Results
This document defines the test procedures and performance limits of steady state and transient voltage characteristics for 12 V, 24 V, or 48 V electrical power generating systems used in commercial ground vehicles.
The importance of reliability in design engineering has significantly grown since the early 1960’s. Competition has been a primary driver in this growth. The three realities of competition today are: world class quality and reliability, cost-effectiveness, and fast time-to-market. Formerly, companies could effectively compete if they could achieve at least two of these features in their products and product development processes, often at the expense of the third. However, customers today, whether military, aerospace, or commercial, have been sensitized to a higher level of expectation and demand products that are highly reliable, yet affordable. Product development practices are shifting in response to this higher level of expectation. Today, there is seldom time, or necessary resources to extensively test, analyze, and fix to achieve high quality and reliability. It is also true that the rapid growth in technology prevents the accumulation of historical data on the field performance
Document provides information on how military/commercial/gas turbine engine test cell/system users may benefit from this unique Coanda/Refraction concept.
This document applies to the requirements of a device used in the field and inspection stations to aim and check aim of mechanically aimable headlamp units. The purpose of this document is to provide a laboratory test procedure to determine whether the devices under test are capable of accurately positioning headlamp units from their aiming pads and maintaining their accuracy in service within the tolerances designated in this document.
The SAE International task force on headlamp mounting height has considered the ramifications of reducing the maximum mounting height of headlamps on highway vehicles. The task force has concluded that it is in the best interest of the driving public to make a substantial reduction in the recommended maximum height at which headlamps, particularly low-beam headlamps, may be mounted. Heights as low as 36 to 40 in (90 to 100 cm) have been considered. New tractor vehicles are in fact being designed with headlamps mounted in this range. Further recommendations were withheld in anticipation of tests to demonstrate the effect of mounting height on the legibility of certain overhead signs.
This SAE standard applies to any and all additives and chemical solutions intended for aftermarket use in the refrigerant circuit of vehicle air-conditioning systems with belt-driven compressors, except as noted below. This standard provides testing and acceptance criteria for determining the stability and compatibility of additives and flushing materials (solutions) with A/C system materials and components, that may be intended for use in servicing or operation of vehicle air conditioning systems. This standard does not provide test criteria for additive, compressor lubricant, or flushing solution effectiveness; such testing is the responsibility of the additive and/or solution manufacturer/supplier. This standard does not cover additives or flushing materials for electrically driven compressors. The use of additives with electrically driven compressors might cause electrical shorting and compressor failure. It is not the intent of this document to identify the requirements for
This document provides the technical requirements for implementing the SAE J1939 Functional Safety Communication Protocol in a manner determined suitable for meeting industry applicable functional safety standards.
This SAE Information Report prescribes dummies, procedures, and configurations that can be used for investigating the interactions that might occur between a deploying airbag and a child restrained by a child restraint system (CRS). During the inflation process, airbags generate a considerable amount of kinetic energy which can result in substantial forces being applied to a child who is restrained in a CRS in the front seat of a vehicle. Field data collected by the special crash investigation team of the National Highway Traffic Safety Administration (NHTSA) indicate that fatal forces can be developed. In response to these field data, NHTSA added a series of airbag/child interaction tests and limits to the Code of Federal Regulations (CFR 571.208) that deal with occupant protection, commonly known as Federal Motor Vehicle Safety Standards (FMVSS 208). The bases for NHTSA tests are the various test procedures that were developed by the International Standards Organization (ISO) and the
This SAE Recommended Practice defines test methods and general requirements at all phases of development, production, and field analysis of electrical terminals (including sense pins), connectors, and components that constitute the jump-start connection for road vehicles having 42 V (nominal) electrical systems. The 42 V jump start connector is always remote from the vehicle battery and may take the form of an in-line or Header Connection, either of which is in an accessible location for attachment of a jumper cable from an assist vehicle or battery charger. WARNING—The Jump Start Connector requires environmental protection. This specification assumes that such protection is in place and remains effective for the life of the vehicle. The level of protection depends on the vehicle packaging environment and duty cycle. Appendix B of this document contains the physical specification for the Jump Start Connector.
The information in this document is intended to apply to commercial jet transport category airplanes that incorporate plastic (polycarbonate or acrylic) lenses on exterior light assemblies, or are being considered for such an application as opposed to glass lens designs. Exterior lighting applications include position light assemblies, anticollision light asemblies, and landing light assemblies. However, much of the material provided herein is general in nature and is directly applicable to many aircraft categories including, but not limited to, helicopters, general aviation aircraft, and military aircraft.
This SAE Recommended Practice establishes a standard method to perform screening test sequences that identify a brake friction material’s effectiveness under various test conditions. The result is an evaluation of brake friction material effectiveness under a set of defined braking conditions considered most relevant to automobile braking system development.
This specification covers a cobalt alloy in the form of wire, rod, strip, foil, and powder and a viscous mixture (paste) of the powder in a suitable binder.
This SAE Standard provides a system for specifying significant material properties of thermoplastic elastomers (TPEs) that are intended for, but not limited to, use in automotive applications. In all cases where provisions of this classification system would conflict with those of the detailed specifications for a particular product, the latter shall take precedence. This classification is based on SI units.
This specification covers one type of epoxy-resin-impregnated carbon fibers in the form of eight harness satin fabric woven from continuous fiber tow.
AS5653 may be applied to Air Vehicles and Stores implementing MIL-STD-1760 Interface Standard for Aircraft/Store Electrical Interconnection System.
This SAE Recommended Practice has been established to provide direction for the design and installation of an identification number (IN) as assigned to vehicle engines, transmissions, and transaxles. The IN is used for tracking or traceability of these components. In adhering to these recommended practices, facility of application in factory production and appearance quality are matters for manufacturer control. Reference SAE J853.
This specification covers the recommended design, construction, performance and testing requirements for aircraft wheel inflation valves incorporating an inflation pressure gauge which are mounted on the aircraft wheel. These valve/gauge assemblies should be appropriate for use on all aircraft types supported by tubeless tire/wheel assemblies.
This SAE Recommended Practice applies to highway trailer tow bar eye-type applications, including multiple trailers.
This SAE Standard describes head position contours and procedures for locating the contours in a vehicle. Head position contours are useful in establishing accommodation requirements for head space and are required for several measures defined in SAE J1100. Separate contours are defined depending on occupant seat location and the desired percentage (95 and 99) of occupant accommodation. This document is primarily focused on application to Class A vehicles (see SAE J1100), which include most personal-use vehicles (passenger cars, sport utility vehicles, pick-up trucks). A procedure for use in Class B vehicles can be found in Appendix B.
The air cranking system components, which include the tank, valve, hose, and starter, must be carefully selected to provide the necessary speed to start an engine under the most severe climatic conditions for which the system is intended. Engine cranking loads increase with cold temperatures, therefore, the initial selection of these components, needs to consider low-temperature engine torque requirements. To insure an adequate air cranking system is obtained, it is important that proper test procedures are used for obtaining the cranking load requirements of the engine.
This Aerospace Recommended Practice (ARP) clarifies terms used in Aerospace materials and process specifications. The terms clarified in this ARP are not intended to supersede those terms for which clarification is already provided in existing specifications.
Items per page:
50
1 – 50 of 221567