment of parts fabricated from carburizing-grade steels. Parts made from steels other than those specified in the detail specifications may be heat treated in accordance with the applicable requirements using processing temperatures, times, and other parameters recommended by the material producer. This specification does not cover pack carburizing.
This specification covers an aluminum alloy in the form of castings (see 8.10).
This specification covers a premium aircraft-quality, low-alloy steel in the form of bars, forgings, and mechanical tubing 225 square inches (1452 cm2) and under in cross-sectional area and forging stock of any size.
This SAE Aerospace Recommended Practice (ARP) describes a method for evaluating the performance of filter elements designed for aerospace hydraulic systems. The performance is measured and reported in terms of filtration ratios and stabilized contamination levels while testing with cyclic flow.
This document applies to regulatory/approving authorities involved with decisions regarding the use of high-intensity light (HIL) directed into the navigable airspace. For the purpose of this document, lights greater than 0.25 million candlepower meet the minimum threshold of an HIL. Lights not directed or reflected into the navigable airspace are not usually considered to interfere with aircraft operations. HILs include laser-derived light sources; other laser systems are beyond the scope of this document. This document addresses adverse effects of HILs on humans, such as visual interference. HIL effects on Unmanned Aircraft Systems (UASs) are beyond the scope of this document.
SCOPE IS UNAVAILABLE.
This specification defines limits of variation for determining acceptability of composition of cast and wrought corrosion and heat-resistant steels and alloys, maraging and other highly alloyed steels, and iron alloy parts and materials acquired from a producer.
This document provides guidance concerning the maintenance and serviceability of oxygen cylinders beginning with the quality of oxygen that is required, supplemental oxygen information, handling and cleaning procedures, transfilling, and marking of serviced oxygen assemblies. This document attempts to outline in a logical sequence oxygen quality, serviceability, and maintenance of oxygen cylinders. Content of this document can also be used for refilling oxygen cylinders while installed on aircraft, directly or through an intermediate charging port.
SCOPE IS UNAVAILABLE.
This SAE Aerospace Recommended Practice (ARP) is intended to be used for laser systems mounted on aircraft and propagated into navigable airspace. This does not include lasers onboard aircraft where the beam is contained within an enclosure so that the beam cannot enter into airspace, nor does it include lasers from satellites and spacecraft in outer space. It may be used in conjunction with AS4970, ARP5535, ARP5572, ARP5293, and the ANSI Z136 laser safety standards.
This document and the EUROCAE equivalent, ED-107, provides detailed information, guidance, and methods in support of the Federal Aviation Administration (FAA) Advisory Circular (AC) 20-158 and to the European Union Aviation Safety Agency (EASA) AMC 20-158. AC 20-158 provides a means, but not the only means, for demonstrating compliance with Title 14 of the Code of Federal Regulations (14 CFR) 23.1308 (Amendment 57 and lower), 23.2520 (Amendment 64 and higher), 25.1317, 27.1317, 29.1317, and applicable FAA HIRF special conditions addressing HIRF Protection. AMC 20-158 is applicable to Certification Specifications CS 23.1308 (Amendment 4 and lower), 23.2520 (Amendment 5 and higher), 25.1317, 27.1317, and 29.1317. It should be noted that this document is neither mandatory nor regulatory in nature and does not constitute a regulation or legal interpretation of the regulation. Therefore, an applicant may elect to establish an alternative method of compliance that is acceptable to the
This SAE Recommended Practice provides a taxonomy of terms related to local and regional on-demand and shared mobility services (including ground, aviation, and maritime) and their enabling technologies. Functional definitions for shared modes (both fleet sharing and ride services), services, business models, and mobility applications are defined in this SAE Recommended Practice. This SAE Recommended Practice also provides a taxonomy of related terms and definitions. Though public transport is part of shared mobility, it is not included in this SAE Recommended Practice because its definition is well-established and documented. This document does not provide specifications or otherwise impose requirements on on-demand and shared mobility.
This specification covers the requirements for electrodeposited gold plate.
This specification covers columbium in the form of sheet, strip, plate, and foil.
This specification covers a corrosion- and heat-resistant nickel alloy in the form of sheet, strip, and foil 0.100 inch (2.54 mm) and under in nominal thickness.
This SAE Recommended Practice provides recommended guidelines and best practices for implementing a supportability program to ensure that software is supportable throughout its life cycle. This Implementation Guide is the companion to the Software Supportability Program Standard, SAE JA1004, that describes, within a Plan-Case framework, what software supportability performance requirements are necessary. This document has general applicability to all sectors of industry and commerce and to all types of equipment whose functionality is to some degree implemented via software. It is intended to be guidance for business purposes and should be applied when it provides a value-added basis for the business aspects of development, use, and sustainment of support-critical software. Applicability of specific recommended practices will depend on the support-significance of the software, application domain, and life cycle stage of the software.
Items per page:
50
1 – 50 of 219637