Results
This supplement forms a part of SAE Aerospace Specification AS85421. It shall be used to identify fitting standards citing this procurement specification.
This SAE Standard establishes the test procedure, environment, and instrumentation for determining the sound levels of snowmobiles in the stationary test mode. This test method is intended to provide an accurate measurement of exhaust and other engine noise and may be used to evaluate new and in-use snowmobiles to determine compliance with noise control regulations. Sound level measurements obtained with this test method are not intended as an engineering determination of overall machine noise. For this purpose, the use of SAE J192 is recommended.
This SAE Aerospace Recommended Practice (ARP) establishes the minimum recommended Test Stand Setup and Procedures for inspecting and testing Aircraft Refuelers. The inspection and test procedure shall be used to evaluate the operation and performance of an Aircraft Refueler to assure that it meets the minimum refueling performance criteria and is fit for aircraft fueling and/or defueling operations. These procedures shall be used to test new Aircraft Refuelers and may be used to perform routine tests to confirm that the Aircraft Refuelers comply with the minimum performance criteria as specified herein. This document covers all types of Aircraft Refuelers, stationary (e.g., cabinet type units) or mobile (e.g., hydrant service vehicles, tankers, etc.).
This SAE Aerospace Information Report (AIR) provides descriptions of aircraft flight control actuation system failure-detection methods. The fault-detection methods are those used for ground and in-flight detection of failures in electrohydraulic actuation systems for primary flight controls.
The scope of this SAE Recommended Practice is restricted to the testing of original equipment on passenger vehicles and to provide for a uniform industry test procedure.
This document is a result of the desire for interoperability of modules on a Pi-Bus. This standard is a stand alone document that used the Very High Speed Integrated Circuit (VHSIC) Phase 2, Interoperability Standard Pi-Bus Specification 2.2, as a starting point.
This SAE Recommended Practice is applicable to two- or three-wheel motorcycles intended for highway use. Unless noted, requirements apply to both metallic and nonmetallic tanks. Accessory or aftermarket tanks as well as original equipment tanks are covered.
This SAE Recommended Practice applies to the boomstop for the main boom of all mobile construction type cranes having rope supported booms, equipped for hook work, clamshell, magnet, grapple, or concrete bucket attachments.
This SAE Standard applies to the application of ultraviolet leak detection to service mobile air-conditioning systems.
This SAE Recommended Practice describes the equipment and procedure for determining the truck cab interior sound level over the upper half of the engine speed range. This practice applies to motor trucks and truck-tractors and does not include construction and industrial machinery.
This SAE Standard was developed to provide a method for indicating the direction of engine rotation and numbering of engine cylinders. The document is intended for use in designing new engines to eliminate the differences which presently exist in industry.
This specification covers a nitrile (NBR) rubber in the form of sheet, strip, tubing, extrusions, and molded shapes.
This specification covers a titanium alloy in the form of bars and forgings up through 10.000 inches (254.00. mm), inclusive, in diameter or least distance between parallel sides with a maximum cross-sectional area of 79.0 in2 (506.45 cm2) and forging stock of any size (see 8.7).
This specification establishes the requirements and procedures for producing a hard, wear resistant ion nitrided surface on steel parts.
This specification covers a polytetrafluoroethylene (PTFE) resin filled with 15% graphite in the form of extruded or molded rods or tubes which are sintered after molding or, in the case of extrusions, sintered during the extrusion process.
This SAE Recommended Practice describes two-dimensional, 95th percentile truck driver, side view, seated shin-knee contours for both the accelerator operating leg and the clutch operating leg for horizontally adjustable seats (see Figure 1). There is one contour for the clutch shin-knee and one contour for the accelerator shin-knee. There are three locating equations for each curve to accommodate male-to-female ratios of 50:50, 75:25, and 90:10 to 95:5.
This SAE Standard covers the mechanical and material requirements for eight property classes of steel, externally threaded metric fasteners in sizes M1.6 through M36, inclusive, and suitable for use in automotive and related applications.
This specification covers a corrosion and heat-resistant nickel alloy in the form of seamless tubing having nominal OD of 0.125 inch (3.18 mm) and over with nominal wall thickness of 0.015 inch (0.38 mm) and over (see 8.5).
Wire and cable products progress through a series of handling or operational steps from the time they leave the manufacturer, and until a finished harness or assembly is ready for installation on a vehicle. Throughout these many steps, environmental or processing conditions may be present which can generate damage detrimental to the wire or cable and/or its intended application.
This procurement specification covers aircraft-quality solid rivets made from a corrosion resistant nickel-copper alloy of the type identified under the Unified Numbering System as UNS N04400 and of 46 ksi minimum shear strength.
This specification presents requirements for the heat treatment of parts and components fabricated from wrought (plate, sheet, strip, bar, rod, wire extrusions and tube and forgings) copper alloys, numbers C17000, C17200, C17300, C17500, and C17510 (see 6.7). This specification also covers “bright hardening”.
This specification covers a polytetrafluoroethylene (PTFE) modified fluorosilicone (FVMQ) rubber in the form of molded shapes, molded rings (ASTM D 1414), and compression seals.
This SAE Aerospace Standard (AS) establishes the requirements for AS3504 and AS3505 thin wall self-locking inserts made from a corrosion and heat resistant, age hardenable nickel base alloy of the type identified under the Unified Numbering System as UNS N07718.
This specification covers acrylic-monomer base adhesives intended for use in bonding acrylic plastics.
Items per page:
50
1 – 50 of 220496