Results
Long wave ultraviolet or UV-A irradiation (between 320 and 400 nm) is used for fluorescent inspections in magnetic particle and liquid penetrant examinations. UV-A irradiation is obtained from either LED, fluorescent, or high intensity discharge lamps that are stationary or portable. Commercially available UV-A lamps possess a large variation in intensity output that may introduce a legitimate concern for possible health hazards. This document reviews the nature of UV-A irradiation emitted by lamps and acceptable UV dosage limits adopted by the American Conference of Governmental Industrial Hygienists (ACGIH®) and European Union and recommendation of proper practices when working with UV-A irradiation.
This method is intended to evaluate the thermal and oxidative stability of synthetic, ester-based aviation lubricants under defined conditions of time and temperature. This method is applicable to lubricants meeting the compositional and performance requirements of AS5780.
This specification covers the installation of aircraft interior lighting for military aircraft.
This document provides recommendations to identify battery group sizes and dimensions for 6 V, 8 V, 12 V, and 24 V lead acid batteries.
This specification establishes the procedures used to produce a hard anodic coating on magnesium alloys and the properties of the coating.
This specification covers a corrosion-resistant steel in the form of sheet, strip, and plate.
This specification covers a manganese alloy in the form of powder, preforms, and a viscous mixture (paste) of the powder in a suitable binder.
This specification is a general level subsystem light source specification that establishes test requirements of light emitting diode (LED) components and modules for use in automotive lighting systems. The completed test data from this test specification is intended to be provided to the OEM by the Tier 1 lamp set maker as part of the lamp assembly PPAP. Re-testing shall be required if any portion of the approved LED module experiences a design, manufacturing, or component change. This document shall be applied to systems that meet the requirements for design, performance, and validation established by government standards. The LED module is defined as the LED devices and any electronics required to properly energize the LEDs using a vehicle electrical power system along with any associated electrical wiring, connectors, and thermal management system. Samples shall be tested as a subsystem and considered one test sample for the entire test sequence. A failure of any component in the
This SAE Recommended Practice provides the framework to allow reprogramming software applications from all vehicle manufacturers the flexibility to work with multiple vehicle data link interface tools from multiple tool suppliers. This system enables each vehicle manufacturer to control the programming sequence for electronic control units (ECU’s) in their vehicles, but allows a single set of programming hardware and vehicle interface to be used to program modules for all vehicle manufacturers. This document does not limit the hardware possibilities for the connection between the PC used for the software application and the tool (e.g., RS-232, RS-485, USB, Ethernet…). Tool suppliers are free to choose the hardware interface appropriate for their tool. The goal of this document is to ensure that reprogramming software from any vehicle manufacturer is compatible with hardware supplied by any tool manufacturer. The U.S. Environmental Protection Agency (EPA) and the California Air
This document defines the minimum requirements for auditors, CBs, Auditor Authentication Bodies (AABs), Training Provider Approval Bodies (TPABs), and Training Providers (TPs) who participate in the IAQG Industry Controlled Other Party (ICOP) scheme. The requirements in this standard supplement those defined within the 9104/1, 9104/2, ISO/IEC 17021-1, and ISO/IEC 17021-3 standards. Data protection for the parties subject to this document and other relevant requirements of the ICOP scheme are managed via bi-lateral contracts between the joint controllers of the data.
Groove designs presented herein are applicable for use with the following "MS" metal O-ring gaskets conforming to the applicable "AS" standard drawings listed in 1(a) or 1(b), or to dimensionally equivalent gaskets of other materials: a AMS 5570 or AMS 5576 Plain 1 AS9141 - 0.035 tube × 0.006 wall 2 AS9142 - 0.062 tube × 0.006 wall 3 AS9202 - 0.062 tube × 0.010 wall 4 AS9203 - 0.094 tube × 0.006 wall 5 AS9204 - 0.094 tube × 0.010 wall 6 AS9205 - 0.125 tube × 0.010 wall b AMS 5570 or AMS 5576 Silver Plated 1 AS9371 - 0.035 tube × 0.006 wall 2 AS9372 - 0.062 tube × 0.006 wall 3 AS9373 - 0.062 tube × 0.010 wall 4 AS9374 - 0.094 tube × 0.006 wall 5 AS9375 - 0.094 tube × 0.010 wall 6 AS9376 - 0.125 tube × 0.010 wall NOTE: The term "AS gasket" as used in this document refers to the 'MS' part numbers defined on the applicable 'AS' standards listed in 1(a) or 1(b).
This specification covers an aircraft-quality, low-alloy steel in the form of bars, forgings, mechanical tubing, and forging stock.
This specification covers coated round rods manufactured by the pultrusion process from glass fiber roving and a weather-resistant polyester resin binder in the form of straight lengths or in coils.
This specification covers coated round rods fabricated by the pultrusion process from aramid fibers and a weather-resistant polyester resin binder in the form of straight lengths or in coils.
The recommended practice describes a design standard that defines the maximum recommended voltage drop of the starting motor main circuits, as well as control system circuits, for 12/24-V starter systems. The battery technologies used in developing this document include the flooded lead acid, gel cell, and AGM. Starting systems supported by NiCd, Lithium Ion, NiZn, etc., or Ultracaps are not included in this document. This document is not intended to be updated or modified to include starter motors rated at voltages above the nominal 24-V electrical system. The starter is basically an electrical-to-mechanical power converter. If you double the available battery power in, you double the peak mechanical power out and double the heat losses. This means that we have to pay special attention to how battery power changes when we change the battery voltage and the effects it may have in overpowering the cranking system. A new stand-alone document would need to be developed to address
AMS6885/1 gives information about the technical requirements and qualification procedure for unidirectional carbon fiber tape epoxy repair prepreg capable of curing under vacuum for repair of carbon fiber reinforced epoxy structures. The repair system includes an epoxy film adhesive to be applied in a co-bonding process with the prepreg for solid laminate and sandwich bonding.
This SAE Information Report is the listing of recommendations for the proper packaging, storage, and shelf life limitations of new and unused hydraulic brake hose assemblies. The document embodies the testing, analysis, and experience of many users and manufacturers. Where specific manufacturer's recommendations are made, those recommendations shall supersede the recommendations of this document. This document describes the successful procedures and practices associated with brake hose assemblies usage by a wide cross section of manufacturers and users over several years. The practices are expected to be applicable to all brake hose assemblies which qualify under SAE J1401.
This AIR is limited to the requirements of AS50881 and examines these requirements, providing rationale behind them. AS50881 is only applicable to the aircraft EWIS. Pods and other devices that can be attached to an aircraft are considered as part of the aircraft equipment design. Its scope does not include wiring inside of airborne electronic equipment but does apply to wiring externally attached to such equipment. The AS50881 scope does not include attached devices but does include the interface between the pod/equipment and aircraft wiring. Section 3.3.5 addresses components such as antennas and other similar equipment that were once supplied as Government Furnished Aeronautical/Aerospace Equipment (GFAE).
These recommended practices provide recommendations for general specifications and performance requirements of carbon, alloy and high strength low alloy steel tube assemblies for fluid power applications utilizing commonly available manufacturing methods and general guidelines for tube selection and application.
This report identifies the reasons for, and results associated with, the conduct of a flight simulation research project evaluating the effect of low powered laser beam illumination of pilot crewmembers operating in the navigable airspace. This evaluation was primarily concerned with the possible degradation of pilot performance when illuminated by a laser while operating in an airport terminal area where pilot workloads are normally at their maximum.
Items per page:
50
1 – 50 of 222094