Results
This SAE Aerospace Information Report (AIR) discusses past and present approaches for monitoring the landing gear structure and shock absorber (servicing), opportunities for corrosion detection, methods for transient overload detection, techniques for measuring the forces seen by the landing gear structure, and methods for determining the fatigue state of the landing gear structure. Landing gear tire condition and tire pressure monitoring are detailed in ARP6225, AIR4830, and ARP6137, respectively. Aircraft Brake Temperature Monitoring Systems (BTMS) are detailed in AS1145.
This test method provides a procedure for measuring no-load rotational breakaway torque of self-lubricating spherical bearings.
This test plan consists of two major sections for testing of MIL-STD-1553B data bus systems: Bus Network and System Integration Tests.
This specification covers two grades of ethylene-propylene rubber having excellent resistance to ozone and hot water, but poor resistance to hydrocarbon oils or solvents.
The gear lubricants covered by this standard exceed American Petroleum Institute (API) Service Classification API GL-5 and are intended for automotive units with the primary drive hypoid gears, operating under conditions of high-speed/shock load and low-speed/high-torque. These lubricants may be appropriate for other gear applications where the position of the shafts relative to each other and the type of gear flank contact involve a large percentage of sliding contact. Such applications typically require extreme pressure (EP) additives to prevent the adhesion and subsequent tearing away of material from the loaded gear flanks. These lubricants are not appropriate for the lubrication of worm gears. The information contained within is intended for the demonstration of compliance with the requirements of this standard and for listing on the Qualified Products List (QPL) administered by the Lubricant Review Institute (LRI). A complete listing of qualification submission requirements and
This specification covers a tetrafluoroethylene/propylene rubber (FEPM) in the form of molded rings.
This SAE Standard is equivalent to ISO 362-1:2015 and specifies an engineering method for measuring the noise emitted by road vehicles of categories M and N under typical urban traffic conditions. It excludes vehicles of category L1, L2, L3, L4, and L5. The specifications are intended to reproduce the level of noise generated by the principal noise sources during normal driving in urban traffic. The method is designed to meet the requirements of simplicity as far as they are consistent with reproducibility of results under the operating conditions of the vehicle. The test method requires an acoustical environment that is obtained only in an extensive open space. Such conditions are usually provided for during: Measurements of vehicles for regulatory certification and/or type approval Measurements at the manufacturing stage Measurements at official testing stations Annex A provides background information on the use of this standard consistent with the intent.
This SAE Standard provides basic information on the International System of Units, abbreviated SI in all languages, and its application in engineering practice and measurement unit usage.
This specification covers a corrosion-resistant steel in the form of investment castings.
This specification covers a corrosion- and heat-resistant nickel alloy in the form of seamless tubing.
This Surface Vehicle & Aerospace Recommended Practice offers best practices and a methodology by which IVHM functionality relating to components and subsystems should be integrated into vehicle or platform level applications. The intent of the document is to provide practitioners with a structured methodology for specifying, characterizing and exposing the inherent IVHM functionality of a component or subsystem using a common functional reference model, i.e., through the exchange of design-time data and the application of standard vehicle data communications interfaces. This document includes best practices and guidance related to the specification of the information that must be exchanged between the functional layers in the IVHM system or between lower-level components/subsystems and the higher-level control system to enable health monitoring and tracking of system degradation severity. The intent is to provide an IVHM system that can robustly report the degradation of a given
This Information Report relates to a special class of automotive adaptive equipment which consists of modifications to the power brake booster systems provided as original equipment of motor vehicles. These modifications are generically called "Reduced Effort Power Brakes" (REPB) The purpose of the modification is to lower the amount of driver effort required to apply the brakes. Retention of reliability, ease of use and maintainability for disabled drivers, passengers, and the general public is of primary concern. Reduced Effort Power Brake modifications should be qualified by the tests referenced in the Recommended Test Procedure. The tests set forth in that procedure should be applied, and failure of a Reduced Effort Power Brake modification to meet those tests should disqualify the modification from the claim of meeting the specifications of this Information Report. Because this is an Information Report, the numerical values for performance measurements presented in this report and
The intended upper bound of this specification is that the particle size distribution (PSD) of powders supplied shall be <60 mesh (250 µm) and that no powder (0.0 wt%) greater than 40 mesh (425 µm) is allowed.
This specification covers an aluminum alloy in the form of extruded bars, rods, wire, profiles, and tubing 2.000 inches (50.80 mm) and under in nominal diameter or least thickness (wall thickness of tubing) with a maximum cross-sectional area of 20 in2 (129 cm2), and a maximum circle size of 10 inches (254 mm) (see 8.8).
This specification establishes requirements for two types and classes of a two component, low temperature curing, polysulfide, sealing compound for use as a quick-repair material for aircraft structure.
The purpose of this document is to define design, construction, operational, and maintenance requirements for hydrogen fuel storage and handling systems in on-road vehicles. Performance-based requirements for verification of design prototype and production hydrogen storage and handling systems are also defined in this document. Complementary test protocols (for use in type approval or self-certification) to qualify designs (and/or production) as meeting the specified performance requirements are described. Crashworthiness of hydrogen storage and handling systems is beyond the scope of this document. SAE J2578 includes requirements relating to crashworthiness and vehicle integration for fuel cell vehicles. It defines recommended practices related to the integration of hydrogen storage and handling systems, fuel cell system, and electrical systems into the overall Fuel Cell Vehicle.
This specification covers non-silicone synthetic rubber sealing compounds supplied as a two-component or pre-mixed and frozen (PMF) system that cures at room temperature.
This test can be used to evaluate odor characteristics of non-metallic materials used in the interior cabin of a vehicle. The test conditions, odor panel requirements, scale for odor intensity and reporting of results are specified. The data from this test are useful when compared to data obtained from samples with known odor characteristics.
This specification covers a virgin, unfilled polytetrafluoroethylene (PTFE) in the form of extruded and sintered rods, tubes, and profiles.
Items per page:
50
1 – 50 of 222750