Results
This test method provides a procedure for measuring no-load rotational breakaway torque of self-lubricating spherical bearings.
The primary objective of this recommended practice is to confirm that vehicles can communicate a minimum set of information in accordance with diagnostic test services specified in SAE J1979-2, or the equivalent ISO 14229-1:2013 (Ed. 2) and SAE J1979-3 documents. A successful result using the SAE J1699-5 Automotive Alliance for Innovation (AAI) software for OBD-II testing indicates that the main aspects of UDS communication have been examined, but it does not provide assurance of complete compliance with all aspects of SAE J1979-2 or SAE J1979-3. SAE J1699-5 tests run with a SAE J2534 device hardware and API that is not fully compliant will result in a test failure. This specification takes precedence over all conflicts in the documents cited in this section.
This SAE Information Report provides SAE’s recommendations for meeting the requirements for Real Emissions Assessment Logging (REAL) oxides of nitrogen (NOx) accuracy demonstration and for the implementation of REAL NOx binning requirements as defined in onboard diagnostics (OBD) regulations 13 CCR 1971.1 and 13 CCR 1968.2.
This SAE Information Report establishes a uniform procedure for assuring the manufactured quality, installed utility, and performance of automotive remote steering controls other than those provided by the vehicle manufacturer (OEM). These products are intended to provide driving capability to persons with physical disabilities. The adaptive modifications seek to compensate for lost or reduced function in the extremities of the driver with a disability. Remote steering controls are designed to provide a steering input device alternative to the OEM steering wheel that either reduces the required input force, changes the required range of motion or changes the location of the steering control, or any combination of the above. These controls supplement by power, other than by the driver’s own muscular efforts, the force output of the driver with a disability. Because this is an Information Report, the numerical values for performance measurements presented in this report and in the
This SAE Aerospace Information Report (AIR) describes procedures for use in the field to determine if 115/200 Volt, 400 Hz aircraft external electrical power connectors are excessively worn, which may result in the inability of the external power plug to be retained, intermittent electrical performance, and arcing.
This specification covers a corrosion- and heat-resistant nickel alloy in the form of plate nominally 2.00 inches (50.8 mm) and under in thickness, inclusive.
This specification covers a corrosion- and heat-resistant cobalt alloy in the form of bars, forgings, flash-welded rings, and stock for forging or flash-welded rings.
This specification covers pure gold in the form of wire 0.005 to 0.040 inch (0.012 to 1.000 mm), inclusive, in nominal diameter and ribbon 0.002 to 0.051 inch (0.05 to 1.28 mm), inclusive, in nominal thickness (see 8.5).
This specification, in conjunction with the general requirements for steel heat treatment covered in AMS2759, establishes the requirements for heat treatment of precipitation-hardening corrosion-resistant, maraging, and secondary hardening steel parts. Parts are defined in AMS2759. Parts made from steels other than those specified in this specification may be heat treated in accordance with the applicable requirements herein using processing temperatures, times, and other parameters recommended by the material producer unless otherwise specified by the cognizant engineering organization. General ordering instructions are specified in AMS2759.
This specification covers a corrosion- and heat-resistant nickel alloy in the form of sheet, strip, and plate.
This SAE Recommended Practice was developed primarily for gasoline-powered passenger car and truck applications to interface vapor recovery systems, but it may be used in diesel, marine, industrial, and similar applications where a nozzle is required for filling. The zones cover nozzle spout access and handle clearance to a refilling port. In addition, this recommended practice includes a design window for nozzle manufacturers to develop with.
This specification covers a corrosion-resistant steel in the form of sheet, strip, and plate.
This specification covers a corrosion- and heat-resistant nickel alloy in the form of seamless tubing.
This specification covers a corrosion-resistant steel in the form of investment castings.
This specification covers a magnesium alloy in the form of investment castings (see 8.6).
This specification covers a carbon steel in the form of sheet and strip.
This SAE Recommended Practice is intended for stakeholders of the automotive industry that are conducting emission testing on materials, parts, or components used in automotive interiors. Testing methods may specifically define the handling and packaging conditions for the material to be analyzed. In these cases, follow the method as closely as possible. Use this document as a guide where the protocol for handling and packaging the samples between production and testing may be undefined or ambiguous.
This SAE Standard was developed to provide a method for indicating the direction of engine rotation and numbering of engine cylinders. The document is intended for use in designing new engines to eliminate the differences which presently exist in industry.
