Results
This SAE Standard establishes the test procedure, environment, and instrumentation for determining the sound levels of snowmobiles in the stationary test mode. This test method is intended to provide an accurate measurement of exhaust and other engine noise and may be used to evaluate new and in-use snowmobiles to determine compliance with noise control regulations. Sound level measurements obtained with this test method are not intended as an engineering determination of overall machine noise. For this purpose, the use of SAE J192 is recommended.
This SAE Aerospace Information Report (AIR) provides a description of a screening method for use in the field for verifying an AMS 1428 anti-icing fluid is above its minimum low shear viscosity as published with holdover time guidelines. The test will determine if the fluid is (a) satisfactory, (b) unsatisfactory, or (c) borderline needing more advanced viscometry testing. Other field tests may be required to determine if an anti-icing fluid is useable, such as refractive index, appearance or other tests as may be recommended by the fluid manufacturer.
Limited to the commercial aerospace industry where a request is made for a PO to have Direct Delivery Authorization (DDA), which includes an Appropriate Arrangement (AA) between the PO and the Design Organization (DO). In this process the DO is responsible for ensuring the continuous updating of design and airworthiness data to the PO, whilst the PO is responsible for assurance that the manufactured article conforms to approved design and airworthiness data. The PO is responsible to provide airworthiness release documentation.
This standard establishes the dimensional and visual quality requirements, lot requirements, and packaging and labeling requirements for O-rings machined from AMS3668 material. It shall be used for procurement purposes.
This SAE Aerospace Recommended Practice (ARP) provides to the aerospace industry a procedure for the consistent and accurate calculation of fuel flow using turbine flowmeters during development, production, and post overhaul/repair gas turbine engine testing.
This specification covers a low-alloy steel in the form of welding wire. Type 2 - copper coated wire was removed from this document (see 8.4).
This specification covers metric bolts and screws made from a corrosion and heat resistant, nickel-base alloy of the type identified under the Unified Numbering System as UNS N07001. The following specification designations and their properties are covered: MA3378 1210 MPa minimum ultimate tensile strength at room temperature 520 MPa stress-rupture strength at 730 °C MA3378-1 1210 MPa minimum ultimate tensile strength at room temperature 726 MPa minimum ultimate shear strength at room temperature
This SAE Aerospace Recommended Practice (ARP) contains methods used to measure the optical performance of airborne electronic flat panel display (FPD) systems. The methods described are specific to the direct view, liquid crystal matrix (x-y addressable) display technology used on aircraft flight decks. The focus of this document is on active matrix, liquid crystal displays (LCD). The majority of the procedures can be applied to other display technologies, however, it is cautioned that some techniques need to be tailored to different display technologies. The document covers monochrome and color LCD operation in the transmissive mode within the visual spectrum (the wavelength range of 380 to 780 nm). These procedures are adaptable to reflective and transflective displays paying special attention to the source illumination geometry. Photometric and colorimetric measurement procedures for airborne direct view CRT (cathode ray tube) displays are found in ARP1782. Optical measurement
This SAE Recommended Practice is part of the SAE J2534-2/X_0500 set of documents that extends the SAE J2534-1_0500 API (version 05.00) specification, and defines how to implement UART Echo Byte within the SAE J2534 API framework. This document details only the changes from SAE J2534-1_0500 and items not specifically detailed in this document are assumed to have not changed. An SAE J2534-2/3_0500 interface shall be compliant to the UART Echo Byte feature only when all the required functionality in this SAE Recommended Practice is implemented. Any functionality not required for compliance will be specifically marked as “optional” in this document. This document must be used in conjunction with the SAE J2534-2/BA_0500 and SAE J2534-2/RE_0500 documents.
This procedure covers vehicle operation and electric dynamometer (dyno) load coefficient adjustment to simulate track road load within dynamometer inertia and road load simulation capabilities.
This specification covers a mixture of liquid hydrocarbons and soluble additives.
This specification covers chrome-molybdenum (4130) steel bars and forging stock of aircraft quality.
This specification covers a premium aircraft-quality, low-alloy steel in the form of bars, forgings, mechanical tubing, and forging stock.
This Purchasing Specification, AMS6885/4, specifies the batch release and delivery requirements for film adhesive used for repair. This specification is applicable only when the film adhesive is used as part of the repair system defined in AMS6885 and AMS6885/1. This specification also defines the procedure and requirements for storage life extension of materials purchased against this specification. It is only applicable for materials qualified against AMS6885 (refer to PRI-QPL-AMS6885), and shall be carried out within the responsibility of the purchaser and under control of its Quality organisation.
This AIR was prepared to inform the aerospace industry about the electromagnetic interference measurement capability of spectrum analyzers. The spectrum analyzers considered are of the wide dispersion type which are electronically tuned over an octave or wider frequency range. The reason for limiting the AIR to this type of spectrum analyzer is that several manufacturers produce them as general-purpose instruments, and their use for EMI measurement will give significant time and cost savings. The objective of the AIR is to give a description of the spectrum analyzers, consider the analyzer parameters, and describe how the analyzers are usable for collection of EMI data. The operator of a spectrum analyzer should be thoroughly familiar with the analyzer and the technical concepts reviewed in this AIR before performing EMI measurements.
This Technical Specification gives information about technical requirements and qualification procedures of adhesive paste with or without thickening agent for core restoration of aircraft components.
These Protocols can be used for all forms of motorsports; however, only certain combinations of Green Racing Elements will result in motorsport competitions that are recognized as Green Racing events. As new information, fuels and technologies emerge, addendums or new protocols will be developed. The SAE International (SAE) Motorsports Engineering Activity is also an invaluable source of reference materials and ongoing technical advice providing access to the constantly evolving set of best safety and operational practices for current and emerging technologies. This is especially true with regard to high voltage safety and the adoption of other advanced propulsion and fuel system technologies.
This SAE Surface Vehicle Recommended Practice deals with electrostatic charge phenomena that may occur in automotive fuel systems and applies to the following: Fuels that are in a liquid state at ambient temperatures and atmospheric pressures and are contained in vehicle fuel tanks that operate at or near atmospheric pressure. This includes gasoline and diesel fuels, as well as their blends with additives such as alcohols, esters, and ethers, whether the additives are petroleum based or bio-fuel based. The group of components that comprise the fuel system (in contact and not in contact with fuels). Other components in proximity to the fuel system that may be affected by electrostatic fields caused by the fuel system. Electrostatic phenomena that arise from, or are affected by, the following aspects of vehicle or fuel system operation: Flowing fuel in the fuel delivery system. Flowing fuel being dispensed to the vehicle while it is being fueled.
This specification covers an aluminum alloy in the form of welding wire.
The following schematic diagrams reflect various methods of illustrating automotive transmission arrangements. These have been developed to facilitate a clear understanding of the functional interrelations of the gearing, clutches, hydrodynamic drive unit, and other transmission components. Two variations of transmission diagrams are used: in neutral (clutches not applied) and in gear. For illustrative purposes, some typical transmissions are shown.
This specification covers a carbon steel in the form of sheet, strip, and plate.
Items per page:
50
1 – 50 of 220040