Results
This document defines the test procedures and performance limits of steady state and transient voltage characteristics for 12 V, 24 V, or 48 V electrical power generating systems used in commercial ground vehicles.
This specification covers a low-alloy steel in the form of bars, forgings, mechanical tubing, and forging or tubing stock.
This SAE Standard covers the minimum requirements for metric sizes of nonmetallic tubing as manufactured for use in air brake systems. Nonreinforced products are designated type A and reinforced products type B. It is not intended to cover tubing for any portion of the system that operates below -40 °C (-40 °F), above +93 °C (+200 °F), above a maximum working gage pressure of 1.0 MPa (150 psi), or in an area subject to attack by battery acid. This tubing is intended for use in the brake system for connections that maintain a basically fixed relationship between components during vehicle operation. Coiled tube assemblies required for those installations where flexing occurs are covered by this standard and SAE J1131 to the extent of setting minimum requirements on the essentially straight tube and tube fitting connections, which are used in the construction of such assemblies.2 NOTE—As all elements of SAE J1394 are being merged into SAE J844, two separate documents are no longer
This SAE Recommended Practice summarizes the composition of modern automotive gasolines, the significance of their physical and chemical characteristics, and the pertinent test methods for defining or evaluating these properties.
This SAE Recommended Practice defines the principal terms and equations pertaining to automotive automatic transmission clutch plate, band, or other wet-friction systems. The terms apply directly to friction-system testing as is typically conducted on inertia-stop test equipment. Some terms can be directly applied to the analysis of friction in the transmission or brake assembly and other friction-test equipment. The glossary presents terms used to describe the set-up, testing, and results of tests as shown in Figure 1, which were taken on a clutch SAE No. 2 machine. The glossary is intended to provide a collection of definitions in the hope of eliminating confusion in development and their application to passenger cars and trucks. This document focuses on the terminology of friction-system testing. References for this type of testing are shown in Section 2.
This document establishes safety limits and performance requirements for gaseous hydrogen fuel dispensers used to fuel Hydrogen Powered Industrial Trucks (HPITs). It also describes several example fueling methods for gaseous hydrogen dispensers serving HPIT vehicles. SAE J2601-3 offers performance based fueling methods and provides guidance to fueling system builders as well as suppliers of hydrogen powered industrial trucks and operators of the hydrogen powered vehicle fleet(s). This fueling protocol for HPITs can support a wide range of hydrogen fuel cell hybrid electric vehicles including fork lifts, tractors, pallet jacks, on and off road utility, and specialty vehicles of all types. The mechanical connector geometry for H25 and H35 connectors are defined in SAE J2600 Compressed Hydrogen Surface Vehicle Refueling Connection Devices. Multiple fueling methods are described in this document and include: 1 Fill to Service Pressure with fixed area flow-limiting device 2 Fill to Target
This SAE Recommended Practice establishes uniform engineering nomenclature for wheels, hubs, rims, and their components used in truck, bus, and trailer applications. This nomenclature and accompanying drawings are intended to define functional truck wheel, hub, and rim designs. For nomenclature specific to “passenger-type” disc wheels, refer to SAE J1982. The International Standard (ISO) nomenclature is shown in parentheses when different than SAE J393.
This SAE Recommended Practice provides a Glossary of Terms commonly used to describe Seat Belt Restraint Systems Hardware and their function. These terms are currently defined in various SAE Recommended Practices but are sometimes inconsistent. It is intended for this document to supersede the definitions found in separate SAE Recommended Practices.
This material type has resistance to hot air, but generally has poor resistance to fuels and lubricants, but usage is not limited to such applications. Each application should be considered separately. This material type has a typical service temperature range of -85 to 500 °F (-65 to 260 °C). The operating temperature range of the material is a general temperature range, but the presence of particular fluids and design parameters may modify this range. Recommendations on the material selection are based on available technical data and are offered as suggestions only. Each user should make his own tests to determine the suitability for his own particular use.