This specification covers an aluminum alloy in the form of die forgings, hand forgings, and forging stock.
This specification covers a carbon steel in the form of sheet and strip.
This specification covers a premium aircraft-quality corrosion and heat-resistant steel in the form of bars, forgings, mechanical tubing, and forging stock.
This specification covers a permanently mastic polysulfide compound in the form of a paste.
This Handbook is intended to accompany or incorporate AS5643, AS5643/1, AS5657, AS5706, and ARD5708. In addition, full understanding of this Handbook also requires knowledge of IEEE-1394-1995, IEEE-1394a, and IEEE-1394b standards. This Handbook contains detailed explanations and architecture analysis on AS5643, bus timing and scheduling considerations, system redundancy design considerations, suggestions on AS5643-based system configurations, cable selection guidance, and lessons learned on failure modes.
This standard establishes the common requirements for training of DPRV personnel for use at all levels of the aerospace engine supply chain. This standard shall apply when an organization elects to delegate product release verification by contractual flow down to its suppliers (reference 9100 and 9110 standards) and to perform product acceptance on its behalf. It is intended that organizations specify their DPRV requirements through the application of AS9117. While the delegating organization will use the AS13001 standard as the baseline for establishing DPRV process and product training, it may include additional contractual training requirements to meet its specific needs. The DPRV training material was primarily developed for aerospace engine supply chain requirements. However, this standard may also be used in other aerospace industry sectors where a DPRV process requiring specific training can be of benefit.
This SAE Recommended Practice is part of the SAE J2534-2/X_0500 set of documents that extends the SAE J2534-1_0500 API (version 05.00) specification, and defines how to implement CAN with flexible data rate (CAN FD) within the SAE J2534 API framework. This document details only the changes from SAE J2534-1_0500 and items not specifically detailed in this document are assumed to have not changed. An SAE J2534-2/11_0500 interface shall be compliant to the CAN with flexible data rate (CAN FD) feature only when all the required functionality in this SAE Recommended Practice is implemented. Any functionality not required for compliance will be specifically marked as “optional” in this document. This document must be used in conjunction with the SAE J2534-2/BA_0500 and SAE J2534-2/RE_0500 documents.
This SAE Aerospace Recommended Practice (ARP) establishes the minimum recommended Test Stand Setup and Procedures for inspecting and testing Aircraft Refuelers. The inspection and test procedure shall be used to evaluate the operation and performance of an Aircraft Refueler to assure that it meets the minimum refueling performance criteria and is fit for aircraft fueling and/or defueling operations. These procedures shall be used to test new Aircraft Refuelers and may be used to perform routine tests to confirm that the Aircraft Refuelers comply with the minimum performance criteria as specified herein. This document covers all types of Aircraft Refuelers, stationary (e.g., cabinet type units) or mobile (e.g., hydrant service vehicles, tankers, etc.).
This SAE Recommended Practice provides a test procedure for eddy current speedometers, including the odometer if an integral portion of the speedometer, for passenger car service.
This specification covers a corrosion and heat-resistant steel in the form of welding wire.
This specification covers a premium grade titanium alloy in the form of investment castings.
This specification covers established inch/pound manufacturing tolerances applicable to carbon steel sheet, strip, and plate ordered to inch/pound dimensions. These tolerances apply to all conditions unless otherwise noted. The term “excl” is used to apply only to the higher figure of the specified range. Tolerances for product sizes not listed herein shall be as agreed upon by purchaser and vendor.
The function of a multifunctional display (MFD) system is to provide the crew access to a variety of data, or combinations of data, used to fly the aircraft, to navigate, to communicate, and to manage aircraft systems. MFDs may also display primary flight information (PFI) as needed to insure continuity of operations. This document sets forth design and operational recommendations concerning the human factors considerations for MFD systems. The MFD system may contain one or more electronic display devices capable of presenting data in several possible formats. MFDs are designed to depict PFI, navigation, communication, aircraft state, aircraft system management, weather, traffic, and/or other information used by the flight crew for command and control of the aircraft. The information displayed may be combined to make an integrated display or one set of data may simply replace another. The information contained in this document can be applied to the design of all MFDs, including
This specification covers aluminum alloy die forgings and hand forgings.
Items per page:
50
1 – 50 of 222741