Results
This specification covers a low-alloy steel in the form of bars, forgings, mechanical tubing, and forging or tubing stock.
This supplement forms a part of SAE Aerospace Specification AS85421. It shall be used to identify fitting standards citing this procurement specification.
This SAE Standard establishes the test procedure, environment, and instrumentation for determining the sound levels of snowmobiles in the stationary test mode. This test method is intended to provide an accurate measurement of exhaust and other engine noise and may be used to evaluate new and in-use snowmobiles to determine compliance with noise control regulations. Sound level measurements obtained with this test method are not intended as an engineering determination of overall machine noise. For this purpose, the use of SAE J192 is recommended.
This specification covers a nitrile (NBR) rubber in the form of sheet, strip, tubing, extrusions, and molded shapes.
This SAE Aerospace Recommended Practice (ARP) provides to the aerospace industry a procedure for the consistent and accurate calculation of fuel flow using turbine flowmeters during development, production, and post overhaul/repair gas turbine engine testing.
This SAE Aerospace Standard (AS) establishes the minimum standard requirements for message boards (MBs) at designated deicing facilities. The design of aircraft deicing facilities is covered by ARP4902. Standards for the deicing facility management system are outside the scope of this document.
This SAE Aerospace Recommended Practice (ARP) defines minimum requirements for an aircraft transport ULD to transport horses properly and safely by air, to protect the horse(s) from injuries, and to protect the aircraft from corrosion created by waste spill. The ULD is designed to accommodate one horse or several. There are two types of ULDs for aircraft transportation of horses:
This SAE Aerospace Recommended Practice (ARP) contains methods used to measure the optical performance of airborne electronic flat panel display (FPD) systems. The methods described are specific to the direct view, liquid crystal matrix (x-y addressable) display technology used on aircraft flight decks. The focus of this document is on active matrix, liquid crystal displays (LCD). The majority of the procedures can be applied to other display technologies, however, it is cautioned that some techniques need to be tailored to different display technologies. The document covers monochrome and color LCD operation in the transmissive mode within the visual spectrum (the wavelength range of 380 to 780 nm). These procedures are adaptable to reflective and transflective displays paying special attention to the source illumination geometry. Photometric and colorimetric measurement procedures for airborne direct view CRT (cathode ray tube) displays are found in ARP1782. Optical measurement
This User Guide describes the content of the Rational Software Architect (RSA) version of the UCS Architectural Model and how to use this model within the RSA modeling tool environment. The purpose of the RSA version of the UCS Architectural Interface ICD model is to provide a model for Rational Software Architect (RSA) users, derived from the Enterprise Architect (EA) ICD model (AIR6515). The AIR6515 EA Model, and by derivation, the AIR6516 RSA Model, have been validated to contain the same content as the AS6518 model for: all UCS ICD interfaces all UCS ICD messages all UCS ICD data directly or indirectly referenced by ICD messages and interfaces the Domain Participant, Information, Service and Non-Functional Properties Models
This document and the EUROCAE equivalent, ED-107, provides detailed information, guidance, and methods in support of the Federal Aviation Administration (FAA) Advisory Circular (AC) 20-158 and to the European Union Aviation Safety Agency (EASA) AMC 20-158. AC 20-158 provides a means, but not the only means, for demonstrating compliance with Title 14 of the Code of Federal Regulations (14 CFR) 23.1308 (Amendment 57 and lower), 23.2520 (Amendment 64 and higher), 25.1317, 27.1317, 29.1317, and applicable FAA HIRF special conditions addressing HIRF Protection. AMC 20-158 is applicable to Certification Specifications CS 23.1308 (Amendment 4 and lower), 23.2520 (Amendment 5 and higher), 25.1317, 27.1317, and 29.1317. It should be noted that this document is neither mandatory nor regulatory in nature and does not constitute a regulation or legal interpretation of the regulation. Therefore, an applicant may elect to establish an alternative method of compliance that is acceptable to the
This SAE Part Standard covers selected inch dimensioned tapping screws and metallic drive screws manufactured in accordance with American Society for Mechanical Engineers dimensional standards. This SAE standard covers material most often used in ship systems and equipment but its use may be applied wherever fasteners of the covered materials are used. This standard permits the fasteners to be identified and ordered by a Part Identification Number (PIN) as defined in this standard.
This specification covers a premium aircraft-quality, low-alloy steel in the form of bars, forgings, mechanical tubing, and forging stock.
This Aerospace Standard (AS) covers the general minimum performance standards for generators/starter-generators and associated voltage regulators for use in direct current (DC) electric systems for civil aircraft.
The previous revision of AIR5784 summarizes some of the available literature on cabin air study, engine oil composition, decomposition, and toxicity testing. This revision of AIR5784 includes literature and information on stakeholder involvement, selected air sampling studies, oil composition, and oil degradation, published from 2000 to 2023. The entire contents of the reviewed literature are not necessarily endorsed by either SAE or the members of the study group who produced it. This is not a comprehensive review but is intended to enable E-34 and other technical organizations to participate in informed discussions on the topic. Also, the review is intended to indicate where additional work may be necessary to properly gauge the potential role that turbine lubricants (and OPs) play in cabin air quality. The toxicology of oil fumes and their individual constituents is beyond the scope of this document and outside the remit of this committee.
This SAE Aerospace Information Report (AIR) discusses characteristics of data communications for the Joint Architecture for Unmanned Systems (JAUS). This document provides guidance on the aspects of transport media, unmanned systems and the characteristics of JAUS itself that are relevant to the definition of a JAUS transport specification.
This Aerospace Standard (AS) defines the requirements for a metallic reinforced, duct assembly suitable for use in low pressure, 350 °F ground heaters.
This SAE Recommended Practice provides dimensional specifications for the 41/2 and 53/4 inch general service sealed lighting units, intended for use in such applications as motorcycle headlamps, military headlamps, industrial machinery headlamps, fog lamps, spot lamps, etc. See Figures 1 and 2 and Tables 1 and 2.
This document describes a rigorous-engineering fuel-consumption test procedure that utilizes industry accepted data collection and statistical analysis methods to determine the change in fuel consumption for trucks and buses with gross vehicle weight rating (GVWR) of more than 10000 pounds, equipped with internal combustion engines using diesel, gasoline, or their liquid substitutes. The test procedure may be conducted on a test track or on a public road under controlled conditions and supported by extensive data collection and data analysis constraints. The on-road test procedure is offered as a lower cost alternative to on-track testing, but the user is cautioned that on-road test may result in lower resolution (or precision) data due to a lack of control over the test environment. Test results that do not rigorously follow the method described herein are not intended for public use and dissemination and shall not be represented as an SAE J1321-Type II test result. This document
This specification establishes the requirements for self-locking nuts, wrenching type (i.e., hexagon, double hexagon, and spline drive), made of a corrosion and heat resistant steel of the type identified under the Unified Numbering System as UNS S66286.
This specification covers all metal, self-locking wrenching nuts, plate nuts, shank nuts, and gang channel nuts made of a carbon or low alloy steel.
This specification covers an adhesive compounded from modified epoxy resins in ready-to-use film supplied in rolls or sheets, either supported by mat or by woven monofilaments or unsupported.
Items per page:
50
1 – 50 of 221110