Results
This document defines the test procedures and performance limits of steady state and transient voltage characteristics for 12 V, 24 V, or 48 V electrical power generating systems used in commercial ground vehicles.
This specification covers a low-alloy steel in the form of bars, forgings, mechanical tubing, and forging or tubing stock.
This TIR establishes high-flow fueling protocols, including their process limits for fueling of compressed gaseous hydrogen vehicles at peak flow rates from 60 to 300 g/s with compressed hydrogen storage system (CHSS) volume capacities between 248.6 and 7500 L which have been qualified to UN GTR #13. This document is initially being published as a TIR due to limited field testing of the fueling protocols. Once the fueling protocols have been field tested, the SAE Fuel Cell Standards Committee Interface Task Force intends to publish a revision to this document as an SAE Standard.
This specification defines limits of variation for determining acceptability of composition of cast and wrought corrosion and heat-resistant steels and alloys, maraging and other highly alloyed steels, and iron alloy parts and materials acquired from a producer.
The purpose of this section is to provide methods and a set of convenient working charts to estimate penalty values in terms of take-off fuel weight for any given airplane mission. The curves are for a range of specific fuel consumption (SFC) and lift/drag ratio (L/D) compatible with the jet engines and supersonic aircraft currently being developed. A typical example showing use of the charts for an air conditioning system is given. Evaluation of the penalty imposed on aircraft performance characteristics by the installation of an air conditioning system is important for two reasons: 1 It provides a common denominator for comparing systems in the preliminary design stage, thus aiding in the choice of system to be used. 2 It aids in pinpointing portions of existing systems where design improvements can be most readily achieved. All factors that influence the flight performance of an aircraft can be expressed in terms of weight, external and momentum drags, and changes in powerplant
This document is a companion document to SAE AS4893 “Generic Open Architecture (GOA) Framework Standard” and provides an overview and rationale for SAE AS4893. The GOA Framework establishes an architectural framework to assist in the application of open systems interface standards to the design of specific hardware/software systems. The GOA Framework standard is intended for use by both system designers and system implementers in the development of open systems architectures. It is intended that domain specific guidelines be developed to provide clarification for application of the GOA Framework. The Generic Open Architecture (GOA) Framework was initially developed by the SAE to provide a framework which could be used to classify interfaces needed in airborne avionics systems. At the time of the development of the GOA Framework, development of such a classification was considered crucial to the application of open systems standards to military avionics. However, it was recognized
The mass of air required to burn a unit mass of fuel with no excess of oxygen or fuel left over is known as the stoichiometric air-fuel ratio. This ratio varies appreciably over the wide range of fuels - gasolines, diesel fuels, and alternative fuels - that might be considered for use in automotive engines. Although performance of engines operating on different fuels may be compared at the same air-fuel ratio or same fuel-air ratio, it is more appropriate to compare operation at the same equivalence ratio, for which a knowledge of stoichiometric air-fuel ratio is a prerequisite. This SAE Recommended Practice summarizes the computation of stoichiometric air-fuel ratios from a knowledge of a composition of air and the elemental composition of the fuel without a need for any information on the molecular weight of the fuel.
This document is intended to highlight critical design issues that a panel designer should understand when designing panels for NVIS applications. It is not intended to be a discussion of the benefits of one lighting technology versus another. Refer to ARP4168 for a more complete discussion of these lighting technologies.
This SAE Information Report provides information applicable to production Original Equipment Manufacturer antilock braking systems found on some past and current passenger cars and light trucks. It is intended for readers with a technical background. It does not include information about aftermarket devices or future antilock brake systems. Information in this document reflects that which was available to the committee at the time of publication.
This standard covers oronasal type masks which use a continuous flow oxygen supply. Each such mask comprises a facepiece with valves as required, a mask suspension device, a reservoir, or rebreather bag (when used), a length of tubing for connection to the oxygen supply source, and a means for allowing the crew to determine if oxygen is being delivered to the mask. The assembly shall be capable of being stowed suitably to meet the requirements of its intended use.
This SAE Aerospace Standard (AS) establishes the requirements for fluid fittings that combine both weld fitting end and 24° cone flareless fitting end connections for use in all types of fluid systems.
