Results
This specification covers a low-alloy steel in the form of investment castings.
This SAE Recommended Practice is prepared as a guideline to improve and maintain the quality of remanufactured automotive products. Installation of remanufactured or rebuilt products is often an economical way to repair a vehicle even though they may not fully be equivalent to original equipment parts. Before processing any part, a remanufacturer should determine if the original design and present condition of the core are suitable for remanufacturing, so as to provide durable operation of the part as well as acceptable performance when installed in a vehicle. The remanufacturer should also carefully consider the safety aspects of the product and any recommendations of the original manufacturer related to remanufacturing or rebuilding their product.
This SAE Aerospace Standard (AS) establishes minimum requirements for eddy current inspection of circular holes in nonferrous, metallic, low conductivity (less than 5% IACS) aircraft engine hardware with fasteners removed. The inspection is intended to be performed at maintenance and overhaul facilities on engine run hardware.
This SAE Aerospace Standard (AS) establishes the requirements for pipe threaded fluid connection fittings (see Section 6) for use in all types of fluid systems.
This specification establishes the requirements for self-locking nuts, wrenching type (i.e., hexagon, double hexagon, and spline drive), made of a corrosion and heat resistant steel of the type identified under the Unified Numbering System as UNS S66286.
This specification covers a 100% homopolymer of polychlorotrifluoroethylene, (PCTFE) in the form of thin wall tubing.
This specification covers an irradiated, thermally-stabilized, modified polyolefin plastic in the form of thin-wall, heat-shrinkable tubing with a low recovery temperature.
The previous revision of AIR5784 summarizes some of the available literature on cabin air study, engine oil composition, decomposition, and toxicity testing. This revision of AIR5784 includes literature and information on stakeholder involvement, selected air sampling studies, oil composition, and oil degradation, published from 2000 to 2023. The entire contents of the reviewed literature are not necessarily endorsed by either SAE or the members of the study group who produced it. This is not a comprehensive review but is intended to enable E-34 and other technical organizations to participate in informed discussions on the topic. Also, the review is intended to indicate where additional work may be necessary to properly gauge the potential role that turbine lubricants (and OPs) play in cabin air quality. The toxicology of oil fumes and their individual constituents is beyond the scope of this document and outside the remit of this committee.
This procurement specification covers tubular, blind rivets fabricated from a corrosion resistant nickel-copper alloy of the type identified under the Unified Numbering System as UNS N04405, and of 52 ksi minimum shear strength for self-plugging style rivets.
This specification covers requirements for material used in electrical insulating heat shrinkable components. The continuous operating temperature of these materials shall range from -75°C to +200°C (-103°F to +392°F). (See 6.1).
This specification covers a nitrile (NBR) rubber in the form of sheet, strip, tubing, extrusions, and molded shapes.
This Aerospace Standard (AS) covers the general minimum performance standards for generators/starter-generators and associated voltage regulators for use in direct current (DC) electric systems for civil aircraft.
This specification covers a butadiene-acrylonitrile (NBR) rubber in the form of molded rings, compression seals, o-ring cord, and molded-in-place gaskets for aeronautical and aerospace applications.
This specification covers an aluminum alloy powder metallurgy product in the form of sheet 0.010 to 0.250 inch (0.25 to 6.35 mm) in nominal thickness.
This specification covers a low-carbon steel in the form of bars and wire 0.750 inch (19.05 mm) and under in nominal diameter or distance between parallel sides.
This specification covers a low-alloy steel in the form of welding wire.
This specification covers an aluminum alloy powder metallurgy product in the form of round extrusions up to 3.5 inches (89 mm) in diameter and rectangular and other solid extrusions up to 10 square inches (64.5 cm2) in cross-sectional area. The maximum extrusion length is 100 inches (2.5 m).
This specification covers aluminum alloy brazing sheet for use in brazed aluminum joints.
This specification covers a chloroprene (CR) rubber in the form of sheet, strip, tubing, extrusions, and molded shapes.
This specification covers an ethylene propylene (EPDM) rubber in the form of sheet, strip, tubing, extrusions, and molded shapes other than O-rings.
This specification covers a silicone resin in the form of a two-component liquid.
This specification covers three types of rubber having good resistance to high and low temperature and hydrazine type propellants, but poor resistance to hydrocarbon oils or solvents. Hydrazines are hazardous chemicals. See “Dangerous Properties of Industrial Materials” by N. Irving Sax.
This specification covers a polytetrafluoroethylene resin in the form of extruded and sintered flexible tube reinforced with wire braid.
This specification covers the specific requirements for 7178 aluminum alloy plate and sheet material; the general requirements are covered in AMS-QQ-A-250.
This SAE Recommended Practice describes a laboratory test procedure for measuring the thickness of various resilient insulating padding materials that are used in the automotive industry. Such padding materials may include synthetic or non-synthetic materials, fibrous or cellular materials, high loft or compressed materials, single layer homogeneous or multilayer products, low and high surface density products. Some of these samples may be deformable and elastic, high loft thermal and acoustical fibrous materials, as well. The test method described herein has been developed to establish a means of a uniform procedure for measuring the thickness of different types of samples not only for application to all ground vehicles, but also may be applicable to other situations or conditions. The test method is designed to measure the thickness of flat samples and not formed parts. This test method does not purport to address all of the safety concerns, if any, associated with its use. It is the
This specification covers the engineering requirements for a treatment to provide enhanced corrosion resistance to sheet metal parts, such as brackets, spacers, and washers, fabricated from martensitic Corrosion-resistant steels, usually AMS 5504 or AMS 5508 and having hardness not higher than 40 HRC, or ferritic corrosion-resistant steels, usually AMS 5506. The treatment is not recommended for use on parts subject to impact in service.
This specification covers the requirements of composite blankets suitable for acoustical and thermal insulation of the walls of aircraft compartments within the temperature range of -65°F to +175°F (-54°C to +80°C).
This specification covers a silicone rubber in the form of a two-component liquid compound.
This specification covers types and classes of polysulfide sealing compound supplied as a two-component system suitable for application by brush, or by extrusion gun, spatula brush, or roller.
Items per page:
50
1 – 50 of 219718