Results
This specification covers the installation of aircraft interior lighting for military aircraft.
This document provides recommendations to identify battery group sizes and dimensions for 6 V, 8 V, 12 V, and 24 V lead acid batteries.
This specification covers a corrosion-resistant steel in the form of sheet, strip, and plate.
This specification establishes the procedures used to produce a hard anodic coating on magnesium alloys and the properties of the coating.
This specification covers a manganese alloy in the form of powder, preforms, and a viscous mixture (paste) of the powder in a suitable binder.
This document outlines general requirements for the use of CFD methods for aerodynamic simulation of medium and heavy commercial ground vehicles weighing more than 10000 pounds. The document provides guidance for aerodynamic simulation with CFD methods to support current vehicle characterization, vehicle development, vehicle concept development, and vehicle component development. The guidelines presented in the document are related to Navier-Stokes and Lattice-Boltzmann based solvers. This document is only valid for the classes of CFD methods and applications mentioned. Other classes of methods and applications may or may not be appropriate to simulate the aerodynamics of medium and heavy commercial ground vehicle weighing more than 10000 pounds.
This SAE Standard applies to 12-volt lead-acid storage batteries that are designed specifically for start-stop operations in on-road passenger vehicles or light trucks. Included are definitions of terms, general testing recommendations, key performance characteristics, and life testing. Properties not unique to start-stop batteries should be tested according to SAE J537 or other applicable testing protocols.
This specification covers non-silicone synthetic rubber sealing compounds supplied as a two-component or pre-mixed and frozen (PMF) system that cures at room temperature.
This Purchasing Specification (PS), AMS3970/3, specifies the batch release and delivery requirements for carbon fiber fabric epoxy prepreg used for repair. This specification is applicable only when the carbon fiber fabric epoxy prepreg is used as part of the repair system defined in AMS3970 and AMS3970/1. This specification also defines the procedure and requirements for storage life extension of materials purchased against this specification. It is only applicable for materials that are qualified against AMS3970 (refer to PRI QPL AMS3970) and shall be carried out within the responsibility of the purchaser and under control of its Quality organization.
The intent of this specification is for the procurement of the material listed on the QPL; therefore, no qualification or equivalency threshold values are provided. Users that intend to conduct a new material qualification or equivalency program must refer to the Quality Assurance section of the base specification, AMS6891.
This SAE Standard provides general and dimensional specifications for beaded ends and hose fittings. These connections are intended for general applications in low-pressure automotive and hydraulic systems on automotive, industrial, and commercial products. The fittings shown are designed to be used with hoses that are intended to be retained by hose clamps. It is recommended that where step sizes or additional types of fittings are required they be designed to conform with the specifications of this document insofar as they may apply. The following general specifications shall supplement the dimensional data contained in the tables with respect to all unspecified detail.
This SAE Aerospace Standard (AS) defines the requirements for polytetrafluoroethylene (PTFE) lined, metallic reinforced, hose assemblies suitable for use in aerospace hydraulic, fuel, and lubricating oil systems at temperatures between -67 and 450 °F for Class I assemblies, -67 and 275 °F for Class II assemblies, and at nominal pressures up to 1500 psi. The hose assemblies are also suitable for use within the same temperature and pressure limitations in aerospace pneumatic systems where some gaseous diffusion through the wall of the PTFE liner can be tolerated. The use of these hose assemblies in pneumatic storage systems is not recommended. In addition, installations in which the limits specified herein are exceeded, or in which the application is not covered specifically by this standard (for example, oxygen), shall be subject to the approval of the procuring activity.
The intent of this specification is for the procurement of carbon fiber and fiberglass epoxy prepreg products with 350 °F (177 °C) cure for aerospace applications; therefore, no qualification or equivalency threshold values are provided. Users that intend to conduct a new material qualification or equivalency program must refer to the production quality assurance section (see 4.3) of this base specification, AMS6891.
This specification covers a titanium alloy in the form of extruded bars, tubes, and shapes, flash-welded rings up through 4.000 square inches (25.81 cm2) cross section, and stock for flash-welded rings (see 8.6).