The following schematic diagrams reflect various methods of illustrating automotive transmission arrangements. These have been developed to facilitate a clear understanding of the functional interrelations of the gearing, clutches, hydrodynamic drive unit, and other transmission components. Two variations of transmission diagrams are used: in neutral (clutches not applied) and in gear. For illustrative purposes, some typical transmissions are shown.
This document covers flexible and semiflexible, reinforced and unreinforced air hoses fabricated from laminated and impregnated fabric, intended for use in aircraft heating, air conditioning, ventilating, defrosting, and/or deicing systems.
The purpose of this SAE Standard is to establish the specific minimum equipment performance requirements for recovery and recycling of HFC-134a that has been directly removed from, and is intended for reuse in, mobile air-conditioning (A/C) systems. It also is intended to establish requirements for equipment used to recharge HFC-134a to an accuracy level that meets Section 9 of this document and SAE J2099. The requirements apply to the following types of service equipment and their specific applications: a. Recovery/recycling equipment b. Recovery/recycling - refrigerant charging c. Refrigerant recharging equipment only
This document establishes methods to obtain, store, and access data about the health of a fiber optic network using commercial sensors located in or near the transceiver. This document is intended for: Managers, Engineers, Contracting Officers, Third Party Maintenance Agencies, and Quality Assurance.
This SAE Aerospace Standard (AS) covers batch qualification procedure for virgin and compounded polytetrafluoroethylene (PTFE) resins used for compression molding. AS9100 requires virgin and modified PTFE as a testing material be representative of production PTFE and/or parts. The testing specified herein is limited to tensile strength, elongation and specific gravity. Any other tests required by the purchaser must be specified separately.
This SAE Aerospace Standard (AS) establishes guidelines for the use of IEEE-1394-2008 Beta (formerly IEEE-1394b) as a data bus network in military and aerospace vehicles. It encompasses the data bus cable and its interface electronics for a system utilizing S400 over copper medium over extended lengths. This document contains extensions/restrictions to “off-the-shelf” IEEE-1394 standards, and assumes that the reader already has a working knowledge of IEEE-1394. This document does not identify specific environmental requirements (electromagnetic compatibility, temperature, vibration, etc.); such requirements will be vehicle-specific and even LRU-specific. However, the hardware requirements and examples contained herein do address many of the environmental conditions that military and aerospace vehicles may experience. One should refer to the appropriate sections of MIL-STD-461E for their particular LRU, and utilize handbooks such as MIL-HDBK-454A and MIL-HDBK-5400 for guidance. This
This SAE Aerospace Recommended Practice (ARP) provides the qualification test procedure requirements for low wattage halogen lamps (less than 35 watts) intended for use primarily in aircraft applications. The purpose of these tests is to provide a laboratory means of determining the performance characteristics of lamps under airplane power and other environmental conditions and to verify the integrity of the lamp design and production processes.
This SAE Standard covers unshielded cable, 22 gauge and larger, intended for use at a nominal system voltage up to 600 V or 1000 V (ACrms or DC). It is intended for use in surface vehicle electrical systems.
This document outlines the functional and design requirements for baggage/cargo tow tractors used for airline services.
This specification establishes the requirements for the following types of self-locking nuts in thread diameter sizes 0.1380 through 0.6250 inch: a Wrenching Nuts: i.e., hexagon, double hexagon, and spline nuts. b Anchor Nuts: i.e., plate nuts, gang channel nuts, and shank nuts. The wrenching nuts, shank nuts, and nut elements of plate and gang channel nuts are made of a corrosion- and heat-resistant nickel-base alloy of the type identified under the Unified Numbering System as UNS N07001 and of 180000 psi axial tensile strength at room temperature, with maximum conditioning of parts at 1400 °F prior to room temperature testing.
This specification covers a titanium alloy in the form of cold drawn wire.
This Aerospace Standard (AS) defines the requirements for polytetrafluoroethylene (PTFE) heavy duty hose assemblies suitable for use in aircraft and missile hydraulic fluid systems service to 8000 psi and -65 to 400 °F. Gaseous service shall be limited to 150 °F.
Items per page:
50
1 – 50 of 221567