Results
This SAE Aerospace Recommended Practice (ARP) recommends a methodology to be used for the design, analysis and test evaluation of modern helicopter gas turbine propulsion system stability and transient response characteristics. This methodology utilizes the computational power of modern digital computers to more thoroughly analyze, simulate and bench-test the helicopter engine/rotor system speed control loop over the flight envelope. This up-front work results in significantly less effort expended during flight test and delivers a more effective system into service. The methodology presented herein is recommended for modern digital electronic propulsion control systems and also for traditional analog and hydromechanical systems.
This SAE Aerospace Standard (AS) establishes the requirements for heat-cured solid film lubricants. For other general or high-temperature applications, refer to AS1701. This document requires qualified products.
The following schematic diagrams reflect various methods of illustrating automotive transmission arrangements. These have been developed to facilitate a clear understanding of the functional interrelations of the gearing, clutches, hydrodynamic drive unit, and other transmission components. Two variations of transmission diagrams are used: in neutral (clutches not applied) and in gear. For illustrative purposes, some typical transmissions are shown.
This standard defines the requirements for bulk protective sleeve to provide fire resistance for aircraft hose assemblies, which will enable these assemblies to meet the requirements of AS1055. NOTE: Use of this sleeve does not eliminate the need to demonstrate that the sleeved assemblies will meet the applicable requirements of AS1055.
This standard is applicable to the marking of aerospace vehicle electrical wires and cables using ultraviolet (UV) lasers. This standard specifies the process requirements for the implementation of UV laser marking of aerospace electrical wire and cable and fiber-optic cable to achieve an acceptable quality mark using equipment designed for UV laser marking of identification codes on aerospace wire and cable. Wiring specified as UV laser markable subject to AS4373 and which has been marked in accordance with this standard will conform to the requirements of AS50881.
This ARP describes methods that are known to have been used by aircraft manufacturers to evaluate aircraft aerodynamic performance and handling effects following application of aircraft ground deicing/anti-icing fluids (“fluids”), as well as methods under development. Guidance and insight based upon those experiences are provided, including: Similarity analyses. Icing wind tunnel tests. Flight tests. CFD and other numerical analyses. This ARP also describes: The history of evaluation of the aerodynamic effects of fluids. The effects of fluids on aircraft aerodynamics. The testing for aerodynamic acceptability of fluids for SAE and regulatory qualification performed in accordance with AS5900. Additionally, Appendices A to E present individual aircraft manufacturers’ histories and methodologies, which substantially contributed to the improvement of knowledge and processes for the evaluation of fluid aerodynamic effects, and Appendix F considers the modeling of fluid removal from
This procurement specification covers tubular, blind rivets fabricated from a corrosion resistant nickel-copper alloy of the type identified under the Unified Numbering System as UNS N04405, and of 52 ksi minimum shear strength for self-plugging style rivets.
This SAE Recommended Practice identifies graphic symbols used in electrical circuit diagrams. The symbols aid troubleshooting electrical systems.
This document contains procedures for performance testing of electrical terminals, connectors, and components for coaxial-style cable with an outside cable diameter of 3.6 mm and smaller. These are often called “mini coax connector systems.” This specification applies to coaxial cable connection systems that operate at frequencies from DC to 9 GHz and are intended for road vehicles. The characteristic impedance of the mini coax connection system described here is 50 Ω, however nothing excludes the use of these connectors in systems with a different characteristic impedance. This specification applies only to connection systems using coaxial cable.
This specification, in conjunction with the general requirements for steel heat treatment covered in AMS2759, establishes the requirements for heat treatment of carbon and low-alloy steel parts to minimum ultimate tensile strengths below 220 ksi (1517 MPa). Parts are defined in AMS2759. Due to limited hardenability in these materials, there are size limits in this specification.
This SAE Aerospace Information Report (AIR) identifies the risks and dangers associated with the carriage and use of pyrotechnic signaling devices in transport category aircraft life rafts and slide/rafts, and provides a rationale for allowing the use of alternative non-pyrotechnic devices authorized by FAA/TSO-C168. These devices offer an equivalent level of safety while eliminating flight safety risks, enhancing survivability of aircraft ditching survivors, reducing costs, eliminating dangerous goods transportation and handling issues, and reducing environmental impact of dangerous goods disposal.
This specification covers established manufacturing tolerances applicable to low-alloy steel bars ordered to inch/pound dimensions. These tolerances apply to all conditions, unless otherwise noted. The term “exclusive” is used to apply only to the higher figure of the specified range.
This SAE Standard was developed to provide a method for indicating the direction of engine rotation and numbering of engine cylinders. The document is intended for use in designing new engines to eliminate the differences which presently exist in industry.
This specification covers an aluminum alloy in the form of castings (see 8.6).
To define a list of anomalies related to OBD Communications. Misinterpretations of various OBD Communications Standards and Recommended Practices have resulted in OBD “no-communications” situations in the field. This Information Report identifies the most prevalent of these.
This specification covers an aluminum alloy in the form of sheet, clad on one side.
SAE J115 specifies the relevant ISO standards for application to safety labels for use on off-road work machines as defined in SAE J1116.
Items per page:
50
1 – 50 of 219833