Results
This SAE Standard establishes the test procedure, environment, and instrumentation for determining the sound levels of snowmobiles in the stationary test mode. This test method is intended to provide an accurate measurement of exhaust and other engine noise and may be used to evaluate new and in-use snowmobiles to determine compliance with noise control regulations. Sound level measurements obtained with this test method are not intended as an engineering determination of overall machine noise. For this purpose, the use of SAE J192 is recommended.
This document addresses the operational safety and human factors aspects of unauthorized laser illumination events in navigable airspace. The topics addressed include operational procedures, training, and protocols that flight crew members should follow in the event of a laser exposure. Of particular emphasis, this document outlines coping strategies for use during critical phases of flight. Although lasers are capable of causing retinal damage, most laser cockpit illuminations, to date, has been relatively low in irradiance causing primarily startle reactions, visual glare, flashblindness and afterimages. Permanent eye injuries from unauthorized laser exposures have been extremely rare. This document describes pilot operational procedures in response to the visual disruptions associated with low to moderate laser exposures that pilots are most likely to encounter during flight operations. With education and training, pilots can take actions that safeguard both their vision and the
This Aerospace Standard (AS) covers the general minimum performance standards for generators/starter-generators and associated voltage regulators for use in direct current (DC) electric systems for civil aircraft.
This document covers the recommended lighting performance and design criteria for: Left Forward Navigation Position Lights (Red) Right Forward Navigation Position Lights (Green) Rear Navigation Position Lights (White) Anticollision Lights. AS8017 provides for the following classes: Class I Rotorcraft, Class II Fixed Wing, and Class III Fixed Wing and Rotorcraft. Possible design requires include but are not limited to: Red Flashing Lights Top and Bottom Fuselage White Flashing Strobe Lights Wing Tips and/or Tail Red Flashing Beacon Light on Top of Vertical Tail
This specification covers an aluminum alloy in the form of pre-alloyed powder.
This specification covers a premium aircraft-quality, high-strength, low-alloy steel in the form of bars, forgings, mechanical tubing, flash welded rings, and stock for forging or flash welded rings.
This specification covers an aircraft-quality, low-alloy steel in the form of bars, forgings, flash-welded rings, and stock for forging or flash-welded rings.
This specification covers a premium aircraft-quality, high-alloy steel gas-atomized and HIP-consolidated in the form of bars, wire, forgings, and forging stock.
Scope is unavailable.
This document establishes common industry practices and recommended screening, qualification, and lot acceptance testing of Plastic Encapsulated Microcircuits (PEMs) for use in space application environments.
The intent of this document is to define the methodology for suspect parts inspection using radiological inspection. The purpose of radiology for suspect counterfeit part inspection is to detect deliberate misrepresentation of a part, either at the part distributor or original equipment manufacturer (OEM) level. Radiological inspection can also potentially detect unintentional damage to the part resulting from improper removal of part from assemblies, which may include, but not limited to, prolonged elevated temperature exposure during desoldering operations or mechanical stresses during removal. Radiological inspection of electronics includes film radiography and filmless radiography such as digital radiography (DR), real time radiography (RTR), and computed tomography (CT). Radiology is an important tool used in part verification of microelectronic devices. Radiographic analysis is performed on parts to verify that the internal package or die construction is consistent with an
XRF technique for counterfeit detection is applicable to electrical, electronic and electromechanical (EEE) parts as listed in AS6171 General Requirements. In general, the detection technique is meant for use on piece parts prior to assembly on a circuit board or on the parts that are removed from a circuit board. The applicability spans a large swath of active, passive and electromechanical parts. If AS6171/3 is invoked in the contract, the base document, AS6171 General Requirements shall also apply.
This document covers insulated, flexible air duct assemblies for portable ground support air conditioners and heaters.
This SAE Recommended Practice describes the dynamic testing procedures required to evaluate the integrity of patient compartment interior Storage Compartments such as cabinets, drawers, or refillable supply pouch systems when exposed to a frontal, side or rear impact (i.e., a crash impact). Its purpose is to provide component manufacturers, ambulance builders, and end-users with testing procedures and, where appropriate, acceptance criteria that, to a great extent, ensure interior Storage Compartments or systems meet the same performance criteria across the industry. Descriptions of the test set-up, test instrumentation, photographic/video coverage, test fixture, and performance metrics are included.
This SAE Aerospace Recommended Practice (ARP) provides recommendations for the design and test requirements for a spring-loaded, normally-closed hydraulic check valve. The check valve is intended for use in a civil or military aircraft hydraulic system with a rated system pressure up to 5000 psi (34500 kPa).
While this report does not include a discussion of all of the available data defining human response or address all body areas, for those areas addressed it does utilize references generally judged by those in the field to be practical and meaningful guidelines for the development of human surrogates. This report is intended to be a “living” document that will be updated periodically. A number of problems need to be addressed in defining human impact response characteristics. There is the problem of human response variability from subject to subject in volunteer tests. There is the problem of extrapolating such volunteer data which are obtained at low impact severities to higher impact severities using human cadaver response data obtained at injurious levels of impacts. Live animal experiments have been conducted over the years in an attempt to define human impact response and tolerance. The problem with using animal response data is the lack of geometric scaling techniques needed to
Items per page:
50
1 – 50 of 220040