This Purchasing Specification (PS) AMS3970/4 specifies the batch release and delivery requirements for film adhesive used for repair. This specification is applicable only when the film adhesive is used as part of the prepreg system as defined in AMS3970 and AMS3970/1. This specification also defines the procedure and requirements for storage life extension of materials purchased against this specification. It is only applicable for materials which are qualified and shall be carried out within the responsibility of the purchaser and under control of its Quality organization.
This specification covers a premium aircraft-quality, low-alloy steel in the form of bars, forgings, mechanical tubing, and forging stock.
AMS3970/2B gives specific information about the qualification program for carbon fiber fabric reinforced epoxy structural repair prepreg systems, curing under vacuum at 120 °C (250 °F), and a companion non-structural glass fabric prepreg used for repair of carbon fiber reinforced epoxy structures. The prepreg system shall include an epoxy film adhesive to be applied in a co-curing process with the prepreg for joint solid laminate and sandwich bonding.
This specification covers a corrosion- and heat-resistant nickel alloy in the form of bars, forgings, flash-welded rings under 4 inches (102 mm) in least cross-sectional dimension, and stock of any size for forging or flash-welded rings (see 8.3).
This Purchase Specification (PS), AMS3970/5, specifies the batch release and delivery requirements for the companion non-structural glass fiber fabric prepreg. This specification also defines the procedure and requirements for storage life extension of materials purchased against this specification. It is only applicable for materials which are qualified and shall be carried out within the responsibility of the purchaser and under control of its Quality organization.
The purpose of this document is to establish guidelines for determining the critical R134a and R1234yf refrigerant charge for off-road, self-propelled work machines as defined in SAE J1116 and agricultural tractors as defined in ANSI/ASAE S390. It will develop a minimum to maximum refrigerant charge range in which the HVAC system can maintain proper operation. Operating conditions and characteristics of the equipment will influence the optimum charge. Since these conditions and characteristics vary greatly from one application to another, careful consideration should be taken to determine the optimum R134a and R1234yf refrigerant charge for the HVAC system.
This ARP addresses the issue of passengers smoking in aircraft lavatories and the need to improve warnings about the danger of fire caused by smoking.
This SAE Recommended Practice defines flywheel configuration to promote standardization of flywheels for engine flywheel mounted torque converters. Tables 1A and 1B and Figure 1 give dimensions for flywheels mounted-type torque converters. For torque converters using drive ring overcenter type disconnect clutch, see SAE J620.
This specification covers a polytetrafluoroethylene (PTFE) resin filled with 15% graphite in the form of extruded or molded rods or tubes which are sintered after molding or, in the case of extrusions, sintered during the extrusion process.
This specification covers a corrosion and heat resistant steel in the form of welding wire.
This SAE Recommended Practice describes two-dimensional, 95th percentile truck driver, side view, seated shin-knee contours for both the accelerator operating leg and the clutch operating leg for horizontally adjustable seats (see Figure 1). There is one contour for the clutch shin-knee and one contour for the accelerator shin-knee. There are three locating equations for each curve to accommodate male-to-female ratios of 50:50, 75:25, and 90:10 to 95:5.
This test procedure is intended to apply to hydraulic pump suction filters and strainers used in automotive automatic transmissions that include hydraulic power pumps. The various paragraphs of Section 5 include a variety of tests and alternative tests that are not applicable to all filters and applications, so the engineer must specify which tests are to be performed for a particular application. These test procedures are intended to evaluate filter functional performance characteristics only, durability is not evaluated under this standard. Filter design requirements must be specified by the engineer on the filter assembly drawing, an applicable engineering specification, or summarized on an application data sheet similar to that found in this recommended practice. See Figure 6. Pressure circuit filters, both barrier and system contamination control types, are not covered under this standard. They are similar in design and construction to filters used in many hydraulic and
This recommended practice covers the requirements and qualification tests for two types of flexible all-metal hose assemblies intended for hydraulic use on missile and rocket applications at rated pressures of 4000 psi. Type I -65° to +650 °F service temperature range Type II -65° to +1000 °F service temperature range
Items per page:
50
1 – 50 of 221922