This glossary provides accepted definitions for terms commonly used by manufacturers and users of electric wire and cable, and their components, intended for use on aerospace vehicles.
Develop terminology and definitions specifically for the automotive industry that defines greener and more sustainable materials and practices. The document will provide information and context for how and where the terms are used in the auto sector. In some cases, there may be more than one definition provided as some terms have different meanings in different countries.
This document is not a standard, it is a candidate for a standard being submitted to SAE for their consideration as a comment to SAE J2735. The term SAE J2735 SE candidate is used within this document to refer to this submission. This document specifies dialogs, messages, and the data frames and data elements that make up the messages specifically for use by applications intended to utilize the 5.9 GHz Dedicated Short Range Communications for Wireless Access in Vehicular Environments (DSRC/WAVE, referenced in this document simply as “DSRC"), communications systems. Although the scope of this Standard is focused on DSRC, these dialogs, messages, data frames and data elements have been designed, to the extent possible, to be of use for applications that may be deployed in conjunction with other wireless communications technologies. This standard therefore specifies the definitive message structure and provides sufficient background information to allow readers to properly interpret the
This SAE Aerospace Recommended Practice (ARP) provides minimum standards and environmental design requirement recommendations for lighting and control in galley areas. It also addresses electrical shock hazard in galley areas. The use of “shall” in this document expresses provisions that are binding. Non-mandatory provisions use the term “should.”
This SAE Standard sets forth accepted definitions and terminology of major components and parts peculiar to snowmobiles.
This glossary of tire military/industry represents the latest state-of-the-art terms and definitions for military use. This SAE Recommended Practice shall remain open for comments from the reader and shall also be reviewed and updated periodically. Many similar terms and definitions were reviewed from which the ones best applied to military use were selected. It is the purpose of this task force to provide technical definitions in present day use.
This recommended best practice outlines a method for estimating CO2-equivalent emissions using life cycle analysis.
This SAE Recommended Practice is applicable to oil-to-air and oil-to-coolant oil coolers installed on mobile or stationary equipment and provides a glossary of oil cooler nomenclature. Such oil coolers may be used for the purpose of cooling automatic transmission fluid, hydraulic system oil, retarder system fluid, engine oil, etc. This document outlines the methods of procuring the test data to determine the operating characteristics of the oil cooling system and the interpretation of the results.
This document defines various vehicular noises and vibrations that are attributed to being created by the foundation brake components of the vehicle, particularly on passenger cars and light trucks. These definitions cover both disc and drum brakes. The frequency ranges from near zero Hz (tactile sensations) all the way up to 17 kHz, or the upper limit of normal hearing. These noises and vibrations may either directly radiate off the brake system or provide the excitation energy that causes other vehicle components to react.
This glossary is intended to provide engineers, metallurgists, and production personnel with uniform definitions of commonly used carbon sheet and strip terms. The glossary serves to supplement information and photographs reported in SAE J810, J763, J877, J863, and J403. Many of the terms listed apply only to hot-dipped zinc-coated products or to uncoated products. The letter C following the term identifies a term applying to coated materials, while the letters NC identify a term applying to uncoated materials. Where no identification is provided, the term is common to both.
This document lists recommended noun titles for drawings of support equipment and provides definitions for each. The use of secondary modifiers to distinguish a part from similar parts is also covered.
The terms included in the Glossary are general in nature and may not apply to all manufacturers’ systems. All terms in Section 3 apply to automotive inflatable restraint systems in general which are initiated by an electric or mechanical stimulus upon receipt of a signal from a sensor. These terms are intended to reflect existing designs and the Glossary will be updated as information on other types of systems becomes available. Appendix A is included to identify terminology that is no longer in common use or specifically applicable to inflatable restraint systems, but was published in the December 2001 version of SAE J1538.
Items per page:
50
1 – 50 of 221567